Résumé du contenu de la page N° 1
Jeep
®
• • P Please read this manual and lease read this manual and
save it with your original save it with your original
sales receipt. sales receipt.
• • Tools needed for assembly: Tools needed for assembly:
Phillips Screwdriver and Safety Phillips Screwdriver and Safety
S Scissors (both not included). cissors (both not included).
• • Use only with the included Use only with the included
P Power Wheels ower Wheels® ® 12 Volt Lead-Acid, 12 Volt Lead-Acid,
Rechargeable, orange Battery R
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Warnings and Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 3
ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery retainer. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could cause overheating, fire
Résumé du contenu de la page N° 4
PARTS • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Rear Clip Brush Guard Vehicle 2 Rear Wheels
Résumé du contenu de la page N° 5
Steering Wheel Cap Steering Wheel 2 Side Mirrors (Left and Right) Rear Grille Key 4 Hubcaps 2 Wheel Steering Column Retainers Rear Axle 4 Front Steering Axle Caps Column Cap 12 Volt Charger 12 Volt Orange Battery Part Not Shown: Label Sheet - 2 #8 x ¾" Screw - 53 " x 1½" Pin - 1 Fasteners Shown Actual Size For your convenience, we included extra fasteners! Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. 5 N2273pr-0920
Résumé du contenu de la page N° 6
PARTS PICTURE Note: Some parts shown are assembled to both sides of the vehicle. 24 25 15 24 10 9 14 13 17 22 5 8 11 16 4 1 11 12 6 11 18 12 11 21 20 21 19 20 2 23 7 3 25 Long Seat Belt 1 Vehicle 9 Seat Bar 17 Steering Column 2 Front Grille 10 Rear Grille 18 Wheel Retainer - 2 Parts Not Shown 3 Brush Guard 11 Fender - 4 19 Steering Column Cap 2 Label Sheets 4 Rear Clip 12 Side Mirror - 2 20 Front Axle Cap - 4 #8 x ¾" Screw - 53 5 Rear Bumper 13 Steering Wheel 21 Hubcap - 4 6 Rear Wheel - 2 1
Résumé du contenu de la page N° 7
BATTERY CHARGING ELECTRICAL HAZARD About Thermal Fuses ® WARNING Your Power Wheels 12 volt orange battery is equipped with a built-in thermal fuse. The thermal fuse is a self-resetting safety device which • Battery can fall out and injure a child if automatically “trips” and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe. Once vehicle tips over. Always use battery retainer. a fuse has "tripped", remove your foot from the pedal and wait
Résumé du contenu de la page N° 8
ASSEMBLY WARNING Children can be harmed by small parts, sharp edges and sharp points in the vehicle's unassembled state, or by electrical items. Orange Care should be taken in unpacking and B Battery assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. A Charger Connector A • Plug the charger connector into the battery . B • Plug the charger into a standard wall outlet . Notes: - Use the charger only in a wall out
Résumé du contenu de la page N° 9
Motor Harness Connector Rear Clip 4 REAR VIEW • Pull the motor harness connector through the opening in the rear clip and into the trunk. 2 • Fit the rear clip onto the rear end of the vehicle and over the rear bumper. • Make sure the tabs on each side of the rear clip fit into the sides of the vehicle. • “Snap” the sides of the rear bumper into the openings on each side of the rear clip. Trunk Lid 5 TOP VIEW • Insert two screws into the trunk and tighten. • Replace the trunk lid. Rear Gril
Résumé du contenu de la page N° 10
Seat Bar Short Seat Belt Seat Long Seat Belt Seat 8 7 • Fit the seat bar to the back of the seat. • Insert four screws through the seat bar and into the seat. • Insert the "T" fastener end of a short seat belt strap up Tighten the screws. through the slot near the outer edge of the seat. Make sure the fastener side of the seat belt faces inward. Note: You will pull only one T-Loop through the slot. • Repeat this procedure to assemble the other short seat belt strap. • Insert each fastener e
Résumé du contenu de la page N° 11
