Résumé du contenu de la page N° 1
IMPORTANT MANUAL Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
PP265E27
In struc tions. Fail ure to do so
can result in serious injury.
SNOW THROWER
428550 08.12.09 CL
Always Wear Eye Protection During Operation
Printed in the U.S.A.
Résumé du contenu de la page N° 2
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA
Résumé du contenu de la page N° 3
6. When cleaning, repairing or inspecting the snow thrower, Clearing a Clogged Discharge Chute stop the engine and make certain the collector/impel- Hand contact with the rotating impeller inside the discharge ler and all moving parts have stopped. Disconnect the chute is the most common cause of injury associated with spark plug wire and keep the wire away from the plug to snow throwers. Never use your hand to clean out the dis- prevent someone from accidentally starting the engine. charge
Résumé du contenu de la page N° 4
PARTS PACKED SEPARATELY IN CARTON (1) POWER CORD (1) MULTI- (3) RETAINER (198563) WRENCH SPRINGS (180684) (169675) (2) LOCKNUTS (2) SHEAR BOLTS 1/4-20 x 1-3/4 1/4-20 (192090) (73800400) (2) FLAT WASHERS SAFTEY IGNITION KEY (S) (429955) (2) CARRIAGE BOLTS (1) LOCKNUT (1) CARRIAGE BOLT 3/8-16 x 2.25 5/16-18 5/16-18 x 5/8 (751153) (72250505) (1) LOCKNUT (1) SHOULDER (1) LOCKNUT 3/8 (1) WASHER 3/8 1/4-20 BOLT 1/4-20 (1) SPRING (2) HANDLE KNOBS (191730) (179829) (184505) (19131316) (73800600) AS
Résumé du contenu de la page N° 5
ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the INSTALL TRACTION DRIVE CONTROL ROD chute rotator head to snow thrower and making ad just ments (See Figs. 3 and 4) to the skid plates. The traction drive control rod is installed on the snow UNFOLD UPPER HANDLE thrower. 1. Raise upper handle to the operating position and 1. Remove plastic tie securing rod to lower handle. tight en handle knobs securely. Additional carriage 2. With top end of rod positioned unde
Résumé du contenu de la page N° 6
ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATOR INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) HEAD (See Fig. 7) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. NOTE: The multi-wrench provided in your parts bag may Slide straight rod end through the small hole in the be used to install the chute rotator head. vinyl sleeve. Hook spring in hole in rod end. 1. Place discharge chute assembly on top of chute base
Résumé du contenu de la page N° 7
ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Cable eyelet will be loose on shoulder bolt. 3. Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown. SPRIN
Résumé du contenu de la page N° 8
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Résumé du contenu de la page N° 9
OPERATION POWER CORD AUGER GAS O LINE DISCHARGE CHUTE CONTROL LEVER PLUG CONTROL FILLER LEVER DEFLECTOR REMOTE CAP DRIVE SPEED CONTROL LEVER CON TROL LEVER ELECTRIC PRIM ER START BUTTON TRACTION CHUTE DRIVE DE FLEC TOR CONTROL LEVER CHOKE CON- TROL SAFETY IGNITION KEY DISCHARGE LIGHT FUEL SHUT-OFF VALVE CHUTE THROTTLE RECOIL (AUXILIARY) STARTER HANDLE CLEAN-OUT TOOL HANDLE KNOB MUF FLER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL TOOLBOX LOCATION ON THE ENGINE. ACTUAL LOCA
Résumé du contenu de la page N° 10
OPERATION The operation of any snow thrower can result TO USE THROTTLE CONTROL (See Fig. 13) in foreign objects thrown into the eyes, which The throttle control is located on the engine. Always op er ate can result in severe eye damage. Always wear the snow thrower with the engine at full throttle. Full throttle safety glasses or eye shields while operating offers the best snow thrower performance. your snow thrower or performing any ad just- ments or repairs. We recommend standard safe
Résumé du contenu de la page N° 11
OPERATION TO THROW SNOW (See Fig. 15) TO MOVE FORWARD AND BACKWARD (See Fig. 17) The auger rotation is controlled by the auger control lever SELF-PROPELLING, forward and reverse movement of located on the right side handle. the snow thrower, is controlled by the traction drive control lever located on the left side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. • Squeeze traction drive control lever to handle to en gage the drive system. • Release the au
