Résumé du contenu de la page N° 1
Operator’s manual & spare parts list.
It is the owner’s responsibility to ensure that all operators of this
machine have read and understood the content of this manual be-
fore using the product! Careless or improper use of this machine
can cause serious or even fatal injury! Allow only competent adults
to operate this machine!
K 750
SpeedMill
IPL, K750, 2007-01, 544 93 62-01
SpeedMill
K750
Reservdelar
Spare parts
Ersatzteile
Pieces de rechange
Piezas de repuesto
Ricambi
Peças sobress
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Section Page No. Section Page No. Table of Contents.............................................. 2 Uses................................................................... 7 Tools.................................................................. 7 Contact Information.......................................... 2 Symbols............................................................. 3 Assembly...................................................... 7 - 8 Intro
Résumé du contenu de la page N° 3
KEY TO SYMBOLS SAFETY SYMBOLS & DECALS Key to symbols Stop, in the fixed position. WARNING! The machine can be a Operator must wear head protection such as dangerous tool if used incorrectly or a hard hat! carelessly, which can cause serious or fatal injury to the operator or others. Other symbols/decals on the machine refer to special certification requirements for certain markets. Please read the operator’s manual carefully Operator must wear protective footwear such and make sure you un
Résumé du contenu de la page N° 4
SAFETY INSTRUCTIONS Safety Instructions: Introduction Thank you for purchasing your new machine from Husqvar- na Construction Products. We have provided important WARNING! safety messages in this manual and on the machine. Before starting up machine make sure you Please read these messages carefully. A safety message completely read these instructions and the alerts you to potential hazards that could hurt you or others. power cutter operation manual. Be familiar with operation of t
Résumé du contenu de la page N° 5
SAFETY INSTRUCTIONS WARNING! Read, understand, and follow all warnings and instructions in this and the K750 manuals. Failure to do so may result in serious personal injury as well as damage to the equipment. It is not possible to cover all possible risk situations that can arise in conjunction with pipe cutting and beveling within these instructions. Use common sense and caution at all times. Remember: “If you don’t know – don’t do.” The SpeedMill may not be modified from its original d
Résumé du contenu de la page N° 6
WHAT IS WHAT WHAT IS WHAT (PARTS IDENTIFICATION) F. 150mm (6”) SpeedMill Bowl: Designed specifically for A. SpeedMill BLADE GUARD: Designed specifically for the SpeedMill. Use for beveling 6” (150mm) plastic pipe. the SpeedMill. One side is open to allow mounting of the Read this Operation Manual for more information. See SpeedMill Bowls. Read this Operation Manual for more SpeedMill Spare Parts List in this document for part num- information. See SpeedMill Spare Parts List in thi
Résumé du contenu de la page N° 7
USES, TOOLS, AND ASSEMBLY Uses: Cutting and beveling of 100mm (4”), 150mm (6”), and 200mm (8”) PVC pipe of the following types; ASTM CAUTION! D2241 IPS Gasketed Pipe, and ASTM D3034 Gravity Always install the 8” SpeedMill Bowl (P/N 542 19 61- Sewer Pipe (Type SDR 35, and SDR 26). Note that this 89) before using the machine! The 8” SpeedMill must machine, as supplied, is not designed for cutting AWWA always be installed even if the machine will only be C900 Municipal Water Pipe, or any
Résumé du contenu de la page N° 8
ASSEMBLY AND OPERATION OPERATION: Mount the SpeedMill Bowl Assembly. Align the slot in the SpeedMill Hub with the face of WARNING! the shaft. Make sure the flange Before starting up machine make sure you face of the SpeedMill Hub con- completely read these instructions and the tacts the face of the blade. power cutter operation manual. Be familiar with operation of the machine before operation! Install the blade shaft bolt into the Hub Assembly. WARNING! EVACUATE PIPE CONT
Résumé du contenu de la page N° 9
OPERATION Rotate Pipe and repeat this cut- Align proper SpeedMill Bowl ting process until pipe circum- with end of pipe, and move ference is cut. toward the pipe so that the pipe is slightly beveled. Note: The bevel required is usually quite small, so do not remove excessive pipe mate- rial. Bevel Pipe: Position SpeedMill Bowl near end of pipe to be beveled. Accelerate power cut- ter to full throttle. WARNING! HOLD MACHINE ONLY at front and rear handles! NEVER bevel or cut
Résumé du contenu de la page N° 10
MAINTENANCE MAINTENANCE: CONVERTING THE SPEEDMILL TO A REGU- LAR POWER CUTTER. The guard on the SpeedMill is designed to work together CAUTION! with the special outer flange and SpeedMill Bowls used Allow SpeedMill Bowls to cool before performing any main- on the SpeedMill. The 8” (200mm) SpeedMill Bowl must tenance. always be installed when the SpeedMill is used and the SpeedMill shall not be used for any other purpose than NOTICE! those mentioned in “USES” section of this document. Sh
Résumé du contenu de la page N° 11
SPARE PARTS SpeedMill
Résumé du contenu de la page N° 12
115 07 95-27 SpeedMill 2007-10
