Résumé du contenu de la page N° 1
Chipper/Shredder with 2-Way Feed
Owner’s Manual
This manual contains important safety instructions for
Chipper/Shredder models: CH2, CH7
READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY
SAVE THESE INSTRUCTIONS.
Do not return this unit to the store!
For product questions or service,
CALL 1-919-550-3259
or go to www.gxioutdoorpower.com
When you call the help-line you will need to have the following information:
Date of Purchase: _______________________
Location of Purc
Résumé du contenu de la page N° 2
Copyright© 2012 by GXi Outdoor Power, LLC. All rights reserved. No part of this publication can be reproduced or distributed without prior written permission of GXi Outdoor Power, LLC Clayton, NC 27520 USA. STANLEY is a registered trademark of The Stanley Works or its affiliates and are used under license by GXi Outdoor Power LLC. GXi Outdoor Power, LLC reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation wha
Résumé du contenu de la page N° 3
Contents Warnings ............................................................................................................ 1 Product Specifications ........................................................................................ 2 Component Identification ................................................................................... 3 Missing Parts Order Form................................................................................... 4 Identification Component .......
Résumé du contenu de la page N° 4
Warnings WARNING WARNING This symbol indicates important safety instructions which, if not followed, could endanger personal safety and/or property. Read and follow all instructions in this manual before attempting to Keep bystanders, helpers, pets, and children at least 75 feet from the operate this machine. Failure to comply with these instructions machine while it is in operation. Stop machine if anyone enters the may result in personal injury. When you see thi
Résumé du contenu de la page N° 5
Warnings 7. Do not put hands or feet near rotating parts or in the feeding Training chambers and discharge opening. Contact with the rotating 1. Read, understand, and follow all instructions on the machine and impeller can amputate fingers, hands, and feet. in the manual before attempting to assemble and operate. Keep 8. Never attempt to unclog either the feed intake or discharge this manual in a safe place for future and regular reference and opening, or inspect and repair the mach
Résumé du contenu de la page N° 6
Component Identification Leaf Funnel Discharge Chute Use the Leaf funnel to feed leaves Chipped materials are discharged and branches no larger than 1/4” through this opening. only. Limb Chute Fuel Tank Use the Limb chute to feed longer Use regular unleaded fuel. Always leave and/or thicker pieces of yard waste about 1” of air gap at the top of the tank into the impeller for chipping. for fuel expansion to prevent seepage or Depending on the model #, the spills. chipper
Résumé du contenu de la page N° 7
Missing Parts Request Form Please indicate the part that you are missing: Name Address Date of purchase Model #: CH2 Phone CH7 Email Serial #: Comments: IMPORTANT: Please include your receipt. Without a receipt, your order will be delayed. You may also email us at: customerservice@gxioutdoorpower.com. If emailing, please scan in your proof of purchase. Refer to parts diagram and part list on page 5 and 6 for part numbers. This will expedite the process. STANLEY is a r
Résumé du contenu de la page N° 8
Component Identification STANLEY is a registered trademark of The Stanley Works or its affiliates and are used under license by GXi Outdoor Power LLC. No part of this publication can be printed or copied without written permission. Rev2.5-15-12 5
Résumé du contenu de la page N° 9
Component Identification STANLEY CH2 Chipper Shredder Spare Parts Diagram Item # GXi Part Number Description 1 LCSSP11-001 Chipper, plastic leaf funnel assembly kit with hardware and label for STANLEY 2 LCSSP11-002 Chipper, discharge deflector with hardware and label 3 LCSSP11-003 Chipper, STANLEY yellow, limb chute, 2.25" capacity, with hardware and label 4 LCSSP11-004 Chipper, hardware kit, engine fasteners with engine shaft key 5 LCS12-125 Engine assembly, 208cc, black paint, labels for
Résumé du contenu de la page N° 10
Safety Information Your Responsibility Restrict the use of this chipper/shredder to persons who read, understand and follow the warnings and instructions in this manual and on the machine. Note: Not all safety labels shown may apply to your chipper/shredder. heater, clothes dryer, etc.). Preparation j. To reduce the fire hazard, keep machine free of grass, 1. Thoroughly inspect the area where the chipper/shredder is to be leaves, or other debris build-up. Clean up oil or fuel
