Résumé du contenu de la page N° 1
UNVENTED (VENT-FREE) GAS LOG HEAT ER
OWNER’S OP ER A TION AND IN STAL LATION MANU AL
For more information, visit www.desatech.com
VF-24N-PDG, VF-24P-PDG, VF-24N-BTB, VF-24P-BTB,
VF-18N-PDG, VF-18P-PDG VF-18N-BTB, VF-18P-BTB
Design Dynamics Vent-free Mod els Also De sign-Certi fi ed As Vented Dec o rativ e Appli anc es
WARNING: Improper in stal la tion, ad just -
WARNING: If the information in this man u al
ment, al tera tion, service, or main te nance
is not followed exactly, a fi re or explo
Résumé du contenu de la page N° 2
TABLE OF CONTENTS 2 SAFETY INFORMATION TABLE OF CONTENTS SAFETY INFORMATION ..............................................................2 CLEANING AND MAINTENANCE .............................................18 PRODUCT IDENTIFICATION .......................................................3 TROUBLESHOOTING ................................................................19 OPTIONAL REMOTE CONTROL ACCESSORIES ......................4 SPECIFICATIONS .................................................
Résumé du contenu de la page N° 3
SAFETY INFORMATION 3 PRODUCT IDENTIFICATION 3 SAFETY INFORMATION Continued 14. Turn heater off and let cool before ser vic ing, installing, or 1. This appliance is only for use with the type of gas indicated on re pair ing. Make sure the selector switch is in the OFF position the rating plate. This appliance is not convertible for use with (Remote-Ready Models Only). Only a qual i fi ed ser vice per son other gases. should install, ser vice, or repair heater. 2. Do not place propane/LP supp
Résumé du contenu de la page N° 4
OPTIONAL REMOTE CONTROL ACCESSORIES 4 LOCAL CODES UNPACKING PRODUCT FEATURES AIR FOR COMBUSTION AND VENTILATION Providing Adequate Ventilation OPTIONAL REMOTE CONTROL ACCESSORIES SAFETY DEVICE There are four optional remote controls that can be purchased This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff sys tem. The ODS/pilot is a re quired fea ture for vent- separately for Remote-Ready Models Only: free room heat ers. The ODS/pilot shuts off the heater if there i
Résumé du contenu de la page N° 5
AIR FOR COMBUSTION AND VENTILATION 5 Providing Adequate Ventilation (Cont.) 5 Determining Fresh-Air Flow for Heater Location If additional ventilation to adjoining room is supplied with grills or open- AIR FOR COMBUSTION AND ings, add the volume of these rooms to the total vol ume of the space. VENTILATION 2. Multiply the space volume by 20 to determine the maximum Btu/Hr Continued the space can support. Unusually tight construction is de fi ned as construction ____________(volume of spac
Résumé du contenu de la page N° 6
AIR FOR COMBUSTION AND VENTILATION Ventilation Air 6 AIR FOR COMBUSTION AND VENTILATION Continued VENTILATION AIR 12" Ventilation Air From Inside Building This fresh air would come from an adjoining unconfi ned space. When ventilating to an adjoining unconfi ned space, you must pro vide two Ventilation permanent open ings: one within 12" of the ceiling and one within Ventilation Grills Grills 12" of the fl oor on the wall con nect ing the two spaces (see options Into Adjoining Room, Into
Résumé du contenu de la page N° 7
INSTALLATION 7 Check Gas Type 7 Installation and Clearances for Vent-Free Operation INSTALLATION NOTICE: This heater is in tend ed for use as sup ple - CAUTION: This heater cre ates warm air currents. men tal heat. Use this heater along with your pri ma ry These currents move heat to wall sur fac es next to heat ing system. Do not in stall this heat er as your pri- heater. Installing heater next to vinyl or cloth wall cov- ma ry heat source. If you have a central heating system, er ing
Résumé du contenu de la page N° 8
INSTALLATION Installation and Clearances for Vent-Free Operation (Cont.) 8 INSTALLATION Continued Carefully follow the instructions below. This will ensure safe in- noncom b us ti ble ma te ri al behind it. Noncomb ustible ma te ri al must stal la tion into a masonry, UL127-listed manufactured fi replace, or extend at least 8" up (for all mod els). If noncombustible ma te ri al list ed vent-free fi re box. is less than 12", you must install the fi re place hood accessory (24" and 30" Models On
Résumé du contenu de la page N° 9
INSTALLATION 9 Mantel Clearances 9 Floor Clearances INSTALLATION Continued Mantel Shelf 10" Underside of 8" Mantel Shelf MANTEL CLEARANCES 6" 1 2 /2" In addition to meeting noncom bus ti ble ma te ri al clearances, you must also meet required clearances between fi replace open ing and mantel shelf. If All minimum you do not meet the clear anc es listed below, you will need a hood. distances are in inches Minimum Non- Determining Minimum Mantel Clearance (A) Combustible Log Set Material 12"
Résumé du contenu de la page N° 10
INSTALLATION Installing Damper Clamp Accessory for Vented Operation 10 Installing Heater Assembly INSTALLATION Continued INSTALLING DAMPER CLAMP ACCESSORY INSTALLING HEATER ASSEMBLY FOR VENTED OPERATION WARNING: If installing in a sunken fi re place, special care is needed. You must raise the fi re place Note: When used as a vented decorative, ap pli ance must be installed only in a solid-fuel burning fi replace with a working fl ue and con- fl oor to allow access to heat er control panel. This
