Résumé du contenu de la page N° 1
®
Installation and Operation Manual
For Hunter Ceiling Fans
41462-01 10/14/2005
1
41462-01 10/14/2005
Résumé du contenu de la page N° 2
® 41462-01 10/14/2005 2
Résumé du contenu de la page N° 3
® CONGRA CONGRA CONGRA CONGRA CONGRATULA TULA TULA TULA TULATIONS! TIONS! TIONS! TIONS! TIONS! Your new Hunter ceiling fan is an Model Name ___________________ addition to your home or office that Catalog No. ___________________ will provide comfort and perfor- Attach Your Receipt Serial No.______________________ mance for many years. This manual or a Copy of gives you complete instructions for Your Receipt Here Date Purchased _________________ installing and operating your fan. Where Purchased
Résumé du contenu de la page N° 4
® CONTENTS CONTENTS CONTENTS CONTENTS CONTENTS Important Information .......................................................................................................................... 5 Step 1 - Getting Ready .......................................................................................................................... 6 Step 2 - Installing The Ceiling Plate........................................................................................................ 8 Step 3 - Assem
Résumé du contenu de la page N° 5
® IMPOR IMPOR IMPOR IMPOR IMPORT T T T TANT INFORMA ANT INFORMA ANT INFORMA ANT INFORMA ANT INFORMATION TION TION TION TION CAUTIONS CAUTIONS CAUTIONS CAUTIONS CAUTIONS To reduce the risk of fire, let box and associated wall switch location. If you can- electrical shock, or motor Read entire booklet care- not lock the circuit breakers damage, do not use a solid- fully before beginning in- state speed control with this in the off position, securely stallation and save these fasten a prominent
Résumé du contenu de la page N° 6
® STEP 1 - GETTING READY STEP 1 - GETTING READY STEP 1 - GETTING READY STEP 1 - GETTING READY STEP 1 - GETTING READY GA GATHERING THE TOOLS THERING THE TOOLS GA GA GATHERING THE TOOLS THERING THE TOOLS THERING THE TOOLS Site” — to help you select the best Hint: If you are installing more than location for your fan. The booklet one fan, keep the fan blades You will need the following tools for also provides information to ensure in sets, as they were shipped. installing the fan: your fan support
Résumé du contenu de la page N° 7
® Standard Mounting Standard Mounting Angle Mounting Angle Mounting Standard Mounting Standard Mounting Standard Mounting (Figure 1a) Angle Mounting Angle Mounting Angle Mounting (Figure 1b) hangs from the ceiling by a connec- hangs from a vaulted or angled ceil- tor pipe (included), for ceilings 9 ing. feet or higher. For ceilings higher than nine feet, you can purchase Hunter extension rods. All Hunter fans use sturdy 3/4" diameter pipe to assure stability and wobble-free performance. 34 2
Résumé du contenu de la page N° 8
® STEP 2 - INST STEP 2 - INST STEP 2 - INST STEP 2 - INST STEP 2 - INSTALLING THE CEILING PLA ALLING THE CEILING PLA ALLING THE CEILING PLA ALLING THE CEILING PLA ALLING THE CEILING PLATE TE TE TE TE 1. Drill two pilot holes into the wood W W W W WARNING ARNING ARNING ARNING ARNING support structure through the To avoid possible electrical outermost holes on the outlet shock, before wiring fan, box. The pilot holes should be disconnect power by turn- 9/64" in diameter by 2 3/4" in ing off the
Résumé du contenu de la page N° 9
® Ceiling Joist For Angle Mounting Only For Angle Mounting Only For Angle Mounting Only For Angle Mounting Only For Angle Mounting Only: Be 5. Place a flat washer on each of the sure to orient the ceiling plate so two 3" screws and pass the screws 2 x 4 Brace that the arrows on the plate point through the slotted holes in the up towards the ceiling peak as ceiling plate as shown in Figure shown in Figure 2b. 2c. 6. Tighten the screws into the 9/64" pilot holes; do not use lubricants Ceiling Ceil
Résumé du contenu de la page N° 10
® STEP 3 - ASSEMBLING THE FAN STEP 3 - ASSEMBLING THE FAN STEP 3 - ASSEMBLING THE FAN STEP 3 - ASSEMBLING THE FAN STEP 3 - ASSEMBLING THE FAN 1. Insert the pipe through the hanger bracket and canopy as shown in Pipe Figure 3a. Feed wires from the fan through the pipe. Hanger 2. Screw pipe into fan assembly un- Bracket til tight. IMPORTANT! Tighten allen head pipe set screw as shown Canopy in Figure 3 with the included allen wrench. Allen Head Pipe Set Screw CAUTION CAUTION CAUTION CAUTION CAUTIO
Résumé du contenu de la page N° 11
® STEP 4 - HANGING THE FAN STEP 4 - HANGING THE FAN STEP 4 - HANGING THE FAN STEP 4 - HANGING THE FAN STEP 4 - HANGING THE FAN 1. Disconnect the power by turn- Note Note Note: T Note Note o remove the hanger Ceiling Plate ing off the circuit breakers to the bracket, while pressing the two outlet box and associated wall small releases on the ceiling switch location. plate, twist the hanger bracket counterclockwise. 2. Confirm that the three isolators are pre-installed on the hanger Hanger Bracke
