Résumé du contenu de la page N° 1
889 WEIGHT STACK OPTION
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
USER’S GUIDE
CLASS H 1 Version: 889108
PART # 7305301 Revision: 06/19/02
REV . A
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Safety Statement.............2 Assembly Instructions......4-13 General Notes..................3 General Maintenance........14 Tools Required................3 Warranty Statement..........15 Parts List.........................4 Product Services..............16 Insert-Registration Card IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES! 1. Before using, read all the warnings and instructions 6.
Résumé du contenu de la page N° 3
IMPORTANT NOTES Please note: * Thank you for purchasing the ParaBody 889 Weight Stack Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated. Tools Required for Asse
Résumé du contenu de la page N° 4
PARTS LIST DESCRIPTION KEY PART # QTY KEY DESCRIPTION QTY PART # UPRIGHT 1 LEA6814309 1 22 LEA3203301 VINYL CAP 2 ADJ FOOT SUPPORT 2 LEA6800610 1 23 LEA6542402 3/16 X 1-3/4 X 5-1/4” PLTE 2 3 STACK BASE 1 24 3/4 X 1-1/2” GLIDE 1 LEA6814009 LEA6416601 TOP BOOM 4 LEA6813709 1 25 LEA7292501 WEIGHT PLATE 20 LAT BAR SUPPORT 5 1 26 WEIGHT STACK CUSHION 2 LEA6801110 LEA3108002 76” GUIDE ROD 6 LEA6816501 2 27 LEA6595201 GUIDE ROD BUSHING 2 LOW ROW BAR 7 LEA6274410 1 28 LEA7308601 WEIGHT STACK LBLS (1-26
Résumé du contenu de la page N° 5
3 21 16 24 FIGURE 2 STEP 2: • Insert two 2” END CAP (16) into the ends of the STACK BASE (3) as shown in FIGURE 2. • Attach four 3/4 X 1-1/2” GLIDES (24) to the inside of the tube on the STACK BASE (3) as shown in FIGURE 2 using the following steps: • Thoroughly clean all surfaces where the 3/4 X 1-1/2” GLIDES (24) are to be attached. • Remove the 3/4 X 1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces. • SECURELY assemble one SPRING PIN AS
Résumé du contenu de la page N° 6
3/8 X 4” 38 30 1 UPRIGHT FRAME LOWER CROSS SUPPORT 3 21 2 30 3/8” 29 LOW HEIGHT FIGURE 4 LOCK NUT STEP 4: • NOTE: It may be necessary to loosen the 1/2 X 3-1/4” BOLTS of the LOWER CROSS SUPPORT connecting to the UPRIGHT FRAME before beginning STEP 4. • SECURELY assemble the STACK BASE (3) and the UPRIGHT (1) to the LOWER CROSS SUPPORT using two 3/8 X 4” BOLTS (38), four 3/8” WASHERS (30), and two 3/8” LOW HEIGHT LOCK NUTS (29). See FIGURE 4. • Pull back on the SPRING PIN (21)
Résumé du contenu de la page N° 7
STEP 5: • Insert two GUIDE RODS (6) into the STACK BASE (3) as shown in FIGURE 5. Lubricate the GUIDE RODS (6) with a silicon or teflon spray that is available at most hardware stores. 15 • Slide two WEIGHT STACK CUSHIONS (26) down over the GUIDE RODS (6). See FIGURE 5. • Using EXTREME CARE slide twenty WEIGHT PLATES (25) down over the GUIDE 6 RODS (6) with the key-hole facing as shown in FIGURE 5. • Carefully Slide the HEAD PLATE ASSEMBLY (36) down over the GUIDE RODS (6) onto the weigh
Résumé du contenu de la page N° 8
FIGURE 6 16 13 4 31 30 UPRIGHT 27 31 13 15 1 32 3/8 X 2-3/4” UPPER CROSS SUPPORT 6 30 38 3/8 X 4” STEP 6: • NOTE: It may be necessary to loosen the 1/2 X 3-1/4” BOLTS of the UPPER CROSS SUPPORT connecting the UPRIGHT FRAME before beginning STEP 6. • Insert two GUIDE ROD BUSHINGS (27) into the TOP BOOM (4) as shown in FIGURE 6. • Insert two 3 X 2” END CAPS (13) into the ends of the TOP BOOM (4). See FIGURE 6. • Insert two 2” SQ. END CAPS (16) into the ends of the TOP BOOM
Résumé du contenu de la page N° 9
