Résumé du contenu de la page N° 1
WT-5360U
433 MHz
Radio Controlled Alarm Clock
With Projection Time
Instruction Manual
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Topic Page Inventory of Contents/ Additional Equipment 3 Glossary of Common Terms 3 QUICK SET-UP GUIDE 4 DETAILED SET-UP GUIDE Battery Installation 5 PROGRAM MODE Programming Sequence 6 Function Buttons 6 Time Zone Setting 6-7 Manual Time Setting 7 Year and Date Setting 7 12/24-Hour Clock Setting 8 Indoor Temperature Setting 8 Daylight Saving Time (DST) Setting 8 FEATURES & OPERATIONS Features 8 Radio Controlled Time 8-9 Time P
Résumé du contenu de la page N° 3
INVENTORY OF CONTENTS 1. WT-5360 Alarm Clock 2. AC adapter/transformer 3. Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) Two fresh 1.5V AA alkaline batteries (optional when using AC adapter) FEATURES OF PROJECTION ALARM CLOCK Operation of these features is in section III. 1. Time Zone Setting 2. Manual Time Display 3. Year Setting 4. Calendar Display 5. Time Display in 12/24 Hour Mode 6. Indoor Temperature Display 7. Daylight Saving Time (DST) On/Off
Résumé du contenu de la page N° 4
I. QUICK SET-UP GUIDE Hint: Use good quality alkaline batteries and avoid rechargeable batteries. 1. We recommend beginning the set-up procedure at night when the WWVB signal is easiest to receive. 2. It is also highly recommended to set the projection alarm in a window or other area free of interference in the area of your home that is closest to Colorado (the source of the WWVB signal). NOTE: The above steps are not required but can help the projection alarm receive the signal fa
Résumé du contenu de la page N° 5
battery cover II. DETAILED SET-UP GUIDE A. BATTERY INSTALLATION 1. Remove the battery cover on the backside of the projection alarm. 2. Observe the correct polarity, and install 2 AA batteries. 3. In addition to or instead of installing batteries, the AC adapter can be used. Simply plug the adapter into the receptacle on the underneath AC adapter side of the alarm clock, and then plug in the adapter. receptacle 4. Replace the battery cover. 5. The projector will activate and rema
Résumé du contenu de la page N° 6
III. PROGRAM MODE To enter the Program Mode, hold down the “MODE/MIN” button for 3 seconds, until the time zone flashes at the bottom of the display. The Program Mode Guide is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to program the projection alarm. Complete programming is usually done for the initial set-up, and will require you to skip step 1 and 2 of programming sections D-H. To exit the setting mode simply w
Résumé du contenu de la page N° 7
-4h Atlantic Time 4. -5h Eastern Time (default setting) -6h Central Time -7h Mountain Time -8h Pacific Time -9h Alaskan Time -10h Hawaiian Time -11h, -12h Next two time zones West of HAW 0h Greenwich Mean Time -1h, -2h, -3h Three time zones West of GMT NOTE: The U.S. time zones will show abbreviations as opposed to the numerical time zone indicator. For example Eastern Time will display “ET” when the Eastern Time Zone is selected 5. Press and release the “
Résumé du contenu de la page N° 8
F. 12/24-HOUR CLOCK SETTING 1. Hold down the “MODE/MIN” button for 3 seconds; the time zone will appear flashing at the bottom of the LCD. 2. Press and release the “SNOOZE” bar 5 times to advance to the 12/24-hour clock setting. 3. Press and release the “MODE/MIN” button to select either a 12-hour clock or a 24- hour clock. 4. Press and release the “SNOOZE” bar to confirm selection and advance to the Indoor Temperature Display. G. INDOOR TEMPERATURE DISPLAY 1. Hold down the “MODE/MIN”
Résumé du contenu de la page N° 9
3. When the time signal has been received successfully, the tower icon will remain steady until midnight. 4. The projection alarm will search for a signal every night when reception is best. 5. It is possible that your projection alarm may not be exactly on the second due to the variance in the quartz. However, the clock will adjust the quartz timing over the course of several days to be very accurate--under 0.10 seconds per day. C. TIME PROJECTION 1. When plugged into an AC outlet, t
Résumé du contenu de la page N° 10
c. To disable the alarm for 24 hours, press and release any button other than the “SNOOZE” bar or display direction buttons. NOTE: The alarm will sound in a 3-step crescendo for 80 seconds if the “SNOOZE” bar is not pressed. 4. VIEWING TIME ALARM a. To momentarily view the time the alarm is set for, press and hold down the “SNOOZE” bar for 2 seconds, and the alarm time will appear for 2 seconds. The clock will automatically return to normal operations after the 2 seconds. b. To s
Résumé du contenu de la page N° 11
2) Wait overnight for signal. 3) Be sure the projection alarm is at least 6 feet from any electrical devices, i.e. TV sets, computers, or other radio controlled clocks. 4) Remove batteries for five minutes, reinsert and leave the unit alone overnight without pressing buttons. 5) If problems persist contact La Crosse Technology. Problem: Hour is incorrect (minute is correct). Solution: Be sure correct time zone and daylight saving time are selected. Note: For any questions not answered,
Résumé du contenu de la page N° 12
authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or d
Résumé du contenu de la page N° 13
FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. La Crosse Technology Made in China WT-5360 FCC ID: OMO-01RX (Receiver), THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DE
