Résumé du contenu de la page N° 1
Chain Vise Recipro Saw
MODEL JR3010
INSTRUCTION MANUAL
SPECIFICATIONS
Net weight
Length of stroke Strokes per minute Vise capacity Overall length ,without
28 mm 11-118") 0 - 2,200 :,?,--':-:;; 435 mm 117-1/8") 2.9 kg (6.4 Ibs)
Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
Résumé du contenu de la page N° 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to and adjusting wrenches are removed from tool before turning see that keys it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are
Résumé du contenu de la page N° 4
ADDITIONAL SAFETY RULES 1. Wear a hard hat (safety helmet), safety glasses and/or face shield. It is also highly recommended that you wear a dust mask, ear protectors and thickly padded gloves. 2. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately. 3. Do not attempt to cut workpieces larger than specified in this manual (especially hollow pipe). The blade might snap and cause an injury. 4. Hold the tool firmly. 5. Be sure no o
Résumé du contenu de la page N° 5
Installing or removing saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. The blade installing position varies depending upon the type of blade being used. Install the blade in the proper position as shown in the figures below. Installing position for blades No. 25 and 26. Installing position for blades No. 21, 22, 23 and 24. To install the blade, loosen the bolt with the hex wrench. Insert the blade between the blade
Résumé du contenu de la page N° 6
Installing or removing vise assembly To install the vise assembly, insert the shaft of the vise assembly into the hole in the housing as far as it will go. The shaft of the vise assembly will be grasped by the stop- per automatically. Make sure that the vise assembly cannot be removed even though you try to pull it out. To remove the vise assembly, raise the stopper and then pull the vise assembly out while turning the vise assembly. CAUTION : Do not use the vise assembly when cutting
Résumé du contenu de la page N° 7
Operation 1. Cutting with the vise assembly : Secure the tool to the workpiece as de- scribed in “Securing tool to workpiece” section. Bring the blade into light con- tact with the workpiece. First, make a pilot groove, using a slower speed until the blade has cut to a depth of 1 - 3 mm (3/64” - 1/8’)). Then use a faster speed to continue cutting. CAUTION : Do not lift the tool handle too hard during operation. This may cause a bevel cut, damage to the blade or damage to the tool. W
Résumé du contenu de la page N° 8
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in th
Résumé du contenu de la page N° 9
Oty. Teeth Overall Tooth Saw Blades Application Part ## Per Pkg. Per Inch Length Specification High Carbon Steel 1723018-0A 1 1s I Wood Cutting Blade Cuts nail free wood 723018-A-5 1 6' 6' Fleam Ground -rough In work. 7230 1 8-A-2 6" 1.049" I High Carbon Steel Cuts nail free wood Fleam Ground 723018-6-5 - rough in work. 723018-6-1 12" 1.049") Cuts composition 6" High Alloy Steel 723018-OC 10 materials - resists 7230 18-CS 6 6' Milled 1.031") nail damage. 1 I I I 1723018-O
Résumé du contenu de la page N° 10
Overall I Tooth Part I my. I Teeth Saw Blades Per Pkg. Per Inch Length Specification I Application 6" Cuts nail embedded Bi-metal Blade 723017-E5 6" 1 Mi~~i~ei~o,,, 1 wood -roughing in Combination of high 723017-E-2 6' work. speed steel teeth welded to a shatter proof flexiblf Cuts nail embedded backed blade. Ultra long 723017-F-5 I 5 I 6 12" I Mi{$Tei:o,,) I wood - roughing in life blade. work. 723017.0A 10 10 Cuts nail embedded 723017-A5 10 E" 1 Mi&Tei:l,,, 1 wood - nonferrous
Résumé du contenu de la page N° 11
Aug.-17-'89 US CHAIN VISE RECIPRO SAW Model JR3010 Note: The switch, noise suppressor and other part configurations may differ from country to country. 11
Résumé du contenu de la page N° 12
MODEL JR3010 Aug -17'89 US 'i:M ,& DESCRIPTION 'i:M A&, DESCRIPTION MACHINE MACHINE ~ ~ 1 1 41 1 Thin Washer 6 2 1 42 1 Nsadla Bearing 510 1 43 1 P," 5 3 4 1 44 3 Her Socket Head Bolf M5x16 lWilh Washer1 5 1 45 3 Spring Washer 4 6 2 46 3 Pan Head Screw M4x10 7 2 47 1 Rsiammg Ring 5-10 8 1 48 I Gear Housmg 9 2 49 I Gam Holder IO 2 50 1 Thrust Nssdla Bearing 3041 11 2 51 1 GBW 12 2 4 52 Pan Head Screw M5x30 13 2 53 4 Spring Washer 5 14 1 54 1 Pin 6 15 1 55 1 Fan 75 16 1 56