FIGURE 7 4 3/8” LOW HEIGHT 29 5 22 32 3/8 X 2-3/4 STEP 7: • SECURELY assemble the LAT BAR SUPPORT (5) to the TOP BOOM (4) using one 3/8 X 2-3/4” (32) and one 3/8” LOW HEIGHT LOCK NUT (29). See FIGURE 7. • Slide two VINYL CAPS (22) over the LAT BAR SUPPORT (5) as shown in FIGURE 7. 31 FIGURE 8 33 4 Make sure CABLE 3/8 X 2-3/4” 32 9 is routed over bolt! 12 STEP 8: • Route the 115-3/4” CABLE (12) through the TOP BOOM (4) as shown in FIGURE 8. (NOTE: It may be necessary to remove
Résumé du contenu de la page N° 10
FIGURE 9 4 30 31 23 9 35 3/8 X 2” 12 !IMPORTANT! SECUREL Y TIGHTEN JAM NUT 36 17 STEP 9: • Slide ring of WEIGHT STACK SELECTOR PIN (17) over top of HEAD PLATE ASSEMBLY (36) • Screw the threaded end of the CABLE (12) approximately 3/4” into the end of the HEAD PLATE ASSEMBLY (36) and tighten jam nut securely. See FIGURE 9. • Place one 3-1/2” PULLEY (9) into the loop of the CABLE (12) below the second and third PULLEY of the TOP BOOM (4) as shown in FIGURE 9. • LOOSELY assemble two
Résumé du contenu de la page N° 11
1 33 31 33 10 11 30 32 3/8 X 2-3/4” FIGURE 10 STEP 10: • Route the threaded end of the 124” CABLE (11) through the slot of the UPRIGHT (1) then SECURELY assemble one 4-1/2” PULLEY (10) to the UPRIGHT (1) using two 3/8 X 2-3/4” BOLTS (32), two 3/8” FLANGE SPACERS (33), two 3/8” WASHERS (30), and two 3/8” LOCK NUTS (31). (NOTE: The CABLE (11) should be routed between the pulley and the retaining bolt as shown in FIG- URE 10.) 11
Résumé du contenu de la page N° 12
31 9 23 30 35 3/8 X 2” 11 SECUREL Y TIGHTEN JAM NUT! 3 FIGURE 11 STEP 11: • Loop the 124” CABLE (11) around one 3-1/2” PULLEY (9) as shown in FIGURE 11. • LOOSELY assemble the 3-1/2” PULLEY (9) to the 3/16 X 1-3/4 X 5-1/4” PLATES (23) using one 3/8 X 2” BOLT (35), two 3/8” WASHERS (30), and one 3/8” LOCK NUT (31). See FIGURE 11. • SECURELY thread the end of the 124” CABLE (11) 3/4 of the way into into the threaded housing on the STACK BASE (3) and SECURELY tighten jam nut. • SEC
Résumé du contenu de la page N° 13
14 11 34 36 8 34 12 34 37 7 14 FIGURE 12 STEP 12: • Slide two 1 X 8” GRIPS (14) on the LOW ROW BAR (7) and two 1 X 8” GRIPS (14) on the LAT BAR (8) as shown in FIGURE 12. • Attach the LAT BAR (8) to the ball end of the upper CABLE (12) using one 5/16” SNAP HOOK (34) as shown in FIGURE 12. • Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (11) using one 12-LINK CHAIN (37) and two 5/16” SNAP HOOKS (34) as shown in FIGURE 12. • If the HEAD PLATE (36) does not sit on top o
Résumé du contenu de la page N° 14
MAINTENANCE Please note: * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your ParaBody customer service representative at (800) 328-9714. * Inspect equipment daily. Tighten all loose connections are replace worn parts immediately. Failure to do so may result in serious injury * Lubricate guide rods with a teflon based (or equivalent) lubricant on a regular basis * PLEASE RECORD THE INFORMATION REQUES
Résumé du contenu de la page N° 15
LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product. 2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will
Résumé du contenu de la page N° 16
LIFE FITNESS 14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A. Tel: 763.323.4500 Fax: 763.323.4797 800.328.9714 (Toll-free within the U.S. and Canada) www.parabody.com INTERNATIONAL OFFICES Life FitnessAtlantic BV Life Fitness (UK) Ltd. Atlantic Headquarters Queen Adelaide Bijdorpplein 25-31 Ely, Cambs CB7 4UB 2992 LB Barendrecht United Kingdom The Netherlands Phone CSS: (01353) 665507 Phone: (180) 646 666 Fax CSS: (01353) 666719 Fax: (180) 646 703 Life Fitness EUROPE GmbH Lif
