Instruction d'utilisation Impex MWB-855

Résumé du contenu de la page N° 1

NOTE:
Please read all instructions
carefully before using this
product



Table of Contents


Safety Notice
MARCY OLYMPIC BENCH
Hardware Pack


MWB-855
Assembly Instruction

Parts List

Warranty

Ordering Parts



Model
MWB 855


Retain This
Manual for
Reference


07-25-03

OWNER'S

MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness

Résumé du contenu de la page N° 2

TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICE....................................................................... 2 HARDWARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM........................................................

Résumé du contenu de la page N° 3

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso

Résumé du contenu de la page N° 4

HARDWARE PACK 3

Résumé du contenu de la page N° 5

ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Align the holes and secure each end of the Cross Brace with two M10 x 3 1/8” Carriage Bolts (#44), one 4 ¾” x 2” Bracket (#21), two ∅ ¾” Washers (#52), and two M10 Aircraft Nu

Résumé du contenu de la page N° 6

STEP 2 (See Diagram 2) A.) Attach the Leg Developer Holder (#5) to the Front Stabilizer (#4). Secure it with three M10 x 5/8” Allen Bolts (#47) and ∅ ¾” Washers (#52). B.) Attach the Main Seat Support (#3) to the Leg Developer Holder (#5). Secure it with three M10 x 2 ¾” Carriage Bolts (#45), M10 Aircraft Nuts (#51) and ∅ ¾” Washers (#52). C.) Attach the Main Seat Support (#3) to the Cross Brace (#2). Secure it with two M10 x 2 ¾” Carriage Bolts (#45), one 4 ¾” x 2” Bracket (#21)

Résumé du contenu de la page N° 7

STEP 3 (See Diagram 3) A.) Attach the Seat Bracket (#13) to the pivot on the Main Seat Support (#3). Push two Bushings (#22) through the holes on the Seat Bracket into both ends of the pivot. B.) Attach Backrest Incline Support (#7) in between the two Backrest Supports (#6) and insert both ends into the side-holes on the Backrest Supports. Attach the Backrest Supports to the Bushings. Secure it with one M10 x 7 ¼” Allen Bolt (#43), two ∅ ¾” Washers (#52), and one M10 Aircraft Nut (#51

Résumé du contenu de la page N° 8

STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#14) to the Leg Developer Holder (#5). Secure it with an Axle (#39), two M10 x 5/8” Allen Bolts (#47), and two Ø ¾” Washers (#52). B.) Insert one Foam Tube (#12) halfway through the hole on the Leg Developer Holder. Insert two Foam Tubes halfway through the holes on the Leg Developer. C.) Push six Foam Rolls (#37) onto the Tubes from both ends. Plug six Foam Roll End Caps (#32) into the ends. D.) Attach the Curl Bar Handle Suppo

Résumé du contenu de la page N° 9

8

Résumé du contenu de la page N° 10

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Upright Beam 2 2 Cross Brace 1 3 Main Seat Support 1 4 Front Stabilizer 1 5 Leg Developer Holder 1 6 Backrest Support 2 7 Backrest Incline Support 1 8 Backrest Adjustment Bar 1 9 Arm Curl Stand 1 10 Crutch 2 11 Weight Post 2 12 Foam Tube 3 13 Seat Bracket 1 14 Leg Developer 1 15 Curl Bar Handle Support 1 16 Curl Bar Handle 1 17 Backrest Board 1 18 Seat 1 19 Arm Curl Pad 1 20 Seat Incline Adjustment 1 21 4 ¾” x 2” Bracke

Résumé du contenu de la page N° 11

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cust