Résumé du contenu de la page N° 1
INSTRUCTION MANUAL
Petrol
Lawn
Edger
• Melbourne • Perth • Auckland • Hong Kong • Shanghai
PEDG
• Taipei • New York • Verona • London • Paris
050603 ED10 JJ
1
Résumé du contenu de la page N° 2
Contents Warranty 2 Full 2 Years Home Use Warranty Introduction 3 Whilst every effort is made to ensure your complete satisfaction with this tool, occasionally, due to the mass Description of symbols 3 manufacturing techniques, a tool may not live up to our Specifications 4 required level of performance and you may need the Safety instructions 4 assistance of our service department. This product is warranted for a 2-year period for home Additional safety rules for edgers 5 domestic u
Résumé du contenu de la page N° 3
Description of symbols Dear Customer The rating plate on your tool may show symbols. These If you require any help with your product, whether it represent important information about the product or is a Warranty claim, spare part or user information, instructions on its use. please phone our Help Line for an immediate response. Phone 1300 880 001 in Australia or 0800 445 721 in Wear hearing protection. New Zealand. Wear eye protection. Wear breathing protection. Introduction Conforms to r
Résumé du contenu de la page N° 4
Personal safety Specifications • Stay alert, watch what you are doing and use Engine: 26cc, 2 Stroke common sense when operating a power tool. Do -1 Speed: 0 - 2200min not use a power tool while you are tired or under the Depth of cut: 10mm, 20mm, 30mm influence of drugs, alcohol, or medication. A moment of Size of blade: 180mm inattention while operating power tools may result in serious personal injury. Bore size: 18mm • Use safety equipment. Always wear eye protection. fuel type
Résumé du contenu de la page N° 5
• Ensure the tool is switched off completely before • B lade fracture. making any adjustments, changing accessories, or • Catapulting of blade pieces. storing power tools. Such preventive safety measures • Damage to hearing if effective earmuffs are not worn. reduce the risk of starting the power tool accidentally. • Do not use blades that are deformed or cracked. • Store idle power tools out of the reach of children and • Do not operate in a hazardous location. Such areas do not allow pe
Résumé du contenu de la page N° 6
• Keep hands clear of edge guide and blade when • U se only blades as recommended. cleaning as these wear to a very sharp point during • Do not attempt to free a jammed blade before first edging. switching off the machine. • Before landscaping or trenching, inspect and ensure • L et the blade come to rest naturally. there are no exposed or buried cables or pipes or other • Periodically check that all fixings are properly tightened. objects that may create a hazard or interfere with o
Résumé du contenu de la page N° 7
3 Know your product 4 1. Lock off button 1 2. Throttle trigger 2 8 3. Ignition switch 4. Auxiliary handle 5. Shaft 6. Edger guide lever 5 7. Wheel 8. Auxiliary handle lock knob 9. Height adjustment knob 10. Guide wheel 11. Blade cut indicator 12. Fuel tank 18 13. Recoil starter 14. Primer bulb 15. Spark plug 16. Air filter cover 17. Choke lever 6 18. Shaft height adjustment knob 15 19. Air filter cover locking knob 16 19 12 11 7 13 17 10 9 14 7
Résumé du contenu de la page N° 8
4. Unscrew the fuel tank cap and pour the mixture into Assembly the tank. Inserting the shaft Remove the nut from the hole in the base of the edger 4a 4b and insert the shaft. Replace the nut and retighten it. Telescope handle adjustment The shaft handle can be set at three different heights. To set the height for your comfort, slide the tube up to the level required using one of 5. Be careful not to spill any mixture. If this happens, wipe the three holes provided and the spill wit
Résumé du contenu de la page N° 9
Starting the edger Stopping the edger 4 Choke control Stop the engine by pressing the off button (3) to the off position Start position (choke closed). marked 0. Run position (choke open). To start the engine, proceed as follows: 1. Move the ignition switch (3) to the on position marked Running in the engine with an I. 1. During the first ten hours of work, run the engine at a 2. Press the primer bulb (14) 6 moderate RPM. 2 times until there are no air 2. We advise you in any case no
Résumé du contenu de la page N° 10
outwards. Rotate the knob in a clockwise direction until 3. The guard is fitted with a 3 all of the slack is taken out of assembly. raised rib section which acts as a blade cut indicator (11). 4. Check to ensure the front wheel arm has located into This rib will assist in guiding one of the pre allocated positions and the head of the the operator where the blade bolt securing the front wheel arm is sitting flat on the will cut. During operation the surface of the wheel arm. Firmly tight
Résumé du contenu de la page N° 11
Warning. The unit may become very hot during use. Ensure the assembly is correct Avoid contact during and immediately after operation. and the blade is correctly orientated by checking the Landscaping / trenching diagram below. Before landscaping or trenching, inspect and ensure there With the spanner fitted to the are no exposed or buried cables or pipes or other objects outer flange, fit the locking that may create a hazard or interfere with operating the nut and tighten with the blade
Résumé du contenu de la page N° 12
• Remove air filter cover (16) Storage and maintenance after use by turning the air filter locking • When you finish working, clean the petrol edger knob (19) anti-clockwise and completely, making sure there is no grass or dirt removing the cover as you do wrapped in the cutting tools, and put it back into its carefully remove the Air intake package in order to avoid its hurting you or other people tube so that you can access during transport. the filter. • Be aware to not hit or cut t
Résumé du contenu de la page N° 13
13
Résumé du contenu de la page N° 14
14
Résumé du contenu de la page N° 15
15
Résumé du contenu de la page N° 16
Carefully read the entire Instruction Manual before using this product. With continuing product development changes may Before returning this product for a have occurred which render the product received Warranty Claim or any other reason slightly different to that shown in this instruction Please Call 1300 880 001 (Australia) manual. The manufacturer reserves the right to or 0800 445 721 (New Zealand) change specifications without notice. Note: Specifications may differ from country to
