Résumé du contenu de la page N° 1
Grill Assembly
Built-In Instructions
5-12
13-15
16-19
17
20
21-22
23
Résumé du contenu de la page N° 2
Welcome & Congratulations Congratulations on your purchase of a new gas grill! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the best service possible. Your satisfaction is our number one priority. We know you’ll enjoy your new gas grill and Thank You for choosing our product. We hope you consider us for future purchases. PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS This Use & Care Manual provides specific operating instr
Résumé du contenu de la page N° 3
General Safety Instructions IMPORTANT SAFETY INFORMATION - Read this manual carefully before using your grill to reduce the risk of fire, burn hazard or other injury. - Extreme care should be used because of the high temperatures produced by this appliance. CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA WHERE THE GRILL IS BEING OPERATED. - This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and liquids. Do not allow flammable materials to come
Résumé du contenu de la page N° 4
Grill Features: FD30 7 1 8 2 9 13 3 14 4 10 5 12 11 6 1. Roll top grill hood 8. Warming shelf 2. Grilling/Cooking surface 9. Infrared back burner 3. Side Shelf 10. Electronic ignitor: main, rear infrared & side burner 4. Control knob: back infrared burner 11. Cart w/doorr 5. Control knobs: main burners 12. Ignitor access opening 6. Convection vents 13. Side Burner 7. Handle 14. Control knob: Side Burner 3
Résumé du contenu de la page N° 5
Grill Components List Cart Parts Part #’s 2 L-shaped side pieces WIP-192-71D384 1 U-shaped back side piece WIP-192-72D384 1 Base WIP-192-70D304 2 Wheel channels WIP-192-438365L/R Cart Door Parts 1 Door handle kit RMP-122-00921 1 Nylon bushing RMP-122-00520 1 Door pivot screw and nut RMP-122-00598/122-00508 Grill Parts Grill Parts 1 Stainless steel grill head WIP-122-11D304 1 Stainless steel side shelf WIP-192-326393 1 Side burner (side shelf) WIP-191-43DGN4 1 Electronic ignitor RMP-122-53306 5
Résumé du contenu de la page N° 6
Grill Assembly Note: Prior to assembly remove protective film from stainless steel parts Assembly requires: 4 tools and a Friend Tools required: Power screwdriver Screwdriver extension 1/4” socket wrench Screws Fig. 1 1/2” socket wrench adjustable wrench scissors Caution: Gas regulator is not flush with Wheel Channel bottom. DO NOT let the Grill head sit flat without placing support around regulator to prevent damage to the regulator prior to installing on cart. Door Stop Fig. 2 Hole Cart A
Résumé du contenu de la page N° 7
Grill Assembly Attaching Grill Head to Cart 1. While keeping the Grill on the foam base Screw hole for lean it onto its back. (be sure to hold the magnetic catch hood shut when doing this.) With the Grill on its back, loosen all 4 bolts on the bottom side of the Grill, but do not Fig. 5 remove.(See Fig. 5) Bolts 2. Using 2 self tapping hex head screws, attach the magnetic door catch in the 2 holes in the bottom of the grill. (See Fig. 6) 3. Have someone help you pick up the grill and se
Résumé du contenu de la page N° 8
Grill Assembly Installing the Cart Door Handles 1. Using a 5/32” allen wrench insert 1 screw through the inside of the door front into a bar handle end and tighten securely. (See Fig. 9) 2. Insert Bar Handle into the End Cap Backside of door: attached to the door and then into the 2 screw locations other End Cap and tighten End Cap with allen wrench and screw. (See Fig. 10) 3. Complete Door. (See. Fig. 11) Screw Holes Fig. 9 End Cap Installing the Drip Tray End Cap 1. The drip pan is ins
Résumé du contenu de la page N° 9
Grill Assembly Side Shelf Attachment Shelf Hooks 1. Attach the shelf to the left side of grill by inserting the shelf hooks into the slots on the Fig. 13 side of the grill and pushing down on the shelf assembly until level with grill. (See Fig. 13) 2. Lock the shelf in place by inserting (2) self taping screws into shelf. (See Fig. 14) Interior parts installation Fig. 14 1. Check to make sure the bottom Flavor Grids are correctly installed in the cutouts and around the ignitors, as they ma
Résumé du contenu de la page N° 10
Side Burner Assembly 1. Attach the Side Burner to the grill by inserting the shelf hooks into the slots on the side of the grill and pushing down on the shelf Fig. 19 assembly until level with the grill (See Fig. 19) 2. Lock the Side Burner in place by re-inserting (2) hex head screws in the front & rear edge of side burner. (See Fig. 20) Note: A power screwdriver extension is needed to insert screw. Fig. 20 3. Attach the Flex Line coming from the side of the grill to the fitting on the
Résumé du contenu de la page N° 11
