Instruction d'utilisation Impex PHC 750

Résumé du contenu de la page N° 1

NOTE:
Please read all instructions
carefully before using this
product






Safety Notice
POWERHOUSE CLUB
Hardware Identifier


Assembly Instruction PHC 750

Parts List

Warranty

Ordering Parts



Model
PHC 750


Retain This
Manual for
Reference


09-26-01


IMPEX FITNESS PRODUCTS
OWNER'S
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
MANUAL
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com

Résumé du contenu de la page N° 2

TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM……………………………………………………………... 8 PARTS LIST………………………………

Résumé du contenu de la page N° 3

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per

Résumé du contenu de la page N° 4

3

Résumé du contenu de la page N° 5

ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Align the holes and secure them with one Bracket (#20), two M10 x 3 1/8” Carriage Bolts (#38), two ∅ ¾” Washers (#45), and two M10 Aircraft Nuts (#44) on each end of

Résumé du contenu de la page N° 6

STEP 2 (See Diagram 2) A.) Attach the Leg Developer Holder (#5) to the Front Stabilizer (#6). Secure it with three M10 x 5/8” Allen Bolts (#43) and ∅ ¾” Washers (#45). B.) Attach the Leg Developer Holder (#5) to the front of Main Seat Support (#3). Secure it with one M10 x 2 ½” Carriage Bolt (#56), two M10 x 2 ¾” Carriage Bolts (#39), three ∅ ¾” Washers (#45), and three M10 Aircraft Nuts (#44). C.) Attach the back of Main Seat Support (#3) to the Cross Brace (#2). Secure it with one

Résumé du contenu de la page N° 7

STEP 3 (See Diagram 3) A.) Attach the hole-side of the Seat Bracket (#11) to the Pivot on the Main Seat Support (#3). Push two Bushings (#36) into the holes on the Pivot. B.) Attach the Backrest Supports (#10) to the Pivot. Secure it with one M10 x 7 ¼” Hex Bolt (#41), two ∅ ¾” Washers (#45), and one M10 Aircraft Nut (#44). DO NOT tighten the nut and bolt yet. Place the Backrest Incline Support (#9) in between the two Backrest Supports (#10). Securely tighten the Nut (#44) and Bolt (

Résumé du contenu de la page N° 8

STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#14) to the bracket on top of the Leg Developer Holder (#5). Secure it with an Axle (#48), two ∅ ¾” Washers (#45), and two M10 x 5/8” Allen Bolts (#43). Slide the Olympic Sleeve (#55) onto the post on the Leg Developer. Attach a Spring Clip (#21) to the Sleeve. Note: When using the decline position to do Ab exercises, place at least 30lbs of weights on the Sleeve to hold down the Leg Developer. B.) Insert one Foam Roll Tube (#15) ha

Résumé du contenu de la page N° 9

8

Résumé du contenu de la page N° 10

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Upright Beam 2 2 Cross Brace 1 3 Main Seat Support 1 4 Backrest Adjustment Bar 1 5 Leg Developer Holder 1 6 Front Stabilizer 1 7 Crutch 2 8 Weight Post 2 9 Backrest Incline Support 1 10 Backrest Support 2 11 Seat Bracket 1 12 Seat Incline Adjustment 1 13 Arm Curl Stand 1 14 Leg Developer 1 15 Foam Roll Tube 3 16 Foam Roll 6 17 Seat Pad 1 18 Backrest Board 1 19 Arm Curl Pad 1 20 Bracket 3 21 Spring Clip 3 22 Rubber Bumper 2 2

Résumé du contenu de la page N° 11

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cu