Résumé du contenu de la page N° 1
INSTALLATION AND OPERATION INSTRUCTIONS
TM
Vent-Free Millivolt
Dual-Listed Gas Log Sets
Gas Train Models: Log Set Models:
LSVFSD-NG LSVFSD-18 Logs
LSVFSD-LP LSVFSD-24 Logs
Log Sets Sold Separately
P/N 850,051M Rev. A, 08/2007
Installer: Leave This Manual With The Appliance.
Consumer: Retain This Manual For Future Reference.
In the Commonwealth of Massachusetts:
• Installation must be performed by a licensed plumber or gas fitter
US
• See Table of Contents for location of additional
Shado
Résumé du contenu de la page N° 2
IMPORTANT SAFETY AND WARNING WARNINGS INFORMATION • Allow the appliance to cool before servicing. Always shut off any electricity or gas to the appliance while READ THIS MANUAL IN ITS ENTIRETY AND UNDER- performing service work. STAND THESE RULES TO FOLLOW FOR SAFETY. • The appliance and its individual shut-off valve must be disconnected from the gas supply piping system while WARNINGS performing any tests of the gas supply piping system at If the information in this manual is
Résumé du contenu de la page N° 3
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW PACKAGING LIST GAS APPLIANCE MANUFACTURED BY LENNOX HEARTH PRODUCTS. the gas train models lsVFsD-Ng and lsVFsD-lP are packaged with the following: When you purchased your new gas-log heaters, you joined the ranks 1 - one base/grate assembly of thousands of individuals whose answer to their home heating needs - one bag of lava rock reflects their concern for efficiency and our environment. We extend our - one damper clamp continued support
Résumé du contenu de la page N° 4
SEE TABLE 3 ON PAGE 16 FOR BTU INPUT AND GAS PRESSURE CODES REQUIREMENTS adhere to all local codes or in their absence the latest edition of the Do not install these Dual-Listed Gas Log Appliances in a bedroom or National Fuel gas code aNsi Z.1 or NFP a 54-latest edition which can a bathroom as all units exceed maximum allowable BTU/hr input of be obtained from the american National standards institute, inc. (140 10,000. Broadway, New York, NY, 10018) or National Fire Protection associ
Résumé du contenu de la page N° 5
Requirements for the Commonwealth of Massachusetts COMBUSTION AND VENTILATION AIR Note: The following requirements reference various Massachusetts and national codes not contained in this document. t his heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion un-vented r oom Heaters shall be installed in accordance with 5 7 cmr and ventilation air. t he heater may be located in unusually tight construc- 0.00
Résumé du contenu de la page N° 6
4. compare the maximum Btu/Hr the space can support with the actual Note: Illustrations shown in this manual reflect “typical” installations amount of Btu/Hr used. with nominal dimensions and are for reference only. Actual installations may vary due to individual design preferences. However, always main- _________ Btu/Hr tain minimum clearances to combustible materials and do not violate (max. the space can support) any specific installation requirements. Refer to Figures 2 through 8 for
Résumé du contenu de la page N° 7
Noncombustible Material Requirements with No Mantel Installed (A) Noncombustible Requirements for Safe Installation Material Measurement 1" or more adjustable canopy not required. 42" 8" minimum to 1" install adjustable canopy. Min. less than 8" extend noncombustible material to at least 8" and install adjustable canopy (Figure 4). 16" or Min. extend noncombustible material to a height of at least 1". Table 1 Noncombustible Material Heights and Mantel Location Figure 2 - Clearances (A) Non
Résumé du contenu de la page N° 8
Example: The bottom of the mantel may project from the wall a maxi- INSTALLATION mum of 2-1/2" at a minimum of 8" above the opening. The top shelf of the mantel may project a maximum of 6" at a minimum of 14-1/2" above the opening. WARNINGS • Do not use a blower insert, heat exchanger 12" insert or other accessory not approved 10" for use with this heater. 8" • Installed decorative glass door enclosures must be 26" 6" fully opened when operating this dual-listed gas 22-1/2" applia
Résumé du contenu de la page N° 9
the appliance gas inlet connection is /8" NPt at the regulator/valve, r eplace the test point plug after pressure measurement ensuring no located on the left side facing the appliance. if a right side connection is gas leaks. required, the connection pipe may be piped under the rear of the appliance to end at the left hand side for connection to the inlet. When tightening up the joint to the regulator hold the regulator securely Step 4. PLACING THE LOGS with a wrench to prevent the regulato
Résumé du contenu de la page N° 10
LOG PLACEMENT INSTRUCTIONS . Place middle log onto left middle grate locating pin and the rear ember bed locating pin as shown in Figure 13. 1. Place rear ember bed as shown in Figure 11. Middle Log Top Burner Install Ember bed from behind Locating top burner Pins Rear Ember Bed Locating Pins Position Ember Bed All the Way Forward in Gas Train Assembly Figure 11 - Install Rear Ember Bed Figure 13 - Install Middle Log . Place rear log onto the two rear grate locating pins as shown in Figur
