Résumé du contenu de la page N° 1
INSTRUCTION MANUAL
CHAIN SAW
CS-530
WARNING
Read the instructions carefully and follow the rules for safe
operation.
Failure to do so could result in serious injury.
ECHO, INCORPORATED
X750-011 30 1
400 Oakwood Road, Lake Zurich, Illinois 60047-1564
X750 319-710 1
Phone : 847-540-8400
Printed in Japan 0804E 0365 ES
Résumé du contenu de la page N° 2
WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Copyright © 2007 All Rights Reserved.
Résumé du contenu de la page N° 3
RULES FOR SAFE OPERATION A. Kickback Safety Precautions for Chain Saw Users WARNING! KICKBACK may occur when the nose or 1.With a basic understanding of tip of the guide bar touches an object, or kickback, you can reduce or eliminate when the wood closes in and pinches the the element of surprise. saw chain in the cut. Sudden surprise contributes to accidents. Tip contact in some cases may cause a 2.Keep a good firm grip on the saw with lightning fast reverse REACTION, Kicking the guide bar
Résumé du contenu de la page N° 4
B. Other Safety Precautions 1.Do not operate a chain saw with one 11.Shut off the engine before setting the hand! Serious injury to the operator, chain saw down. helpers, bystanders, or any 12.Use extreme caution when cutting combination of these persons may small size brush and saplings because result from one-handed operation. slender material may catch the saw A chain saw is intended for two- chain and be whipped toward you or handed use. pull you off balance. 2.Do not operate a chain saw
Résumé du contenu de la page N° 5
CONTENTS RULES FOR SAFE OPERATION ............................................................................. 1 SYMBOLS AND SIGNS ........................................................................................... 3 PACKING LIST ......................................................................................................... 5 NOMENCLATURE OF PARTS ................................................................................. 6 OPERATOR SAFETY................................
Résumé du contenu de la page N° 6
SYMBOL FORM Symbol form/shape Symbol description/application Symbol form/shape Symbol description/application Carefully read the instruction Chain oil fill manual Wear eyes, ears and head Chain oil pump protection Chain brake operation Chain oiler adjustment Emergency stop Carburetor adjustment - Low speed mixture STOP Choke control “Cold Start” Carburetor adjustment position (choke closed) - High speed mixture Oil and gasoline mixture Carburetor adjustment - Idle speed DECALS Part Number X503-0
Résumé du contenu de la page N° 7
PACKING LIST The ECHO product you purchased has been After opening the carton, check for damage. factory pre-assembled for your convenience. Due to Immediately notify your retailer or ECHO dealer of packaging restrictions, guide bar and saw chain damaged or missing parts. Use the packing list to installation and other assembly may be necessary. check for missing parts. ECHO chain saw 13 x 19 mm T-wrench, 4 mm Hexagonal Wrench, Small screwdriver Spiked bumper, Instruction manual Safety manual × ×
Résumé du contenu de la page N° 8
NOMENCLATURE OF PARTS 4 3 5 6 7 1 8 14 9 10 11 12 13 2 890191-30131 X524-002000 Part Number 890191-30131 TO AVOID KICKBACK 1. Hold the chain saw firmly with X503-009050 both hands. 2. Don’t let the nose of the guide bar contact any obstruction. 3. Tip contact may suddenly move the guide bar upward and backward, 23 which may cause serious injury. 22 15 Part Number X524-002000 21 REPLACEMENT BAR AND CHAIN 16 GUIDE BAR* CHAIN* PART NO. TYPE LINKS 17 16” 16F0MD3366 OREGON 95VP 66 18” 18F0MD33
Résumé du contenu de la page N° 9
NOMENCLATURE OF PARTS 1. Instruction manual - Included with unit. 11. Spiked bumper - Device, fitted in front of the Read before operation and keep for future guide bar mounting point, acting as a pivot reference to learn proper, safe operating when in contact with a tree or log. techniques. 12. Guide bar - The part that supports and guides 2. Safety manual - Describe operating and safety the saw chain. instructions for this chain saw. 13. Saw chain - Chain, serving as a cutting tool. 3. Front h
Résumé du contenu de la page N° 10
OPERATOR SAFETY VIBRATION AND COLD EYE AND HEARING PROTECTION � It is believed that a condition called Raynaud’s � Wear eye protection goggles that meet ANSI Phenomenon, which affects the fingers of certain Z 87.1 requirements. individuals, may be brought about by exposure to Goggles meeting the requirements have the vibration and cold. mark “Z 87” stamped on them. Exposure to vibration and cold may cause � Wear hearing protection. tingling and burning followed by loss of color and If this guide
Résumé du contenu de la page N° 11
Kickback SPARK ARRESTOR MUFFLER � The spark arrestor muffler controls the exhaust This requirement also applies to all U.S. Forest noise and prevents hot, glowing particles of Service lands. carbon from leaving the muffler. In some of these areas, the spark arrestor system Make sure the spark arrestor screen is in good must be certified per USDA Forest Service repair and properly seated in the muffler. Regulation SAE J335. � Certain internal combustion engines operated on Check with your local o
Résumé du contenu de la page N° 12
PREPARATION FOR USE WARNING Saw chain is sharp! Always wear gloves when handling assembly, otherwise serious personal injury may result. ® KICK GUARD TO BAR INSTRUCTIONS Tools Needed: Two 11 mm (7/16 in.) Wrenches. Bolt (A) ® For saws with Kick Guard P/N 2893201 and Dimple (D) Symmetrical Low-Kick type (Double Guard) guide bars. ® 1. Install bolt (A) in rear hole (B) of Kick Guard ® Kick Guard and through front hole (C) in guide bar. Rear hole (B) ® 2. IMPORTANT: Dimple (D) in Kick Guard must
Résumé du contenu de la page N° 13
5. Mount guide bar on studs and slide toward clutch Guide bar studs Clutch to make saw chain installation easier. Install chain with cutters on top of guide bar facing forward. Guide bar adjuster hole 6. Unlock the chain brake, and install the clutch Hole cover over the guide bar studs. Ensure chain Nuts Pin tension adjuster pin fits into the guide bar Adjuster pin adjuster hole, brake band is positioned around clutch drum, and pin at rear of clutch cover fits Clutch cover hole on engine cover.
