Résumé du contenu de la page N° 1
™
Product features may vary from the picture above.
Please read this manual and save it with your original sales receipt.
Tools needed for assembly: Phillips Screwdriver, Hammer and Safety Scissors (all not included).
®
Use only with a Power Wheels 6 Volt Rechargeable Battery with A-style Connector and
®
™
Built-in Thermal Fuse and a Power Wheels Super 6 Volt Charger (both included).
JEEP and the Jeep grille design are registered
trademarks of DaimlerChrysler Corporation and are
used used unde
Résumé du contenu de la page N° 2
Table of Contents A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Résumé du contenu de la page N° 3
Warnings and Cautions B ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could cause over
Résumé du contenu de la page N° 4
Parts C • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. •Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Wheel - 4 Vehicle Body Hubcap - 4 Seat Hood La
Résumé du contenu de la page N° 5
Parts Steering Wheel Roll Bar Steering Wheel Cap Brush Guard Steering Linkage Front Axle - 2 Hood (Located in motors in back end of vehicle body.) Steering Column Rear Axle 5
Résumé du contenu de la page N° 6
WARNING • D o nPREVEN o t b y p a s s T FIRE a P o w e r W h e e l • U s e o n l y a R e d P o w e r W h e e ls •OR OPERA N e v e r m o d i fyT tE h e e l e c t r i c a l Parts Bushing - 2 Spacer - 2 Long Bushing - 2 Assembly Tool ™ Super 6 Volt Charger 6 Volt Battery Not Shown: Label Sheet - 2 *Note: For your convenience, we have included two extra cap nuts, and one extra washer and 1" screw. .437" #10 x 1" Screw - 8* .437 Cap Nut – 8* Washer - 4* #8 x 1" Screw - 2 #8 x 4" Screw - 2 Fasteners S
Résumé du contenu de la page N° 7
Parts Diagram D 14 15 3 16 19 13 17 2 23 22 19 19 24 11 9 8 10 25 4 1 5 12 11 24 25 19 7 18 18 19 4 20 20 4 8 21 18 19 6 19 6 18 Hint: Some parts shown are assembled on both sides of the vehicle. ™ 1. Vehicle Body 11. Hood Latch - 2 21. Super 6 Volt Charger 2. Dashboard 12. Brush Guard 22. 6 Volt Battery 3. Windshield 13. Steering Column 23. Asembly Tool 4. Hubcap - 4 14. Steering Wheel 24. Long Bushing - 2 5. Driver - 2 15 Steering Wheel Cap 25. Spacer - 2 6. Front Axle - 2 16. Roll Bar Not Sho
Résumé du contenu de la page N° 8
Battery Charging E About Thermal Fuses ELECTRICAL HAZARD Your Power Wheels 6 volt battery with A-style connector is equipped with a built-in thermal fuse. The thermal fuse WARNING is a self-resetting safety device which automatically “trips” and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe. Once a • Battery can fall out and injure a child if fuse has “tripped”, it will automatically reset itself after vehicle tips over. Always use battery
Résumé du contenu de la page N° 9
WARNING • D o noPR t bEyVEN p as s T a P FoIR w e r W E h e e l • U se on ly a R ed P o w e r W h ee l s •OR Ne ve OP r mER o diAT fy th E e ele ct ri c a l Battery Charging 1 Battery 3 Compartment Battery Clamp • Plug the charger into a standard 120 volt wall outlet. Note: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”. • Before first time use, charge the battery for at least 18 hours. Never charge the batteries longer than 30 hours. • Recharge the bat
Résumé du contenu de la page N° 10
Assembly F 2 Driver WARNING (Ring Side Down) Children can be harmed by small parts, Groove sharp edges and sharp points in the vehicle’s unassembled state, or by electrical Rib items. Care should be taken in unpacking and assembly of the vehicle. Children should Wheel not handle parts, including the battery, or (Flat Side Down) help in assembly of the vehicle. Hubcap (Flat Side Down) 1 Rear Axle (with Cap Nut) Rear Axle • Slide a hubcap (flat side down), a wheel (flat side down) and a driver (
Résumé du contenu de la page N° 11
Assembly Rear Wheel .437 Cap Nut 6 (Indented Side First) 4 Vehicle Body Driver Hubcap (Pointed Side First) Rear Axle Motor Rear Wheel Assembly • Slide the rear wheel assembly through a motor and the back end of the vehicle body. .437" 5 Motor •Fit the other driver onto the end of the rear axle. Make sure the teeth in the driver fit into the motor gearbox. • Slide a wheel (indented side first) and hubcap (pointed side first) onto the end of the rear axle. Make sure the ribs on the wheel fit int