Résumé du contenu de la page N° 11
5. Place left top log onto rear log and middle log locating pins as 8. Place left t op t wig (4" model only) onto corresponding notch shown in Figure 15. on rear log as shown in Figure 18A. the front of the left t op t wig should be up against and behind the left top log. Left Top Log Locating Pins Left Top Log Left Top Twig Figure 15 - Install Left Top Log 6. Place the center top log onto the rear log locating pin and middle log locating pin as shown in Figure 16. Front Ember Bed Center
Résumé du contenu de la page N° 12
in normal operation, at full rate, after 15 minutes the following flame appearance should be observed: WARNING Failure to position the parts in accordance with Figure Burner And Flame Characteristics 21 or failure to use only parts specifically approved the shadowdance™ gas log set features a new concept in integrated with this appliance may result in property damage or burner and log design. the flames from the burner travel horizontally personal injury. through the log set and em
Résumé du contenu de la page N° 13
REPLACEMENT PARTS OPERATION AND CARE OF YOUR APPLIANCE an expanded view of the appliance with numbered parts and a parts list can 1. Appliance operation may be controlled through the ON/OFF unit be found on Page 19. all parts should be ordered through your distributor rocker switch, located in the bottom front of the appliance or through or dealer. Parts will be shipped at prevailing prices at time of order. an optional remote control. When ordering repair parts, always give the following
Résumé du contenu de la page N° 14
Knob Extensions ACCESSORY COMPONENTS Knob extensions for both the on/off and High/low functions are available. Standard Remote Control System (Model RCL) t he model rcl (standard) r emote control system, features a simplistic on/off control function for the fireplace. this model includes a hand-held transmitter, a remote receiver with wall-mount cover plate and all hardware required to install the unit. the remote receiver can be wall or hearth mounted. the transmitter has oN and oFF f
Résumé du contenu de la page N° 15
Charred Ember Kit ACCESSORY COMPONENTS (CONTINUED) an optional -piece charred ember Kit is available to enhance the beauty of the log set. Gas Log Sets Left Charred Ember Right Charred Ember 18" Gas Log Set Charred Ember Kit Cat. No. Model No. Description H6894 LSVFSD-CEK Charred Ember Kit Bag of Volcanic Stone Volcanic stone is available for use with these appliances. 24" Gas Log Set Decorative Volcanic Stone Gas Log Sets* Cat. No. Model No. Description Cat. No. Model No. Description 80L42
Résumé du contenu de la page N° 16
CAUTION: Label all wires prior to disconnection when servicing controls. THERMOPILE Wiring errors can cause improper and dangerous operation. PILOT (O.D.S.) If any of the original wire as supplied must be replaced, it must be replaced with Type AWM 105°C – 18 GA. wire. ASSEMBLY MILLIVOLT VALVE WHITE RED WHITE WHITE IGNITION ON/OFF WIRE SWITCH OPTIONAL REMOTE CONTROL PILOT PIEZO (MILLIVOLT) IGNITER Figure 22 - Millivolt Wiring Diagram Vented/Unvented Gas Log Appliance Technical Chart For Milliv
Résumé du contenu de la page N° 17
O O L I P T O it TPTH TP TH L I P F F LIGHTING INSTRUCTIONS – MILLIVOLT FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. this appliance has a pilot which must be lighted with a piezo • Do not use any phone in your building. igniter. When lighting the pilot, follow these instructions • Immediately call your gas supplier from a neighbor’s exactly. phone. • I
Résumé du contenu de la page N° 18
VENTED/UNVENTED TROUBLESHOOTING GUIDE OBSERVED PROBLEM POSSIBLE CAUSE REMEDY 1. When igniter button is A. igniter electrode positioned wrong. replace igniter. pressed, there is no spark B. igniter electrode broken. replace igniter. at oDs/pilot. C. igniter electrode not connected to igniter cable. reconnect igniter cable. D. igniter cable pinched or wet. Free igniter cable if pinched by any metal or tubing. Keep igniter cable dry. E. Piezo igniter nut is loose. t ighten nut. F. Broken igniter
Résumé du contenu de la page N° 19
REPLACEMENT PARTS LIST (MILLIVOLT) - SHADOWDANCE™ SERIES Replacement Parts List (Millivolt) - Shadowdance™ Series, Models LSVFSD-NG and LSVFSD-LP (18" and 24") No. Description Catalog Number 1. Valve, millivolt (Natural) H10 Valve, millivolt (Propane, l.P.g.) H478 2. ember Bed Front H910 3. ember Bed rear H911 4. Bottom Burner H91 5. t op Burner H91 6. Piezo igniter 10K86 7. oDs Pilot assembly, millivolt (Natural) H411 8. oDs Pilot assembly, millivolt (Propane, l.P.g.) H4170 9. K
Résumé du contenu de la page N° 20
lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. consult your local distributor for fireplace code information. Printed in u.s.a. © 007 by lennox Hearth Products 1110 West t aft avenue P/N 850,051M REV. A 08/2007 orange, ca 9865 FPO
