Résumé du contenu de la page N° 1
Product features and decorations may vary from photo above.
Instructions
Model Number: H7182
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE.
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires three “AA” (LR6) alkaline batteries for toy operation (not included).
www.fisher-price.com
1
Résumé du contenu de la page N° 2
Warning and Caution WARNING Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • Always keep child in view while in the high chair. • Never leave child unattended. • It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. CAUTION This product contains small parts in its unassembl
Résumé du contenu de la page N° 3
Parts Food Tray Electronic Toy Pad Toy Bar 2 Teether Toys Base Tray Seat Back #10 x 2.2 cm Black Screw Hinge Rod Frame Frame Seat Bottom 2 Seat Bottom Tubes #8 x 1.9 cm Screws - 4 2 Screw Retainers #8 x 1.9 cm Screws - 2 #8 x 1.9 cm Screws - 2 Back Base #10 x 2.2 cm #10 x 2.2 cm Black Screws - 2 Black Screws - 2 Footrest Screw Retainer Screw Retainer Note: Tighten and loosen all screws with a Phillips Front Base screwdriver. Do not over-tighten the screws. #10 x 2.2 cm Black Screws - 2 #10 x 2.
Résumé du contenu de la page N° 4
Assembly IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use Plastic Rings if any parts are missing or broken. Contact Mattel for replace- ment parts and instructions if needed. Never substitute parts. Seat Bottom Tubes Toy Bar 3 Plastic Rings • Slide a seat bottom tube through each set of plastic rings on the seat bottom. Electronic Toy 1 Plastic Rings •Insert and “snap” the toy bar into the electronic toy, as shown. f Se
Résumé du contenu de la page N° 5
Assembly Footrest Insert Screws Here Hinge Hinge Rod 5 7 #10 x 2.2 cm Black Screw - 2 #10 x 2.2 cm Black Screw • Insert two #10 x 2.2 cm black screws through the footrest and • Turn the seat assembly face down. into the seat bottom. Tighten the screws. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2.2 cm black screw into the hinge rod. Tighten the screw. Seat Back Pin Seat Back Pin • Set the seat assembly aside for Assembly step 9. Frame Le
Résumé du contenu de la page N° 6
Assembly Seat Height Adjusters Frame Decorated Side Position 4 Frame Back Legs Press Lever Back Base Hole 10 • While pressing the levers on the seat height adjusters, lift them Screw Retainers to position 4 on the frame front legs, as shown. Seat Assembly Back Base Hole Screw Retainer - 2 #10 x 2.2 cm Black Screw - 2 9 Sockets • Position a frame so that the decorated side is outward. • Insert the back leg of a frame into the back base. • Fit a screw retainer over the hole in the back base, as sh
Résumé du contenu de la page N° 7
Assembly #10 x 2.2 cm Black Screw - 2 Screw Retainer - 2 Push Seat Push Seat Height Height Adjuster Adjuster Front Leg Holes Screw Retainers Seat Bottom Tube Ends 12 13 #8 x 1.9 cm Screw - 2 • Insert the frame front legs onto the front base. • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Fit a screw retainer over a hole in the front leg. 7 • Insert a #8 x 1.9 cm screw through each seat height adjuster • Insert a #10 x /8" (2.2 cm) black screw thro
Résumé du contenu de la page N° 8
Assembly Pad Seat Height Adjusters #8 x 1.9 cm Screw - 2 Elastic Loops Hole Hole Front View Seat Bottom Tube Ends Back and Bottom View 14 Tabs • From the back and bottom of the assembly, insert a #8 x 1.9 cm screw through both seat height adjusters and the ends of the seat bottom tube. Tighten the screws. Elastic Loops 15 Back and Bottom View • Lift the assembly upright. • From the front of the assembly, place the pad onto the seat. • Lift the bottom of the pad. Insert the two elastic loops on t
Résumé du contenu de la page N° 9
Assembly Upper Shoulder Belt Slots Shoulder Portion Lower Shoulder Belt Slots Slot 18 Shoulder Portion Crotch Belt • Fit the top of the pad over the seat back. 16 • Fold the bottom edge of the pad under the edge of the seat bottom to fasten it. • Insert the crotch belt through the slot in the pad. Make sure • Insert the shoulder portion of the shoulder/waist belt through the crotch belt is not twisted. the slots in the pad and seat back. Use the lower shoulder belt • Fold the top of the p
Résumé du contenu de la page N° 10
Battery Installation Batteries may leak fluids that can cause a chemical burn injury or ruin our product. To avoid battery leakage: 1.5V x 3 • Do not mix old and new batteries or batteries of different "AA" (LR6) types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). Shown Actual Size • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of bat- teries safel
Résumé du contenu de la page N° 11
B A A Securing Your Child IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replace- ment parts and instructions if needed. Never substitute parts. Anchored End Place the high chair on a level, stable surface away from electri- Buckle cal flexes. Be sure to keep electrical flexes out of child’s reach. B WARNING Free End Prevent serious injury or death from falls or
Résumé du contenu de la page N° 12
Securing Your Child Hold Adjuster Shoulder Portion Pull Strap Down Slide Adjuster Down 6 • From the front of the high chair, pull the shoulder portion of the waist/shoulder belts out and then fit them back through the desired shoulder belt slots in the headrest pad, seat pad and the seat back. Pull on the belts to be sure they are secure in the 4 Tighten Loosen seat back. • To tighten the shoulder belts: Hold the adjuster and pull the front shoulder strap down. • To loosen the shoulder belts: Sl
Résumé du contenu de la page N° 13
Using the Trays and Toys WARNING Base Tray Prevent serious injury or death from falls or sliding out. The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. Release Bar 8 Hint: The base tray can be adjusted for your child’s comfort two ways (see steps 8 and 9)! • While pushing the release bar on the front of the base tray, adjust the base tray forward or backward. Base Tray Squeeze Latch Armrest Base Tray 9 • Wh
Résumé du contenu de la page N° 14
Using the Trays and Toys Electronic Toy Button Base Tray Tab Release Bar 11 Groove • While pushing the release bar on the front of the base tray, pull the tray base towards you and remove. 14 Base Tray Food Tray • Insert the tab on the edge of the electronic toy into the groove in the front of the base tray. • Push the electronic toy down to secure in place. Hint: The electronic toy does not fit into the food tray. Base Tray • To remove the electronic toy, press the button on the front of the el
Résumé du contenu de la page N° 15
Adjusting the Seat Storage WARNING WARNING Prevent serious injury or death from Prevent serious injury or death from falls or sliding out. falls or sliding out. It is recommended • Always leave wheels locked. that the high chair be used in the upright position only by children capable of sitting • Never use near steps. upright unassisted. Press Tab Lift Tab Seat Height Adjuster 18 TO LOCK: Press the tab down until you hear a "snap". TO UNLOCK: Lift the tab up. 4 16 Press Lever Hint: Adjust the s
Résumé du contenu de la page N° 16
Storage Storage Electronic Toy Tab Base Tray Hole Peg 21 19 • Fit the electronic toy to the tab on the back of the high chair, • Fit the holes on the base tray latches onto the pegs on the back as shown. of the high chair frame. Care • This prodduct may be wiped clean using a mild cleaning solu- Pull Frame tion and a damp cloth. Do not immerse the base tray. Release Latch • The food trays and toys are dishwasher safe. Simply remove the food tray from the base tray and place in your dishwasher
