Résumé du contenu de la page N° 1
1 1130SB 130SB
Owner's Manual / 96193004300 / 2008-11
Résumé du contenu de la page N° 2
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA
Résumé du contenu de la page N° 3
6. When cleaning, repairing or inspecting the snow thrower, Clearing a Clogged Discharge Chute stop the engine and make certain the collector/impel- Hand contact with the rotating impeller inside the discharge ler and all moving parts have stopped. Disconnect chute is the most common cause of injury associated with the spark plug wire and keep the wire away from the snow throwers. Never use your hand to clean out the dis- plug to prevent someone from accidentally starting the charge chute.
Résumé du contenu de la page N° 4
PARTS PACKED SEPARATELY IN CARTON (1) AUGER CONTROL ROD (1) TRACTION DRIVE CONTROL ROD (1) SAFTEY IGNITION KEY (35062) (1) POWER CORD (198563) (1) MULTI- WRENCH (1) DISCHARGE CHUTE (180684) EXTRA SHEAR BOLTS AND NUTS (6) SHEAR BOLTS 1/4-20 x 1-3/4 (6) SPACERS (6) LOCKNUTS (198636) (198638) 1/4-20 (73800400) ROTATOR HEAD MOUNTING (2) HANDLE KNOBS (3) RETAINER SPRINGS (169675) (2) CARRIAGE BOLTS (1) WASHER 3/8 (1) LOCKNUT 3/8 3/8-16 x 2.25 (19131316) (73800600) CHUTE DEFLECTOR REMOTE CONTROL (
Résumé du contenu de la page N° 5
ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the INSTALL TRACTION DRIVE CONTROL ROD chute rotator head to snow thrower and making ad just ments (See Figs. 3 and 4) to the skid plates. The traction drive control rod has the long loop on the end UNFOLD UPPER HANDLE of the spring as shown. 1. Raise upper handle to the operating position and 1. Slide rubber sleeve up rod and hook end of spring into tight en handle knobs securely. Additional carriage pivot bracket w
Résumé du contenu de la page N° 6
ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7) The auger control rod has the short loop on the end of the spring as shown. NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 1. Place discharge chute assembly on top of chute base with discharge opening toward front o
Résumé du contenu de la page N° 7
ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely. 3. Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown. SPRING 1/4-20 CHUTE SHOULDER DE FLEC TO
Résumé du contenu de la page N° 8
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Résumé du contenu de la page N° 9
OPERATION SPARK ENGINE OIL CAP AUGER DISCHARGE CHUTE CONTROL LEVER PLUG WITH DIPSTICK CONTROL DEFLECTOR SAFETY LEVER TRACTION DRIVE SPEED REMOTE IGNITION DRIVE CONTROL CON TROL LEVER KEY CONTROL GAS O LINE LEVER LEVER FILLER CAP CHUTE CHOKE DE FLEC TOR CON- TROL FUEL SHUT-OFF VALVE LH TURN TRIGGER THROTTLE / ENGINE CONTROL DISCHARGE CHUTE POWER LIGHT RECOIL CORD STARTER PLUG ELECTRIC HANDLE OIL DRAIN PLUG START HANDLE BUTTON CLEAN-OUT TOOL KNOB PRIM ER MUF FLER NOTE: ITEMS
Résumé du contenu de la page N° 10
OPERATION The operation of any snow thrower can result TO USE CHOKE CON TROL (See Fig. 13) in foreign objects thrown into the eyes, which The choke con trol is located on the en gine. Use the choke can result in severe eye damage. Always wear control when ev er you are starting a cold en gine. Do not safety glasses or eye shields while operating use to start a warm en gine. your snow thrower or performing any ad just- • To engage choke, turn knob clockwise. Slowly turn ments or repairs. W
Résumé du contenu de la page N° 11
OPERATION TO THROW SNOW (See Fig. 15) TO MOVE FORWARD AND BACKWARD (See Fig. 17) The auger rotation is controlled by the auger control lever SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control located on the right side handle. lever located on the left side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. • Squeeze traction drive control lever to handle to en gage the drive system. • Release the aug
Résumé du contenu de la page N° 12
OPERATION BEFORE STARTING THE ENGINE TO ADJUST SKID PLATES (See Fig. 19) NOTE: The wrench provided in your parts bag may be CHECK ENGINE OIL LEVEL (See Fig. 21) used to adjust the skid plates. The engine on your snow thrower has been shipped, from the factory, already filled with oil. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the 1. Check engine oil with snow thrower on level ground. ground surface. Adjust skid plates evenl
Résumé du contenu de la page N° 13
OPERATION 6. When the engine starts, release the recoil starter TO START ENGINE han dle and slowly move the choke control to the OFF • Be sure fuel shut-off valve is in the OPEN position. position. Your snow thrower engine is equipped with both a 120 Volt Allow the engine to warm up for a few minutes. Engine will A.C. electric starter and a recoil starter. The electric starter not develop full power until it has reached normal operat- is equipped with a three-wire power cord and plug and
Résumé du contenu de la page N° 14
MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. ➀ SAE 30 Motor Oil To receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some See “ENGINE” in ➁ ad just ments will need to be made periodically to properly Maintenance section maintain your snow thrower. General ➂ At least once a season, check to see if you should
Résumé du contenu de la page N° 15
MAINTENANCE BELTS TO CHANGE ENGINE OIL Check belts for deterioration and wear after every 50 hours Determine temperature range anticipated before next oil of operation and replace if necessary. The belts are not change. All oil must meet API service classification SG–SL. ad just able. Replace belts if they begin to slip from wear. • Be sure snow thrower is on level surface. (See “TO REMOVE BELT COVER” in the Service and • Oil will drain more freely when warm. Adjustments section of this manu
Résumé du contenu de la page N° 16
SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop. WARNING: To avoid serious injury, before performing any service or ad- 2. Remove safety ignition key and disconnect spark plug just ments: wire from spark plug. Place wire where it cannot come in contact with plug. 1. Be sure throttle is in STOP position. 3. Align holes in impeller hub with holes in impeller shaft 2. Remove safety ignition key. and install two (2
Résumé du contenu de la page N° 17
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 24) The auger and traction drive belts are not adjustable. If the HINT: Insert a 3/8" drive ratchet (in the “ON” position) into belts are damaged or begin to slip from wear, they should the square hole in idler arm and rotate ratchet clockwise be replaced. It is recommended that the belt(s) be replaced to relieve tension. by a qualified service center. 8. With tension relieved on idler, install new traction drive NOTE: It is recommended th
Résumé du contenu de la page N° 18
TO REMOVE WHEELS (See Fig. 25) NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts • Remove the klik pin and remove wheel from axle. dealer. Tire sealant also prevents tire dry rot and cor ro sion. IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the ENGINE hole in the wheel hub (if equipped). Inner hole in axle and See engine manual. hole in wheel hub are not used fo
Résumé du contenu de la page N° 19
TROUBLESHOOTING See appropriate section in manual unless directed to a qualified service centre. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Refill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position. 4. Move throttle to FAST position. 5. Choke in OFF position. 5. Move to FULL positio
Résumé du contenu de la page N° 20
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1 1130SB (96193004300), PRODUCT NO 130SB . 961 93 00-43 5 11 11 6 7 15 16 14 12 8 13 11 4 12 17 3 11 10 1 9 2 33 32 34 30 31 31 26 36 29 28 20 27 21 22 23 25 35 24 23 22 2 (EXPLODED) 21 19 18 01.07.004-B 20