Side Burner Assembly SIDE BURNER PARTS ASSEMBLY Install grate over burner (See Fig. 23) LEAK TESTING Make sure all burners are turned to “OFF”. Turn on the gas at the cylinder (LP models) or main valve (Natural models). DO NOT turn on the side burner. Perform a leak test at all connections and fittings by spraying a 50/50 solution of water and soap. If any bubbles appear, correct the leak before Fig. 23 attempting to light the grill or side burner. IGNITOR ASSEMBLY 1. The Battery, Spring an
Résumé du contenu de la page N° 12
Built-In Instructions The Frigidaire Grill can be installed as a built-in Grill. If installed as a built-in Grill, the Grill surround must be constructed of Non-combustible material. Planning and Design Start by identifying the number and size of components you want to include: Grill, side burner, access doors for storage or other items you may wish to furnish such as: refrigerator, sink, warming drawer. Countertops must be constructed with non-combustible, outdoor-safe materials. Consider
Résumé du contenu de la page N° 13
Built-In Instructions Side cutout is needed on left side to feed ignitor wire Note: Make sure to use a to the ignitor plate (26” model only) non-combustible base and sides for the structure (Size: 10” high x 5” long, set 1” back from front edge) 1 27 /2” Min. GFI Electrical outlet for rotisserie motor A (6.5 amp min.) *Gas Cutout C Floor Support B 2” area for grill 1 35 /2” Max. Opening for IGNITOR PLATE access door(s) INSTALLATION D *Required Ignitor cutout counter top for front or side mou
Résumé du contenu de la page N° 14
Gas Requirements General Information Verify the type of gas supply to be used, either Natural Gas (NG) or Liquid Propane (L.P)., and make sure the marking plate (located on the back of the unit) agrees with that of the supply. Note: Never attach an unregulated gas line to the appliance. For Natural Gas installations, an installer must supply a gas shutoff valve that is easily accessible to the grill. All installer supplied parts must conform to local codes, or in the absence of local codes, wi
Résumé du contenu de la page N° 15
Gas Requirements L.P. Gas Installation Frigidaire Gas Grills that are set to operate with L.P. gas come with a high capacity hose and regulator assembly. (Note: Only use the pressure regulator and hose assembly supplied with the grill or a replacement pressure regulator and hose assemblies specified by Frigidaire). This assembly is designed to connect directly to a standard 20 lb. L.P. cylinder. Attach the gas hose assembly to the brass 3/8 flared fitting using an adjustable wrench on the un
Résumé du contenu de la page N° 16
Leak Testing General Information Although all gas connections on the grill are leaked tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive pressure unknowingly being applied to the unit. Periodically check the whole system for leaks, or immediately check if the smell of gas is detected. Before Testing Do Not smoke while leak testing. Extinguish all open flames. Never leak test
Résumé du contenu de la page N° 17
Using the Grill Grill Location Do not use the grill in garages, breezeway, sheds or any enclosed area. Never operate the grill in enclosed areas as this could lead to a carbon monoxide buildup, which could result in injury or death. Place the grill on a level surface. Avoid moving the grill while it is operation. Note: The grill will operate best if it is not facing directly into the wind. Clearance to combustible construction - A minimum of 12” from the sides and back must be maintained fr
Résumé du contenu de la page N° 18
Lighting the Grill Before Lighting Warning: Important! Before Lighting... Check the gas supply line for cuts, wear or abrasion. Do not attempt to Always keep your face and body as far away from the “Light” the grill if the grill as possible when lighting. odor of gas is present!! Grill Burner Lighting Lighting the Grill with electronic ignitor Always open the lid before attempting lighting. Push and turn one of the control knobs counter clock- wise to the “HIGH” position and immediately pre
Résumé du contenu de la page N° 19
Using the Rotisserie & Side Burners (Optional ROTISSERIE KIT to use with Back Infrared Burner must be purchased separately) The grill rotisserie system is designed to cook items from the back using infrared heat. The rotisserie burner is an infrared type which provides intense searing radiant heat. Preferred by chefs over other cooking methods, this intense heat is magnificent for searing in the natural juices and nutrients found in quality cuts of meats. Once lit, the rotisserie burner will re
Résumé du contenu de la page N° 20
Using the Rotisserie & Side Burners Rotisserie Lighting Open the lid. Push and turn the control knob counter clockwise to the “HIGH” position. Wait 5 seconds. Then press and hold the electronic ignitor button. You’ll hear a snapping sound. If the burner does not light in 4 seconds, turn the control knob to OFF and wait 5 minutes before trying again. Once lit, turn the control knob to the desired setting. (See Fig. 27) (If the ignitor does not function, the burner can be lit by holding a lit
