Instruction d'utilisation Life Fitness Seated Leg Curl

Résumé du contenu de la page N° 1

Seated Leg Curl
Assembly Instructions

Résumé du contenu de la page N° 2

Seated Leg Curl Assembly Instructions Item Qty Description Part Number Item Qty Description Part Number 1 1 Front Brace 80176XX 28 1 Long Spacer 7511503 2 1 Rear Brace 80175XX 29 2 Bearing 3243201 3 1 Tower 79854XX 30 1 Work Arm 80215XX 4 4 M10 x 130mm Bolt 3251720 31 1 Bearing Housing Cap 7922701 5 67 3/8” Flat Washer 3102514 32 1 Counter Weight 8008801 6 22 M10 Nylock Nut 3242002 33 1 Medium Spacer 7330006 7 1 Seat Frame 80211XX 34 2 Bearing 3235601 8 6 M10 x 90mm Bolt 3251715 35 1 Short Space

Résumé du contenu de la page N° 3

Résumé du contenu de la page N° 4

Seated Leg Curl Assembly Instructions 1. LOOSELY assemble the FRONT BRACE (1) and REAR BRACE (2) to the TOWER (3) using four M10 X 130mm BOLTS (4), eight 3/8" SAE WASH- ERS (5) and four M10 NYLOCK NUTS (6) as shown. 2. LOOSELY assemble the SEAT FRAME (7) to the FRONT BRACE (1) and REAR BRACE (2) using four M10 X 90mm BOLTS (8), eight 3/8" SAE WASHERS (5) and four M10 NYLOCK NUTS (6) as shown. 3. LOOSELY assemble the TOP BRACE (9) to the SEAT FRAME (7) and TOWER (3) using two M10 X 35mm BOLTS (10

Résumé du contenu de la page N° 5

6. Assemble the OUTPUT CAM (15), OUTPUT PLATE (16), and OUTPUT RING (17) using three M10 X 45mm BOLTS (18) and three 3/8" SAE WASHERS (5) as shown. Tighten the BOLTS securely. 7. Assemble the REAR SHROUD (19) and FRONT SHROUD (20) to the TOWER (3) using four M10 X 20mm BOLTS (21), four 3/8" SAE WASH- ERS (5) as shown. Be sure all tabs along the sides and top of the SHROUDS are fully engaged in the slots located inside the TOWER. Tighten the BOLTS securely. Do not over-tighten the BOLTS. 8. Secur

Résumé du contenu de la page N° 6

Seated Leg Curl Assembly Instructions 10. Attach the KNEE SUPPORT (26) to the MAIN PIVOT BRACKET (12) and SEAT FRAME (7) using seven M10 X 30mm BOLTS (27), fourteen 3/8" SAE WASHERS (5) and seven M10 NYLOCK NUTS (6) as shown. Tighten the BOLT and NUTS securely. Insert the KNEE SUPPORT ENDCAP (49). 11. Insert the LONG SPACER (28) and two BEARINGS (29) into the MAIN PIVOT BRACKET (12) as shown. Carefully insert the WORKARM (30) into the MAIN PIVOT BRACKET and secure it with one M10 X 25mm BOLT (22

Résumé du contenu de la page N° 7

13. Insert the MEDIUM SPACER (33), two BEARINGS (34) and one SHORT SPACER (35) into the KNEE SUPPORT (26) as shown. Carefully insert the KNEE HANDLES (36) into the KNEE SUPPORT and secure it with one M10 X 25mm HEX BOLT (37) and one FENDER WASHER (48). Tighten the BOLT securely. Insert the BEARING HOUSING CAP (38) as shown. 14. Attach the KNEE PAD (39) to the KNEE HANDLES (36) using two M10 X 25mm BOLTS (22) and two 3/8" SAE WASHERS (5). Tighten the BOLTS securely. 15. Attach the PAD SUPPORT PL

Résumé du contenu de la page N° 8

Seated Leg Curl Assembly Instructions NOTE: Some components have been removed from the illustration for clarity. 17. Insert one end of the CABLE (44) into the cam of the WORKARM (29). Thread the cable approximately 1/2 inch into the cam. Route the CABLE beneath the CAM GUARD (24) and around the OUTPUT CAM ASSEMBLY (A). Insert the remaining end of the CABLE through the inner hole of the OUTPUT CAM ASSEMBLY. Insert the CABLE RETAINING PLATE (45) over the end of the CABLE. Install two HEX JAM NUTS