Résumé du contenu de la page N° 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
POWERHOUSE ELITE
Hardware Identifier
SMITH MACHINE
Assembly Instruction
PHE 9000
Parts List
Warranty
Ordering Parts
Model
PHE 9000
Retain This
Manual for
Reference
03-17-04
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
Résumé du contenu de la page N° 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 SMITH MACHINE HARDWARE PACK….......…............................................. 3 SMITH MACHINE ASSEMBLY INSTRUCTIONS............................................. 5 EXPLODED DIAGRAM…………………………………………………………….. 18 SMITH MACHINE PARTS LIST………..…………………………………………..
Résumé du contenu de la page N° 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Résumé du contenu de la page N° 4
SMITH MACHINE HARDEWARE PACK 3
Résumé du contenu de la page N° 5
SMITH MACHINE HARDEWARE PACK 4
Résumé du contenu de la page N° 6
SMITH MACHINE HARDEWARE PACK 5
Résumé du contenu de la page N° 7
SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left & Right Base Frame (#1 & 2) by a Cross Brace (#3) in the mid-span. Secure each end of the Cross Brace to each Base Frame with two M10 x 2 ¾” Carriage Bolts (#77), one 4 ¾” x 2” Bracket (#32), two Ø ¾” Washers (#87), and
Résumé du contenu de la page N° 8
STEP 2 (See Diagram 2) A.) Attach a Front Vertical Frame (#6) to the Right Base Frame (#2). Secure it with two M10 x 2 ¾” Carriage Bolts (#77), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#88). Do not tighten the Nuts and Bolts yet. B.) Repeat Procedure A above to install the other side. C.) Connect the two Front Vertical Frames (#6) with an Upper Frame (#10) on the top. Secure each end with two M10 x 3 ½” Carriage Bolts (#75), Ø3/4” Washers (#87) and M10 Aircraft Nuts (#88). D.) In
Résumé du contenu de la page N° 9
DIAGRAM2 8
Résumé du contenu de la page N° 10
STEP 3 (See Diagram 3) A.) Attach the Rear Vertical Frame (#14) to the Rear Base Frame (#5). Secure it with two M10 x 2 ½” Allen Bolts (#69), four Ø ¾” Washers (#87), and two M10 Aircraft Nuts (#88). Slide the Sliding Weight Post (#13) onto the Rear Vertical Frame (#14). B.) Place the Lat Bar Frame Bracket (#15) onto the Rear & Middle Vertical Frame (#4 & #14). Secure it to the Rear Vertical Frame (#14) with two M10 x ¾” Allen Bolts (#73) and Ø ¾” Washers (#87). Secure it to the Middl
Résumé du contenu de la page N° 11
STEP 4 (See Diagram 4) A.) Attach the Left & Right Lat Bar Frames (#16 & #17) to the Upper Frame (#10). Align the holes and secure each Lat Bar Frame to Upper Frame with one M10 x 5” Allen Bolt (#67), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88). Do not tighten the Nut and Bolt yet. B.) Attach the Left & Right Lat Bar Frames to the Lat Bar Frame Bracket (#15) from each side. Secure them with two M10 x 5 3/8” Allen Bolts (#66), four Ø ¾” Washers (#87), and two M10 Aircraft Nuts
Résumé du contenu de la page N° 12
STEP 5 (See Diagram 5) A.) Attach the Butterfly Base (#23) to the front of Middle Vertical Frame (#4). Attach the Butterfly Pulley Bracket (#24) to the back of the Frame. Secure them with two M10 x 2 ¾” Carriage Bolts (#77), Ø ¾” Washers (#87), and M10 Aircraft Nuts (#88). B.) Slide the Left Butterfly (#26) onto the pivot on the Butterfly Base. Secure it with one Lock Ring (#64), M6 x 3/8” Allen Bolt (#84), and M6 Aircraft Nut (#90). C.) Attach the Butterfly Arm Pad (#34) to the Left Bu
Résumé du contenu de la page N° 13
CABLE LOOP DIAGRAM 12
Résumé du contenu de la page N° 14
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Insert the 242” Upper Cable (#35) through the swivel pulley bracket pre-installed in the top front of the Right Lat Bar Frame (#17). B.) Install a Ball Stopper (#86) onto the end of the Cable. Attach a U-shaped Connector (#91) to the end of the Cable. C.) Attach a Short Chain (#40) in between the opening on the Connector and secure it with a M10 x 1 3/8” Allen Bolt (#72), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88). D.
Résumé du contenu de la page N° 15
DIAGRAM 6 14
Résumé du contenu de la page N° 16
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of the 76” Butterfly Cable (#36) to the clip on the Left Butterfly (#26). Draw the Cable to the Butterfly Base Bracket (#24). B.) Attach a Pulley (#45) to the Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71), one L-shaped Bracket (#25), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88). C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley Bracket (#30). Secure it with
Résumé du contenu de la page N° 17
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach one end of the 140” High-Low Cable (#38) to the bracket on the Sliding Weight Post (#13). Secure it with one M10 x 1 3/8” Allen Bolt (#72), two Ø ¾” Washers (#87), and one M10 Aircraft Nut (#88). B.) Draw the Cable upward to the open bracket underneath the Lat Bar Frame Bracket (#15). Install another Pulley. C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Double Floating Pulley Bracket (#29). Install a Pul
Résumé du contenu de la page N° 18
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 68” Lower Cable (#37) to the opening on the bottom of Middle Vertical Frame (#4). Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#69), two Long Pulley Bushings (#48), and one M10 Aircraft Nut (#88). B.) Draw the Cable underneath the Pulley to the open bracket on the Rear Base Frame (#5). Install a Pulley to the bracket. C.) Draw the Cable around the Pulley then upward to the Double Floating Pulley Brack
Résumé du contenu de la page N° 19
18
Résumé du contenu de la page N° 20
SMITH MACHINE PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Left Base Frame 1 51 2” x 1 ¾” Sleeve 2 2 Right Base Frame 1 52 1” End Cap 2 3 Cross Brace 1 53 Ø 1” Con-shaped End Cap 8 4 Middle Vertical Frame 1 54 6” x 2” Rubber Bumper 1 5 Rear Base Frame 1 55 Ø 3” Rubber Bumper 4 6 Front Vertical Frame 2 56 Ø 1 ½” Rubber Bumper 1 7 Guide Rod 2 57 Ø 2 ½” Rubber Bumper 2 8 Foot Plate 1 58 2” End Cap 5 9 Safety Stop Frame 2 59 Single Handle 2 10 Upper Frame 1 60 1 5/8” x 2 3/8” E
