Instruction d'utilisation Impex PHC -265

Résumé du contenu de la page N° 1

NOTE:
Please read all instructions
carefully before using this
product



Table of Contents


Safety Notice
POWERHOUSE BENCH

Hardware Identifier

PHC -265
Assembly Instruction

Parts List

Warranty

Ordering Parts



Model
PHC 265


Retain This
Manual for
Reference


08-07-02

OWNER'S
IMPEX FITNESS PRODUCTS
MANUAL
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fi

Résumé du contenu de la page N° 2

TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE.....................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 4 EXPLODED DIAGRAM………....................................

Résumé du contenu de la page N° 3

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per

Résumé du contenu de la page N° 4

3

Résumé du contenu de la page N° 5

ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Rear Upright Beams (#1) by the Cross Brace (#2) in the mid-span. Align the holes then secure each end of Cross Brace with one Bracket (#13), two M10 x 2 3/8” Hex Bolts (#25), four ∅ ¾” Washers (#33), and two M10 Aircraft Nuts (#30). B.) Insert the Bac

Résumé du contenu de la page N° 6

A.) Attach the rear of the Main Seat Support (#3) to the Cross Brace (#2). Secure it with one Bracket (#13), two M10 x 2 3/8” Hex Bolts (#25), four ∅ ¾” Washers (#33), and two M10 Aircraft Nuts (#30). B.) Attach the front of the Main Seat Support (#3) to the Front Support (#4). Secure them with two M10 x 1” Hex Bolts (#26), four ∅ ¾” Washers (#33), and two M10 Aircraft Nuts (#30). C.) Attach one end of the Diagonal Support (#5) to the Main Seat Support (#3) and secure it with one M8 x 2

Résumé du contenu de la page N° 7

A.) Attach the front holes on the Backrest Supports (#7) to the pivot on the Main Seat Support (#3). Place the other end of the Backrest Supports (#7) on the Backrest Adjustment Bar (#6). Place the Backrest Board (#8) onto the Backrest Supports (#7). Secure it with four M6 x 1 3/8” Hex Bolts (#29) and ∅ ½” Washers (#35). B.) Place the Seat Pad (#9) onto the Main Seat Support (#3). Secure it with four M6 x 1 3/8” Hex Bolts (#29) and ∅ ½” Washers (#35). DIAGRAM 3 6 STEP 4 (See D

Résumé du contenu de la page N° 8

A.) Attach the Leg Developer (#10) to the front of Main Seat Support (#3). Secure it with a Hex Socket Axle (#23) and Hex Socket Screw (#24). Attach one Spring Clip (#14) onto the weight post on the Leg Developer. B.) Insert the two Foam Roll Tubes (#11) halfway through the holes on the Leg Developer. Push four Foam Rolls (#12) onto the Foam Roll Tubes from both ends. C.) Attach a ∅3/4” Washer (#33) onto a M10 x 4 ½” Hex Bolt (#43). Insert the Bolt through the Butterfly (#40) and secure

Résumé du contenu de la page N° 9

8

Résumé du contenu de la page N° 10

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Rear Upright Beam 2 2 Cross Brace 1 3 Main Seat Support 1 4 Front Support 1 5 Diagonal Support 1 6 Backrest Adjustment Bar 1 7 Backrest Support 2 8 Backrest Board 1 9 Seat Pad 1 10 Leg Developer 1 11 Foam Roll Tube 2 12 Foam Roll 4 13 Bracket 3 14 Spring Clip 3 15 ∅1” Sleeve 2 16 Left Safety Hook 1 17 Right Safety Hook 1 18 Bushing 6 19 1 ½” Square End Cap 12 20 1” Square End Cap 2 21

Résumé du contenu de la page N° 11

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cu