Résumé du contenu de la page N° 1
Operator’s and Safety Manual
for Gasoline Chain Saws (page 2 - 38)
Manuel d’emploi et de sécurité
de tronçonneuses thermiques (page 39 - 75)
WARNING!
Read and understand this Manual. Always follow safety precautions in the Operator’s and Safety Manual. Improper use can cause serious injury! Preserve this Manual carefully!
WARNING!
FUELS WITH MORE THAN 10% ETHANOL ARE NOT APPROVED FOR USE IN DOLMAR 2-STROKE ENGINES!
Use of alternative fuels, such as E-20 (20% ethanol), E-85 (85% ethanol) or any
Résumé du contenu de la page N° 2
EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The U.S. Environmental Protection Agency (EPA), the California Air Resources Board and DOLMAR are pleased to explain the emissions control system’s warranty on your 2011 model year small off-road (equipment type) engines. In California, new equipment that use small off-road engines must be designed, built, and equipped to meet the State’s stringent anti-smog standards. DOLMAR must warrant the emissions control system on
Résumé du contenu de la page N° 3
(5) Notwithstanding the provisions of Subsection (4) above, warranty services or repairs must be provided at all manufacturer distribution centers that are franchised to service the subject engines. (6) The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station. (7) The manufacturer is liable for damages to other engine components proximately caused by a
Résumé du contenu de la page N° 4
WARNING ! Careless or improper use of this product can cause serious or even fatal injury. Before operating a chain saw or other DOLMAR products it is important that you read, fully understand and carefully follow the instructions outlined in this operator’s manual. Kickback may cause severe or fatal injury and is one of many potential dangers in operating a chain saw. Kickback and other safety related precautions are described in detail within this operator’s manual. Additional operator’s m
Résumé du contenu de la page N° 5
Delivery inventory 2 3 4 1 Chain saw 2 Guide bar 1 8 5 6 7 3 Saw chain 4 Chain protection cover 5 Universal wrench 6 Wrench 7 Screw driver for carburetor adjustment 8 Cylinder fin cleaner In case one of the parts listed should not be included in the 9 Operator’s and Safety Manual (not shown) delivery inventory, please consult your sales agent. Symbols You will notice the following symbols on the chain saw and in the Operator’s and Safety Manual: Read Operator’s and Safety Manual and follow th
Résumé du contenu de la page N° 6
Safety precautions for chain saw operators Additional safety precautions While operating the chain saw please observe the The following additional safety precautions must be following rules: observed by all users of chain saws: a) Contact of the guide bar nose with any object 1. Do not operate a chain saw when you are fati- should be avoided. gued. b) Tip contact may cause the guide bar to move 2. Use safety footwear; snug-fitting clothing; protec- suddenly upward and backward, which
Résumé du contenu de la page N° 7
O max. CKA 45 Maximum Computed Kickback Angle General Safety Precautions (CKA)* without using the chain brake when using the recommended bar and chain The use of any chain saw may be hazardous. At full combinations (In this example the CKA is 45°). throttle chain speed can reach 45 mph (20 m/s). It is important that you read; fully understand and observe O max. CKA 40 MaximumComputed Kickback Angle the following safety precautions and warnings. Read (CKA)* with using the chain brake w
Résumé du contenu de la page N° 8
Proper clothing The saw Parts of the chain saw: illustrations and description of Clothing must be sturdy and snug-fitting, but allow parts see page 18. complete freedom of movement. Avoid loose-fitting jackets, scarfs, neckties, jewelry, flared or cuffed pants, or anything that could become entangled with the saw WARNING ! or brush. Wear overalls or jeans with a reinforced cutting resistant insert (fig. 3). Never modify a chain saw in any way. Only at- tachments supplied by DOLMAR or expre
Résumé du contenu de la page N° 9
Wipe off any spilled fuel before starting your saw and Chain saw operating instructions check for leakage. For assembly follow the procedure in the appropriate Check for fuel leakage while refueling and during opera- section "Mounting Guide Bar and Chain" of this manual. tion. If fuel or oil leakage is found, do not start or run DOLMAR chain, guide bar and sprocket must match each the engine until leak is fixed and spilled fuel has been other (see the appropriate section in this manual). w
Résumé du contenu de la page N° 10
Wrap your fingers tightly around the handles, keeping Important adjustments the handles cradled between your thumb and forefin- ger (fig. 7). With your hands in this position, you can WARNING! best oppose and absorb the push, pull and kickback At correct idle speed, chain should not turn. For di- forces of your saw without having it slip out of your rections to adjust idle speed, see the appropriate grip (see section of reactive forces). Make sure your section of this operator’s manual. ch