Résumé du contenu de la page N° 12
Assembly .437 Cap Nut 8 10 Front Axle Short End Vehicle Body of Front Axle Washers Short End of Front Axle .437" • Fit a .437 cap nut onto the end of each front axle. • Slide a washer onto the short end of each front axle. • Fit the front axles up through the holes in the underside of the vehicle body. 11 9 Long Bushings Assembly Tool .437 Cap Nut Long Bushing • Fit the assembly tool onto the cap nut. • While supporting the front axle/steering linkage assembly, tap the assembly tool with a hamm
Résumé du contenu de la page N° 13
Assembly 12 14 Seat Wheel (Indented Side First) Hubcap (Pointed Side First) .437 Cap Nut Washer Bushing Front Axle (Ring Side First) Bushing Ring .437" Side •Insert a #10 x 1" screw through the back of the seat and into the vehicle body. Tighten the screw. •Turn the vehicle assembly upside down on a flat surface. •Fit a washer, bushing (ring side first), wheel (indented side first) and hubcap (pointed side first) 15 onto one of the front axles. Roll Bar • Fit a .437 cap nut onto the end of the
Résumé du contenu de la page N° 14
Assembly 16 18 .437 Cap Nut Dashboard End of Steering Column .437" • Fit a .437 cap nut on the end of the steering column. •Tap the cap nut with a hammer to secure the cap nut on the steering column. Pull on the cap nut to be sure it is secure. • Place the dashboard on the top side of the vehicle body, Hint: as shown. - You may need the help of another adult to keep these •Insert five #10 x 1" screws through the dashboard and two parts in the correct position. into the vehicle body. Tighten the
Résumé du contenu de la page N° 15
Assembly Windshield 22 20 Large Large Steering Column Tab Tab Large Hole in Dashboard Dashboard Bend Up Slot Slot Large Opening “UP” •Position the windshield so that the wipers face the front end of the vehicle. •Insert and "snap" the two large tabs on the windshield into the large slots in the dashboard. • Pull up on the windshield to be sure it is secure. •Insert the steering column (with steering wheel) into the large hole in the dashboard. Make sure the large opening in the steering wheel a
Résumé du contenu de la page N° 16
Assembly 24 26 Dashboard Slots Hood Tabs Brush Guard •Insert the tabs on the rear edge of the hood into the slots •Fit the brush guard on the front end of the vehicle. in the front of the dashboard. •Insert two #10 x 1" screws through the lower holes in the brush guard and into the front end of the vehicle. Tighten the screws. 25 Spacers 27 Lock Fastener Lock Fastener Unlocked Locked Brush Guard • Using a slotted screwdriver, turn each lock fastener in 1 the hood /4 turn to the locked position.
Résumé du contenu de la page N° 17
Label Decoration G Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind: •Wash your hands before applying the labels. • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. •For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a label, rub the label f
Résumé du contenu de la page N° 18
Label Decoration 11 11 2 3 2 12 13 8 12 10 13 9 Left Side 3 1 12 9 13 12 10 13 Right Side 18
Résumé du contenu de la page N° 19
Battery Installation H ® IMPORTANT! Use only a Power Wheels 6 volt battery Motor with A-style connector and built-in thermal fuse. Use of Harness 3 any other battery will damage your vehicle. Make sure that Connector you charge the battery for at least 18 hours using the ® ™ enclosed Power Wheels Super 6 volt charger before Battery operating your vehicle for the first time. Charge the Connector battery for at least 14 hours after each use of the vehicle. Never charge the battery longer than 30 h
Résumé du contenu de la page N° 20
Battery Care Battery Care and Disposal I and Disposal Care Disposal ® If a battery leak develops, avoid contact with the leaking •Your Power Wheels battery is sealed lead-acid battery. acid and place the damaged battery in a plastic bag. See They must be recycled or disposed of in an environ- information below for proper disposal. mentally sound manner. If acid comes in contact with skin or eyes, flush with • Do not dispose of a lead-acid battery in a fire. The cool water for at least 15 minut