Résumé du contenu de la page N° 12
OPERATION TO ADJUST SKID PLATES (See Fig. 18) ADD GASOLINE (See Fig. 19) NOTE: The wrench provided in your parts bag may be • Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with used to adjust the skid plates. a minimum of 87 octane. Do not mix oil with gasoline. Skid plates are located on each side of the auger housing Purchase fuel in quan ti ties that can be used within 30 and adjust the clearance between the scraper bar an
Résumé du contenu de la page N° 13
OPERATION COLD START - ELECTRIC STARTER IF RECOIL STARTER HAS FROZEN 1. Insert safety ignition key (tied to recoil start cord) into If the recoil starter has frozen and will not turn the engine, ignition slot until it clicks. DO NOT turn the key. Keep proceed as follows: the extra safety ignition key in a safe place. 1. Grasp the recoil starter handle and slowly pull as much 2. Place throttle control in “FAST” position. rope out of the starter as possible. 3. Rotate choke control to “FULL”
Résumé du contenu de la page N° 14
MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To ➀ SAE 5W-30 Motor Oil receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some ad just - See “ENGINE” in ➁ ments will need to be made periodically to properly maintain Maintenance section your snow thrower. General ➂ At least once a season, check to see if you sho
Résumé du contenu de la page N° 15
MAINTENANCE BELTS TO CHANGE ENGINE OIL Check belts for deterioration and wear after every 50 hours Determine temperature range anticipated before next oil of operation and replace if necessary. The belts are not change. All oil must meet API service classification SG–SL. ad just able. Replace belts if they begin to slip from wear. • Be sure snow thrower is on level surface. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual). • Oil will drain more freely when
Résumé du contenu de la page N° 16
SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to WARNING: To avoid serious injury, before STOP position. Wait for all moving parts to stop. performing any service or ad just ments: 2. Remove safety ignition key and disconnect spark plug 1. Be sure throttle is in STOP position. wire from spark plug. Place wire where it cannot come in contact with spark plug. 2. Remove safety ignition key. 3. Align holes in impeller hub with holes in impeller shaft 3. Make sure t
Résumé du contenu de la page N° 17
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 22) 8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around The auger and traction drive belts are not adjustable. If the pulleys. belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced HINT: Insert a 3/8" drive ratchet (in the “ON” position) into by a service center/department. the square hole in idler arm and rotate ratchet clockwise to re
Résumé du contenu de la page N° 18
SERVICE AND ADJUSTMENTS TO REMOVE WHEELS (See Fig. 23) ENGINE • Remove the klik pin and remove wheel from axle. SEE ENGINE MANUAL. IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To dis en gage CARBURETOR drive system from the wheels (for pushing or trans port ing Your carburetor is not adjustable. Engine performance the snow thrower), remove klik pin from wheel hub and should not be affected at altitudes up to 2,134 meters. If insert p
Résumé du contenu de la page N° 19
STORAGE Immediately prepare your snow thrower for storage at • Empty the fuel tank by starting the engine and letting the end of the season or if the unit will not be used for 30 it run until the fuel lines and car bu re tor are empty. days or more. • Never use engine or carburetor cleaner prod ucts in the fuel tank or permanent damage may occur. WARNING: Never store the snow • Use fresh fuel next season. thrower with gaso line in the tank in side a build ing where fumes may reach an NOTE:
Résumé du contenu de la page N° 20
TROUBLESHOOTING See appropriate section in manual unless directed to an authorized service center/department. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position 5. Choke in OFF position. 5. Move to F
