Résumé du contenu de la page N° 1
FRANÇAIS
ENGLISH ESPAÑOL
R
Pleasedo notreturn productto retailer.
Porfavor, no devuelvael producto al lugardecompra.
Veuilleznepasretournerleproduitau détaillant.
1--800--554--6723
Registeryourproductonlineat:
Registresu producto en líneaen:
Enregistrezvotreproduiten ligneàl’adresse:
www.poulanpro.com
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
PP1000E
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result
Résumé du contenu de la page N° 2
IDENTIFICATIONOFSAFETYSYMBOLS DANGER: Blademoves momentarily after the trigger switchis released. S Theblade canseriously cut your or others. S Allow blade to stop beforeremovingit from the cut. S Donot overreach. WARNING: This unit canbe dangerous! Careless or improper use cancauseserious injury. Read the operator’s manual before use. Failure to follow instructions could result in serious injury. Save operator’s manual. Hazard zonefor thrownobjects. S Blade canthrow objects violently. S You and
Résumé du contenu de la page N° 3
S Alwayswearheavy,longpants,longsleeves, useofapolarizedwalloutlet. Thisplugwill boots, and gloves. fit into the polarized wall outlet only one S Alwayswearfootprotection. Donotgobare- way. If plug does not fit fully into the wall foot or wear sandals. outlet,reversetheplug. Ifitstilldoesnotfit, S Secure hair above shoulder length. Secure contact a qualified electrician to install the or remove looseclothingor clothingwith properwalloutlet. Donotchangetheequip- loosely hanging ties, straps, tass
Résumé du contenu de la page N° 4
S Ground Fault Circuit Interrupter (GFCI) S Hold the unit firmly with both hands. protectionshouldbeprovidedonthecircuit S Keep firm footing andbalance. Do notover- oroutlettobeusedforthepowerhead. Re- reach or stand on unstable surfaces. ceptacles are available having built-in S Always keep the wheel in contact with the GFCI protection and may be used for this ground. measure of safety. S Keep all parts of your body away from the blade and muffler. UNIT/MAINTENANCESAFETY S Always pushtheunitslo
Résumé du contenu de la page N° 5
OPERATION KNOWYOUREDGERATTACHMENT READTHISINSTRUCTIONMANUALANDSAFETYRULESBEFOREOPERATINGYOUREDG- ER ATTACHMENT. Compare the illustrations with your attachment to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. Hanger Depth Adjustment Knob Shaft BladeShield Wheel Gearbox Edger Blade BLADE DEPTHADJUSTMENTKNOB The BLADE is designedtocut sod. The DEPTH ADJUSTMENT KNOB is used toadjust thewheel for bladecutting depth. 2. Pressandh
Résumé du contenu de la page N° 6
EDGING WARNING: Make sure the locking/ Asyoubecomefamiliarwithuseofyouredger release button is locked in the primary hole attachment,youwillbeabletodetermineyour andtheknobissecurelytightenedbeforeop- own operating pace. Conditions such as erating the unit. Using the wrong hole could depthof cut and material beingcut willregu- lead to serious injury or damage to the unit. latethespeedandtimerequiredforyouredg- ing job. S Allowtheenginetowarmupbeforeyoubegin edging. S Increasetheenginespeedbefore
Résumé du contenu de la page N° 7
MAINTENANCE BLADEMAINTENANCE WARNING: Alwaysstopunitanddis- connect spark plug wire(or disconnectpow- WARNING: The blade will continue erheadfrompowersource)beforeperforming to spin after the engine stops or after the maintenance. throttle trigger has been released. To avoid serious injury, make sure the blade has CHECKFORDAMAGEDOR stopped coasting and disconnect the spark WORNPARTS plug (or disconnect powerhead from power Contact an authorized service dealer for re- source)beforeperformingworko
Résumé du contenu de la page N° 8
STORAGE S Clean the entireattachment. WARNING: Perform the following S Inspect the blade shield area and clean any steps after eachuse: dirt, grass, leaves, or debris that has col- lected. Inspectthebladeandbladeshield;re- S Allow attachment and gearbox to cool be- forestoringor transporting. place a blade that is bent, warped, cracked, broken or damaged in any other way. S Storeattachmentwithbladeshieldinplace. Position attachment so that any sharp ob- S Lightly oil external metalsurfaces. ject