Résumé du contenu de la page N° 14
FUEL AND LUBRICANT FUEL STATEMENT GASOLINE - Use 89 Octane [(R+M)/2] (mid grade WARNING or higher) gasoline or gasohol known to be good Alternative fuels, such as E-20 (20 % quality. ethanol), E-85 (85 % ethanol) or any fuels not Gasohol may contain up to 10 % Ethyl (grain) meeting above requirements are NOT alcohol or 15 % MTBE (methyl teriary-butyl ether). approved for use in ECHO 2-stroke gasoline Gasohol containing methyl (wood) alcohol is NOT engines. approved. Use of alternative fuels m
Résumé du contenu de la page N° 15
HANDLING FUEL MIXING INSTRUCTIONS - DANGER 1. Fill an approved fuel container with half of the Fuel is VERY flammable. Use extreme care required amount of gasoline. when mixing, storing or handling or serious 2. Add the proper amount of two-stroke oil to personal injury may result. gasoline. � Use an approved fuel container. � DO NOT smoke near fuel. 3. Close container and shake to mix oil with � DO NOT allow flames or sparks near fuel. gasoline. � Fuel tanks/cans may be under pressure. 4. Ad
Résumé du contenu de la page N° 16
CHAIN LUBRICANT Proper lubrication of the chain while in operation Cap indication reduces friction between the chain and the guide Fuel/oil tanks are indicated by the following bar to a minimum and assures a longer service life. illustrations. � Use bar and chain oil of high quality for this purpose. � Do not use used or reclaimed oil to avoid various oiler problems. � Use ECHO bar and chain oil. � When ECHO bar and chain oil is not available: Use motor oil, etc. � Use bar and chain oil of the f
Résumé du contenu de la page N° 17
WHEN THE ENGINE IS COLD Chain brake CAUTION Make sure the bar and chain are free from any obstruction when starting the chain saw. � Move chain brake lever fully forward to lock chain brake before starting. Ignition switch � Fill the fuel tank with fuel mixture. It is not permitted to fill fuel above the shoulder Start / Run level of fuel tank. � Fill the chain oil tank with lubricant. Do not over fill. � Move ignition switch to “RUN” position. Throttle trigger lockout � Pull choke control kn
Résumé du contenu de la page N° 18
RUNNING � When engine starts, keep idling for a few Unlock chain brake minutes. � Set the brake lever in the unlocked position before starting to cut. � Pull throttle trigger gradually and increase revolution of the engine. � The chain starts running when the engine reaches 3800 r/min approximately. � Confirm proper acceleration and lubrication of chain and bar. � Do not run the engine at high speed unnecessarily. � Be sure that saw chain stops moving when throttle trigger is released. STOPPING
Résumé du contenu de la page N° 19
CUTTING INSTRUCTION GENERAL CAUTION � Read the ECHO “CHAIN SAW SAFETY MANUAL” included with your chain saw for additional cutting and safety instructions. � Wear suitable hearing protection such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. � Do not let the tip of the bar touch anything while the engine is running. At cutting speed the chain is moving at a high rate of speed. Should the tip contact a limb or log while the chain is moving, the tip will
Résumé du contenu de la page N° 20
FELLING THE TREE A falling tree can seriously damage anything it may hit - a car, a house, a fence, a power-line, or 3 m (10 feet) another tree. There are ways to make a tree fall where you want Retreat Direction of fall it, so first decide where that is! 45° Before cutting, clear the area around the tree. You will need good footing while working and you 45° should be able to work the saw without hitting any obstacles. Next, select a path of retreat. Retreat Not this way When the tree begins to