Résumé du contenu de la page N° 11
Operating Guidelines READ THESE OPERATING GUIDELINES BEFORE YOU PROCEED ANY FURTHER 1. Do not put hands and feet near rotating parts or in the feeding The side chute is for chambers and discharge opening. Contact with the rotating longer and/or thicker impeller can amputate fingers, hands, and feet. pieces of yard waste. Depending on your mod- 2. Before starting the machine, make sure the chipper chute, feed el, you may chip to your intake, and cutting chamber are empty and fr
Résumé du contenu de la page N° 12
Assembly 1 2 3 6 4 5 Figure 1 IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be 1. Remove the chipper from its carton certain to fill the engine with gasoline and oil as instructed before operating Remove plastic banding and cut the tape on the top of the box. your machine. 2. Remove the shipping frame (item 6) from item 1 above The steel shipping frame (item 6) is banded to the base of the chipper at Required tools: Two 13mm wrenches the eng
Résumé du contenu de la page N° 13
Assembly 5. Disconnect The Spark Plug Wire Before setting up your chipper shredder, disconnect the spark plug wire from the spark plug and ground against the engine to prevent inadvert- ent starting of the machine. This step should be taken as a precaution whenever you are working on this machine. 6. Attaching the chipper discharge chute (Figure 3) Place discharge chute over rectangular opening on the chipper body. The plastic discharge chute fits on the outside of the steel
Résumé du contenu de la page N° 14
Important Engine Information NOTE: The chipper/shredder operates most efficiently at the factory set engine speed of 3600 RPM. The speed is WARNING controlled by the governor, and the throttle setting should not be adjusted. Do not attempt to adjust the speed of the engine. Carbon Monoxide Gas Exhaust contains poisonous carbon monoxide, a colorless and Emission Control System Information odorless gas. Breathing exhaust can cause loss of consciousness and The U.S. an
Résumé du contenu de la page N° 15
Operating Instructions Rapid retraction of the recoil starter cord can pull the starter cord back faster than you can let go. When starting the engine, DANGER pull the cord slowly until resistance is felt then pull rapidly to avoid kickback. This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, NOTE: A noise will be heard when finding the start of the carelessness or error on the part of the ope
Résumé du contenu de la page N° 16
Maintenance and Storage Maintenance Schedule 20 hrs or Before each 50 hrs or eve- 100 hrs or eve- 300 hrs or Item every 3 use ry 3 months ry 6 months every 1 year months Check for loose fasteners (check) X Engine Oil (Check) X Engine Oil (Change) X Air Cleaner (Check) X Air Cleaner Wash X Fuel filter Cup (Clean) X Spark Plug (Clean) X Spark Plug (Change) X Check Chipper Blade X Fuel Tank and Filter (Clean) X 7. Never store the machine
Résumé du contenu de la page N° 17
Maintenance and Storage WARNING Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. Removing and Sharpening the Limb Chute Blades The chipper was shipped with two blades attached spare blades are sold in sets from GXi (Part Number LCSSP11-018) 1. Disconnect the spark plug wire and ground against the engine. 2. Remove limb chute by removing the four nyloc nuts that attach the li
Résumé du contenu de la page N° 18
Maintenance and Storage WARNING Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. Removing and Sharpening the Leaf Funnel Blade 1. Disconnect the spark plug wire and ground against the engine. 2. Remove the lower section and upper section of the funnel as a subassembly. This is done by removing three bolts with the 13mm wrenches provided in the hardwar
Résumé du contenu de la page N° 19
Troubleshooting Problem Cause Remedy 1. Spark plug wire disconnected. 1. Connect wire to spark plug. Engine fails to start 2. Fuel tank empty or stale fuel. 2. Fill tank with clean, fresh gasoline. 3. Throttle control lever not in correct starting 3. Move throttle lever to FAST position. position. (If equipped) 4. Choke not in CHOKE position. (If equipped) 4. Move choke to CHOKE position. . 5. Engine not primed. 5. Prime engine. 6. Blocked fuel line. 6. Clea
Résumé du contenu de la page N° 20
Limited Warranty and Service Length of Warranty: *(from the date of original retail purchase) Products Covered by this Warranty Noncommercial/ Commercial Rental Nonrental Engine 12 months 3 months 3 months *Length of Warranty: Consumable parts such as oil, spark plugs, filters, blades, and belts are not covered by this warranty. Warranty repairs will be made without charge for parts and labor for the first 6 months. After the first 6 months, the limited warranty covers the costs of