Résumé du contenu de la page N° 12
® STEP 5 - WIRING THE FAN STEP 5 - WIRING THE FAN STEP 5 - WIRING THE FAN STEP 5 - WIRING THE FAN STEP 5 - WIRING THE FAN 3. Turn the connectors upward. Push W W W W WARNING ARNING ARNING ARNING ARNING W W W W WARNING ARNING ARNING ARNING ARNING the wires gently into the outlet To avoid possible electrical To reduce the risk of fire, elec- box. shock, before wiring fan, trical shock, or motor damage, disconnect power by turn- do not lift or carry the fan by ing off the circuit breakers the lea
Résumé du contenu de la page N° 13
® Black Power Wires In White Ceiling Bare or Green Outlet Box 2 x 4 Brace Green Ceiling Plate Approved Connectors Green Ground Wire from Hanger Pipe (not present with flush mounting option) Figure 5 - Wiring Diagram Figure 5 - Wiring Diagram Figure 5 - Wiring Diagram Figure 5 - Wiring Diagram Figure 5 - Wiring Diagram 41462-01 10/14/2005 13 White Black
Résumé du contenu de la page N° 14
® STEP 6 - ATT STEP 6 - ATT STEP 6 - ATT STEP 6 - ATT STEP 6 - ATTACHING THE CANOPY ACHING THE CANOPY ACHING THE CANOPY ACHING THE CANOPY ACHING THE CANOPY Refer to Figure 6. 1. Raise the canopy and align the holes in the canopy with the holes in the ceiling plate. 2. Install and tighten the three canopy screws. Figure 6 - Attaching Canopy to Ceiling Figure 6 - Attaching Canopy to Ceiling Figure 6 - Attaching Canopy to Ceiling Figure 6 - Attaching Canopy to Ceiling Figure 6 - Attaching Canopy to
Résumé du contenu de la page N° 15
® STEP 7 - ASSEMBLING FAN BLADES STEP 7 - ASSEMBLING FAN BLADES STEP 7 - ASSEMBLING FAN BLADES STEP 7 - ASSEMBLING FAN BLADES STEP 7 - ASSEMBLING FAN BLADES Blade Decorative 1. Attach each blade to the blade WARNING WARNING WARNING WARNING WARNING Screw iron using three barrel nuts and Failure to securely tighten the three decorative screws as shown 1/4"-20 Screws into the Motor in Figure 7a, 7b and 7c. Blade could cause the Blade Assem- Barrel Nut Iron bly to fall. Decorative Screw Blade Blade
Résumé du contenu de la page N° 16
® STEP 8 - ATT STEP 8 - ATT STEP 8 - ATT STEP 8 - ATT STEP 8 - ATTACHING THE SWITCH HOUSING ACHING THE SWITCH HOUSING ACHING THE SWITCH HOUSING ACHING THE SWITCH HOUSING ACHING THE SWITCH HOUSING The switch housing is made up of 2. Feed the two optional accessory CAUTION CAUTION CAUTION CAUTION CAUTION two sections: the upper switch hous- light kit wires with the attached Make sure the upper switch ing, and the lower switch housing. wire nuts through the center housing is securely attached to op
Résumé du contenu de la page N° 17
® A ATT TTACHING THE LOWER ACHING THE LOWER INST INSTALLING ALLING ACCESSOR ACCESSORY LIGHT Y LIGHT A A ATT TT TTACHING THE LOWER ACHING THE LOWER ACHING THE LOWER INST INST INSTALLING ALLING ALLING ACCESSOR ACCESSOR ACCESSORY LIGHT Y LIGHT Y LIGHT SWITCH HOUSING SWITCH HOUSING KITS KITS SWITCH HOUSING SWITCH HOUSING SWITCH HOUSING KITS KITS KITS 1. Place the lower switch housing To install an optional light kit, replace assembly over the upper switch the lower switch housing with the housing. M
Résumé du contenu de la page N° 18
® STEP 9 - REMOTE CONTROL STEP 9 - REMOTE CONTROL STEP 9 - REMOTE CONTROL STEP 9 - REMOTE CONTROL STEP 9 - REMOTE CONTROL REMOTE CRADLE INST REMOTE CRADLE INST REMOTE CRADLE INSTALLA ALLA ALLATION TION TION ROCKER LIGHT SWITCH ROCKER LIGHT SWITCH ROCKER LIGHT SWITCH WALL INST WALL INST WALL INSTALLA ALLA ALLATION TION TION REMOTE CRADLE INST REMOTE CRADLE INSTALLA ALLATION TION ROCKER LIGHT SWITCH ROCKER LIGHT SWITCH WALL INST WALL INSTALLA ALLATION TION 1. Break off the two tabs by push- 1. Loc
Résumé du contenu de la page N° 19
® BA BATTER TTERY INST Y INSTALLA ALLATION TION BA BA BATTER TTER TTERY INST Y INST Y INSTALLA ALLA ALLATION TION TION 3. Change the DIP switch settings, assuring that they are different 1. Slide the cover off the back of the from the previously installed fan. remote as shown in Figure 9d, Refer to Figure 9e. pressing in and sliding the cover down to release. 4. Replace the battery and cover. 2. Install the included 12 volt alka- 5. At the circuit breaker or fuse box, line battery (Type 23A, MN
Résumé du contenu de la page N° 20
® FAN CONTROL FAN CONTROL AIRFLOW DIRECTION AIRFLOW DIRECTION Do not turn the power off at the FAN CONTROL FAN CONTROL FAN CONTROL AIRFLOW DIRECTION AIRFLOW DIRECTION AIRFLOW DIRECTION circuit breaker , then back on, for the Refer to Figure 9f for identification of To reverse the airflow press the RE- previously installed fan(s), as you control buttons. VERSE button. Reverse operates at may inadvertently change the DIP any speed whether fan is on or off. To start the fan press the selected switc
