Résumé du contenu de la page N° 1
O W N E R ' S M A N U A L
L A W N S W E E P E R
SWEEPER MODEL:
SW-15CC
PATENT NO. US 6,640,532 B1
Assembly
Installation
Operation
Repair Parts
For use with Lawn/Garden Tractors
Important:This manual contains information for the safety of
persons and property. Read it carefully before assembly and
operation of the equipment!
L-1788-CC-B
Résumé du contenu de la page N° 2
CONGRATULATIONS on your the purchase pf your new Brinly-Hardy Lawn Sweeper! Your lawn sweeper is designed, engineered and manufactured to give you the best possible dependability and performance. CUSTOMER RESPONSIBILITIES Please read and retain this manual. The instructions enables you to assemble and maintain your lawn roller properly. And please, always observe the "Safety" instructions. TABLE OF CONTENTS SAFETY ............ .....................................................
Résumé du contenu de la page N° 3
TO HELP PREVENT BODILY INJURY DUE TO LOSS OF TOWING SAFELY STABILITY OR CONTROL. Stopping distance increases with speed and weight of towed load. Travel slowly and allow extra time and distance Do not exceed maximum towing capacity of towing vehicle to stop. listed in the vehicle operator's manual. Total towed weight must not exceed limits specified in Do not exceed 5 mph. towing vehicle operator's manual. Do not tow this machine behind a motor vehicle such as a car, truck or ATV. Excessive
Résumé du contenu de la page N° 4
PARTS REFERENCE Tools Required for Assembly: 1/2” Wrench (2) 9/16” Wrench (2) Pliers Safety Glasses Gloves 4. L-1788-CC-B 3 43 64 31 39 44 40 4 5 48 65 35 62 37 32 49 34 7 9 9 62 24 6 40 12 9 23 32 36 25 21 32 38 59 1 29 27 28 15 16 26 22 30 14 8 11 61 10 16 2 17 20 63 9 18 42 13 16 26 19
Résumé du contenu de la page N° 5
PARTS LIST QTY REF. NO. PART NO. DESCRIPTION 1 1 R-2251-10 Hitch Clevis Assembly 2 2 R-2254-10 Tow Tube 1 3 R-2270-10 Lift Handle 1 4 B-7063 Caution Label 1 5 B-7009 Logo Decal 6 6 11M0808P Carriage Bolt, ¼" x ½" 4 7 2M1012P Hex Bolt, 5/16" x ¾" 6 8 B-1673P Hex Lock Nut, ¼" 9 9 B-4786 Nylon Insert Lock Nut, 5/16" 1 10 R-2415-10 Lower Pivot Assembly 50 2 11 R-2288 Bearing Assembly 55 2 12 R-2289 Bearing Retainer 2 13 R-2293-1 Inner Dust Shield 1 14 R-2416 Lift Link 4 15 R-2321 Self-Taping Screw
Résumé du contenu de la page N° 6
Step 1. 14 31 62 9 5/16" Nylon Lock Nut Qty. 4 9 62 5/16" x 1-1/2", Carriage Bolt 35 Qty. 4 a) Attach Upper Frame Assembly(35) to Brush Housing Assembly(31). b) Assemble Lift Link(14) as shown. Step 2 3 39 5/16" Hex Nut Qty. 1 39 44 40 44 Lock Pin Qty. 1 40 5/16" Lock Washer Qty. 1 a) Preassemble the Lock Pin(44) to the Lift Handle(3). 6. L-1788-CC-B
Résumé du contenu de la page N° 7
3 Step 2a 9 5/16" Nylon Lock Nut Qty. 1 9 38 14 5/16" x 1-3/4", Hex Bolt 38 Qty. 1 32 36 32 5/16" Flat Washer 10 Spring 32 36 Qty. 2 Qty. 1 c) Complete the assembly by adding a) Assemble Lift Handle(3) to Lift Link(14). the spring, washer and locknut. b) Install hex bolts (38) as shown. Add washer (32) and install handle in middle hole. NOTE: It may be necessary to put downward pressure on the Lower Pivot assembly (10) to line up the holes. 3 Step 3 43 37 5/16" x 1-1/2",
Résumé du contenu de la page N° 8
Step 4. ATTACHING CLEVIS Attach the Hitch Clevis Assembly(1) to the Tow Tubes (2), as shown. a) Install Hex Bolts (63) through Tow Tubes (2) and Hitch Clevis Assembly (1), as shown b) Install Lock Nuts (9) to Hex 2 Bolts. Tighten loosely. 41 1 42 9 63 9 41 63 5/16" Nylon Lock Nut Hairpin Cotter, 1/8” 5/16" x 2-1/4", Hex Bolt Qty. 2 Qty. 1 Qty. 2 8. L-1788-CC-B
Résumé du contenu de la page N° 9
