Résumé du contenu de la page N° 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
COMPETITOR
Safety Notice
CB-349 BENCH
Hardware Identifier
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
CB-349
Retain This
Manual for
Reference
July 15, 2004
IMPEX INC.
OWNER'S
14777 Don Julian Rd., City of Industry, CA 91746
MANUAL Tel: (800) 999-8899 Fax (626) 961-9966
www.impex-fitness.com
info
Résumé du contenu de la page N° 2
TABLE OF CONTENTS BEFORE YOU BEGIN...............................................................................................1 IMPORTANT SAFETY NOTICE................................................................................2 HARDWARE IDENTIFIER.........................................................................................3 ASSEMBLY INSTRUCTIONS....................................................................................4 EXPLODED DIAGRAM...............
Résumé du contenu de la page N° 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Résumé du contenu de la page N° 4
3
Résumé du contenu de la page N° 5
ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches and Allen Wrenches STEP 1 (SEE Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#15) in the Mid-span. Secure them with two M10 x 2 3/8” Hex Bolts (#2), four ∅ ¾” Washers (#3), one Bracket (#7), and two M10 Aircraft Nuts (#4) on each end of the Cross Brace. B.) Insert the Backrest Adjustment Bar (#10) through a selected hole to obtain desired incline of Backrest. C.
Résumé du contenu de la page N° 6
STEP 2 (SEE DIAGRAM 2) A.) Connect the Front Stabilizer (#42) to the Main Seat Support (#52) and secure them with two M10 x ¾” Hex Bolts (#46), four ∅ ¾” Washers (#3), and two M10 Aircraft Nuts (#4). DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support (#52) to the open bracket on the Cross Brace (#15). Secure the rear hole on the bracket with one M10 x 2 3/8” Bolt (#2), two ∅ ¾” Washers (#3), and one M10 Aircraft Nut (#4). Secure the other hole with a 3” Lock Pin (#
Résumé du contenu de la page N° 7
STEP 3 (SEE DIAGRAM 3) A.）Attach the Leg Developer (#38) onto the bracket on the Front Stabilizer (#42). Secure it with a Hex Socket Axle (#44) and Hex Socket Screw (#45). B.) Insert two Foam Roll Tubes (#39) halfway through the hole on the Leg Developer (#38). Push four Foam Rolls (#37) onto the tubes from both sides. C.）Place a Spring Clip (#34) onto the post on the Leg Developer . DIAGRAM 3 6
Résumé du contenu de la page N° 8
STEP 4 (SEE DIAGRAM 4) A.) Attach the hole-side of the Backrest Supports (#16) onto both ends of the Pivot on the Main Seat Support (#52) and place the other side rest against the Backrest Adjustment Bar (#10). B.) Place the Backrest Board (#18) onto the Backrest Supports (#16). Secure it with four M6 x 1 3/8” Hex Bolts (#50) and ∅ ½” Washers (#51). C.) Place Seat (#19) onto the bracket on the Main Seat Support (#52). Align the holes and secure the Seat with four M6 x 1 3/8” Hex Bol
Résumé du contenu de la page N° 9
STEP 5 (SEE Diagram 5) A.) Attach the ball end of the Cable to the Pulley (#28). Place the Pulley in the open slot on the Lat Bar Frame (#31). Secure it with one M10 x 2 1/8” Hex Bolt (#32), two Bushings (#29), two ∅ ¾” Washers (#3), and one M10 Aircraft Nut (#4). B.) Slide the Weight Holder (#33) onto the Lat Bar Frame from the bottom. Connect the Cable to the Holder with a Hook (#26). C.) Connect the Lat Bar (#25) to the Cable with a Hook (#26). When using the Lat P
Résumé du contenu de la page N° 10
STEP 6 (SEE Diagram 6) A.) To store the bench in a vertical position, remove the Arm Curl and the Lat Bar Frame from the bench and place them onto the storage posts on the Rear Upright Beams. B.) Pull out the 3” Lock Pin (#8) on the Main Seat Support to fold up the bench. Make sure to re-insert the Lock Pin on the bracket to secure the vertical position. DIAGRAM 6 9
Résumé du contenu de la page N° 11
10
Résumé du contenu de la page N° 12
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Rear Upright Beam 2 2 M10 x 2 3/8” Hex Bolt 5 3 ∅ ¾” Washer 16 4 M10 Aircraft Nut 8 5 1 5/8” x 3 1/8” Square End Cap 6 6 1 ¼” Square End Cap 2 7 Bracket 2 8 3” Short Lock Pin 1 9 ∅ 1” Round End Cap 7 10 Backrest Adjustment Bar 1 11 Bar Catch Panel 2 12 ∅ ¾” Bar Catch End Cap 2 13 Right Bar Catch 1 14 Left Bar Catch 1 15 Cross Brace 1 16 Backrest Support 2 17 1” Square End Cap 2 18 Backrest Board 1 19 Seat 1 20 M8 x 5/8”
Résumé du contenu de la page N° 13
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Custom