T TOP VIEW TOP VIEW OP VIEW SIDE VIEW 10 • Insert four screws through the seat bar and into the vehicle. Tighten the screws. 9 • Insert the tabs on the front edge of the seat into the slots inside the vehicle. INSIDE VIEW 11 • Insert a screw into the hole in the console between the seats. 11 N2273pr-0920
Résumé du contenu de la page N° 12
4 Front Grille 1 3 Brush Guard 2 12 TOP VIEW 14 • Fit the front grille to the grooves in the top of the brush guard, as shown. • Fit the four fenders marked 1, 2, 3 and 4, to the vehicle, • Inset three screws through the front grille and into the brush as shown. guard. Tighten the screws. Hint: The fenders are designed to fit the vehicle one way. • Make sure the peg on the inside edge of each fender fits into the lower hole inside each wheel well. FRONT VIEW 13 15 • Fit the front grille assem
Résumé du contenu de la page N° 13
Steering Column Steering Column Cap Steering Column 18 FRONT BOTTOM VIEW INSIDE VIEW 16 • Fit the steering column cap onto the end of the steering column. • Wipe the steering column with a paper towel to remove any excess lubricant. • Insert the curved end of the steering column down through the opening in the dash and then down through the hole in the vehicle floor. Hint: You may need to turn the steering column to fit it through both openings. Steering Linkage Steering Column 19 • Insert a
Résumé du contenu de la page N° 14
Front Axle Post Front Axle Cap 22 Wheel Well • Fit a front axle cap onto the front axle post and hold it in place. • Insert a screw through the large opening in the front axle cap Fender and the hole in the front axle. Tighten the screw. 20 • Repeat this procedure to fasten the bottom of the other front axle. • Insert a screw through each wheel well and into each fender. Tighten the screws. "Lug Nuts" Front Axle Slot Front Wheel 23 Front Axle 21 Note: There are front and rear wheels. The rear
Résumé du contenu de la page N° 15
Front Axle Cap Rear Axle 24 REAR BOTTOM VIEW 26 • Fit a front axle cap onto the end of the front axle. • Slide the rear axle through the large opening near the rear of the vehicle, as shown. 25 "Lug Nuts" • Insert a screw through the large opening in the front axle cap Rear Wheel and the hole in the front axle. Tighten the screw. 27 • Repeat this procedure to attach the other front wheel to the other front axle. • Place a rear wheel onto the rear axle with the “lug nuts” facing out. • Turn th
Résumé du contenu de la page N° 16
Wheel Retainer Steering Column Steering Wheel Tab 28 • Fit a wheel retainer onto the end of the rear axle. 31 INSIDE VIEW • Position the steering wheel so that the tab is upright. • Fit the steering wheel onto the end of the steering column. 5 5 / /3 32 32 2" x 1½" Pin " " x 1½" Pin x 1½" Pin Press Wheel P Press Wheel ress Wheel 29 • Insert a screw through the large opening in the wheel retainer and the hole in the rear axle. Tighten the screw. • Push the axle into the wheel as far as it will
Résumé du contenu de la page N° 17
Steering Wheel Cap Post Side Mirror Recessed Area 33 • Fit the steering wheel cap onto the center of the steering wheel. • Insert two screws into the steering wheel cap and tighten. Right Side Mirror SIDE VIEW 35 • Position the right side mirror with the recessed area facing up, as shown. • “Snap” the right side mirror onto the post on the right side of the vehicle. • Turn the mirror upright. 34 • Pull up on the steering wheel to be sure it is assembled correctly. If you can remove the steer
Résumé du contenu de la page N° 18
1.5V x 4 "C" (LR14) Battery Safety Information In exceptional circumstances batteries may leak fluids that can cause a chemical burn injury or ruin your toy. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the toy. Dispose of batt
Résumé du contenu de la page N° 19
DECORATION • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles. 6 19 4 6 12 13 1
Résumé du contenu de la page N° 20
15 18 15 15 10 11 2 16 19 9 8 12 14 17 1 8 12 BACK VIEW 7 SIDE VIEW 20 N2273pr-0920