Résumé du contenu de la page N° 11
9 In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support. Never use the saw above shoulder height (fig. 9). 10 11 Position the chain saw in such a way that your body is Kickback: clear of the cutting attachment whenever the engine Kickback occurs when the upper quadrant of the bar is running (fig. 10). nose contacts a solid object in the wood or is pinched (fig. 11). The reaction of the cutting force of th
Résumé du contenu de la page N° 12
Many factors influence the occurence and force of the kickback reaction. The type of bar and saw chain you use is a factor in the force of the kickback reaction. The speed of contact at which the cutter contacts the object. Kickback force increase with the rate of impact. The contact angle between the nose of the bar and the foreign object (fig. 11). Kickback is most pronounced in the upper quadrant 13 of the bar nose. To avoid kickback DOLMAR chain types are designed to reduce kickback
Résumé du contenu de la page N° 13
Pushback: To avoid pull-in Pushback occurs when the chain on the top of the 1. Always start a cut with the chain rotating at full speed bar is suddenly stopped when it is pinched, caught and the spike bar in contact with the wood. or encounters a foreign object in the wood. The reac- tion of the chain drives the saw straight back toward 2. Pull-in may also be prevented by using plastic the operator causing loss of saw control. Pushback wedges to open the kerf or cut. fre-quently occurs when
Résumé du contenu de la page N° 14
45° 1 2 2 First cut 45° Second cut = cutting down area 20 17 When felling, maintain a distance of at least 2 1/2 tree If the tree has large buttress roots, cut into the largest lengths from the nearest person (see fig. 17). buttresses vertically first (horizontally next) and remove (fig. 20). Note: The noise of your engine may drown any warning call. Felling instructions: Direction of fall 21 18 First clear the tree base and work area from inter- Felling cut fering limbs and brush and clean it
Résumé du contenu de la page N° 15
Begin the felling cut slighty higher than the felling notch Plunge-Cut Method and on the opposite side of the tree (fig. 22). Then cut Timber having a diameter more than twice the length horizontally through towards the felling notch. Apply of the guide bar reauires the use of the plunge-cut the chain saw with its spikes directly behind the uncut method before making the felling cut. portion of wood and cut toward the notch (fig. 23). First, cut a large, wide notch. Make a plunge cut in t
Résumé du contenu de la page N° 16
Bucking 3 Bucking is cutting a log into sections. 2 1 29 WARNING! 31 There is an extreme danger of kickback at this point. Extra caution must be taken to maintain control of the saw. To make the felling cut, follow WARNING! the sectioning method described previously (fig. 1. When bucking, do not stand on the log. Make 29). If you are inexperienced with a chain saw sure the log will not roll down-hill. If on a slope, plunge-cutting should not be attempted. Seek the stand on the up-hill
Résumé du contenu de la page N° 17
Maintenance and Repair Never operate a chain saw that is damaged, improperly adjusted or not completely or securely assembled. Follow the maintenance and repair instructions in the appropriate section of this manual. WARNING ! Always stop the engine and make sure that the chain is stopped before commencing any maintenance 33 or repair work or cleaning the saw. Allow the chain saw to cool off before doing any maintenance work (burn hazard)! Chain saws with catalytic converter take longer
Résumé du contenu de la page N° 18
Denomination of components 1 2 3 4 5 4a 6 7 8 9 10 26 11 12 27 13 14 15 16 17 25 18 19 Identification plate Serial no. 24 23 24" (600mm) 2011.11 123456 Year of manufacture 415.060.655 528.099.084 DOLMAR GmbH, 22045 Hamburg, Germany 038.100.250 Typ 038 22 21 20 Indicate when ordering spare parts! 1 Handle 15 Adjusting screws "S-L-H" for carburetor 2 Filter cover 16 I/STOP-switch 3 Filter hood clip 17 Choke lever 4 Tubular handle (4a model with wrap around handle) 18 Throttl
Résumé du contenu de la page N° 19
Technical data PS-6400 PS-7300 PS-7900 3 Stroke volume cu. in (cm ) 3.9 (64) 4.4 (72.6) 4.8 (78.5) Bore inch (mm) 1.85 (47) 1.97 (50) 2.04 (52) Stroke inch (mm) 1.45 (37) 1.45 (37) 1.45 (37) 1) Max. power at speed hp / rpm 4.7 / 9,000 5.6 / 9,500 6.2 / 9,500 1) Max. torque at speed Nm / rpm 4.2 / 6,500 4.8 / 7,000 5.2 / 7,000 Limit speed with guide bar and chain rpm 13,500 13,500 13,500 Idling speed rpm 2,500 2,500 2,500 Coupling speed rpm 3,200 3,200 3,200 Sound Pressure Le
Résumé du contenu de la page N° 20
PUTTING INTO OPERATION CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Always wear protec- tive gloves! CAUTION: Start the chain saw only after having assembled it com- pletely and inspected. A Mounting the guide bar and saw chain Use the universal wrench delivered with the chain saw for the following work. Put the chain saw on a stable surface and carry out the following 1 ste