Résumé du contenu de la page N° 11
INSTALLATION 11 Installing Heater Assembly (Cont.) 11 Connecting to Gas Supply INSTALLATION Continued CONNECTING TO GAS SUPPLY Installation must include an equipment shutoff valve, union, and WARNING: This appliance requires a 3/8" NPT plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge (National Pipe Thread) inlet connection to the pres- hook up. NPT tap must be up stream from heater (see Figure 13 sure regulator. page 12, depending on your model). IMPORTANT: Install equipme
Résumé du contenu de la page N° 12
INSTALLATION Connecting To Gas Supply (Cont.) 12 Checking Gas Connections CHECKING GAS CONNECTIONS INSTALLATION Continued 2. Cap off open end of gas pipe where equip ment shutoff valve was con nect ed. CSA Design-Certifi ed Equipment PROPANE/LP 3. Pressurize supply pip ing sys tem by ei ther opening pro pane/LP Shutoff Valve With 1/8" NPT Tap* - From External sup ply tank valve for propane/LP gas or opening main gas valve Approved Flexible Regulator lo cat ed on or near gas meter for natur
Résumé du contenu de la page N° 13
INSTALLATION 13 Checking Gas Connections (Cont.) 13 INSTALLATION Continued Equipment Shutoff Valve Propane/LP Thermostat Gas Supply Tank Valve or Control Valve Location Figure 15 - Checking Gas Joints (propane/LP only) Thermostat Gas Thermostat Gas Valve or Control Valve or Control Valve Location Valve Location Gas Meter Figure 16 - Checking Gas Joints (Natural Gas Only) For more information, visit www.desatech.com 111826-01F
Résumé du contenu de la page N° 14
O N O T 14 OPERATING HEATER (REMOTE-READY MODELS) For Your Safety Read Before Lighting Lighting Instructions OPERATING HEATER NOTICE: During initial operation of new heat er, me- REMOTE-READY MODELS tallic components may emit an odor as paint and assembly compounds are heated and cure. Be sure FOR YOUR SAFETY READ to provide adequate fresh air if odors are detected. BEFORE LIGHTING Note: Home owners generally prefer to op er ate their heater with the chimney damper closed. This will put all
Résumé du contenu de la page N° 15
O REMOTE OFF ON N O T OPERATING HEATER (REMOTE-READY MODELS) 15 Lighting Instructions (Cont.) 15 To Turn Off Gas To Appliance Manual Lighting Procedure Remote Control Operation OPERATING HEATER Continued Ignitor 7. With control knob pressed in, press and release ignitor but- Pilot Ignitor Pilot Electrode ton. This will light pilot. The pilot is attached to the front Burner Electrode Burner burner. If needed, keep press ing ig ni tor button until pilot lights. Note: If pilot does not stay
Résumé du contenu de la page N° 16
O REMOTE OFF ON N O T OPERATING HEATER (REMOTE-READY MODELS) Remote Control Operation (Cont.) 16 3. To turn the burner off, press the AUTO/ON/OFF button OPERATING HEATER un til OFF lights. The pi lot will re main lit. Continued IMPORTANT: To turn the pilot off, man u al ly turn the con trol knob on the heat er to the OFF position. IMPORTANT: Do not leave the se lec tor switch in the RE- MO TE or ON position when the pilot is not lit. This will drain the battery. 2. Press the ON/OFF butt
Résumé du contenu de la page N° 17
INSPECTING BURNERS 17 Pilot Flame Pattern 17 Burner Flame Pattern INSPECTING BURNERS Check pilot fl ame pattern and burner fl ame patterns often. BURNER FLAME PATTERN Figure 24 shows correct burner fl ame pattern. PILOT FLAME PATTERN NOTICE: Do not mistake orange fl ames with yellow Figure 22 shows a correct pilot fl ame pat tern. Figure 23 shows an tipping. Dirt or other fi ne particles are burned by heat er, incorrect pilot fl ame pattern. The incorrect pilot fl ame is not touch ing causing brief
Résumé du contenu de la page N° 18
CLEANING AND MAINTENANCE Cleaning Burner Injector Holder and Pilot Air Inlet Hole 18 CLEANING AND MAINTENANCE if com pressed air is not available. LOGS WARNING: Turn off heater and let cool before cleaning. • If you remove logs for cleaning, re fer to Installing Logs, page 14, to prop er ly re place logs. CAUTION: You must keep control areas, burners, Ports and circu lat ing air pas sage ways of heat er clean. In- Slots Injector spect these areas of heater bef ore each use. Have
Résumé du contenu de la page N° 19
TROUBLESHOOTING 19 19 TROUBLESHOOTING Note: For additional help, visit WARNING: Turn off and un- CAUTION: Never use a wire, DESA technical service web site at plug heater and let cool bef ore needle, or similar object to clean www.desatech.com. servicing. Only a qualifi ed service ODS/pilot. This can damage ODS/ person should service and repair pilot unit. Note: All troubleshooting items are listed heater. in order of operation. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY When ignitor but
Résumé du contenu de la page N° 20
TROUBLESHOOTING 20 TROUBLESHOOTING Continued OBSERVED PROBLEM POSSIBLE CAUSE REMEDY One or both burner does not light after 1. Inlet gas pressure is too low 1. Contact local natural or pro pane/LP gas ODS/pilot is lit company 2. Burner orifi ce(s) clogged 2. Clean burner(s) (see Cleaning and Main te nance, page 18) or re place burner orifi ce(s) 3. Mislocated crossover tube 3. Contact qualifi ed service person 4. Burner orifi ce(s) di ame ter is too small 4. Replace burner orifi ce(s) 5. Remote s