T O P E DGE OF PAG E PATENT NO. US 6,640,532 B1 Step 5. 11" Manual 10" Hitch Clevis Assembly 3 2 11" TOP EDGE OF PAGE 10" 9" 9" 8" 7" 6" 8" NOTE: Step 4 is for attaching the Hitch Clevis Assembly (1) to the TowTubes(2), When complete, the tow tubes(2) will be approximately level with the pavement: a) Using this page, set the manual on the floor and measure your hitch height as shown in illustration. 7" b) Position the Hitch Clevis Assembly between the tow tubes for the proper
Résumé du contenu de la page N° 10
53 Step 6. a) Install hex nuts to hamper stop rod(54). 52 b) Assemble rear tube(53) with holes up to lower tube(52). c) Install hamper stop rod(54) to lower tube(52). 52 46 46 3/8" Hex Nut Qty. 2 54 46 Step 7. a) Lower the assembly in Step 6 into the bottom of 54 hamper(55). 53 b) Assemble the rear tube(53) with the holes down as shown. c) Assemble the side tubes(56) into the rear tube (53) and into the hamper stop rod (54) 55 56 56 10. L-1788-CC-B
Résumé du contenu de la page N° 11
Step 8. 53 a) Locate and align the holes in the upper rear 56 tube (53) with the side tubes (56). Locate and align the holes in the lower rear tube (53) with 58 the bottom tube (52). 53 b) Stand in the bottom of the hopper. Insert the end of the spring rod (58) into the lower holes aligned in step a. Pull up on the upper rear tube (53) and insert the other end of the 56 spring rod (58) into the upper holes. 52 Please note that this step must be done with 54 eye protection (safety gla
Résumé du contenu de la page N° 12
Step 10. 57 62 56 62 Hairpin Cotter, .08 x 1-3/16" 61 Qty. 2 61 Clevis Pin, 5/16" x 2" a) The windscreen can be allowed to hang vertically in the back of the hamper or can be Qty. 2 attached as shown. Thread the elastic loops over the washer as shown, or the loops can be placed between the hamper mount tube (57) and the side tubes (56). b) Attach hamper assembly to back of sweeper. c) Hamper should not touch ground. For adjustment see section “Leveling Hamper” at end of this manual. OPERA
Résumé du contenu de la page N° 13
The following maximum loaded weight capacity is the average LEVELING HAMPER weight of the sweeper plus the weight loaded in the hamper. After the brush height has been set, the tow tubes may require adjustment to level the tow tubes to the ground. This can be accomplished by removing Model Weight Capacity the clevis and adjusting the clevis up or down, (refer to step 5) After the tow tubes are approximately level, the hamper stop assembly may have to
Résumé du contenu de la page N° 14
The hamper pull rope (50) can be routed to the tow vehicle operator’s area FREQUENTLY ASKED QUESTIONS and temporarily secured. The operator can then empty the hamper while seated in the operating position. Sweeper does not pick up: To empty hamper: 1. The adjustement lever is set too low. A sweeper is not a dethatcher and 1. Stop towing machine. cannot pull thatch, embedded needles or leaves from deep in the 2. Engage park brake. grass.The adjustment height should be set t
Résumé du contenu de la page N° 15
SERVICE Do not allow material to remain in the hamper for extended periods of SPECIFICATIONS time. Clean the hamper using a water hose and allow to dry prior to storage. Maximum Towing Speed ................................. 5 mph Check all moving parts for wear and freedom of movement. Hamper Capacity ............................................. 15 cu.ft. Routine lubrication of the pinion and dowel pin is required. We Maximum Hamper Weight .............................. 120 lbs. recommend
Résumé du contenu de la page N° 16
MANUFACTURER’S LIMITED WARRANTY FOR Pull Behind Accessories The limited warranty set forth below is given by Brinly-Hardy Co. with The provisions as set forth in this warranty provide the sole and respect to new merchandise purchased and used in the United exclusive remedy arising from the sale. Cub Cadet LLC shall States, its possessions and territories. not be liable for incidental or consequentia loss or damage including, without limitation, expenses incurred for substitite or Brinly-
