Résumé du contenu de la page N° 1
OWNERS
MANUAL
MODEL NO.
315.111450
CAUTION:
3/8 INCH
Read Rules for
CORDLESS DRILL
Safe Operation
and instructions
SINGLE-SPEED- REVERSIBLE
Carefully
Introduction
SAVE THIS
Operation
MANUAL FOR
FUTLIRE REFERENCE
Designed exc_usive}y for arid sold only by
SEARS, ROEBUCK AND CO, Dept 698/73tA, Sears Tower. Chicago. IL 60684
_QXj9
Résumé du contenu de la page N° 2
FULL ONE YEAR WARRANTY ON CRAFTSMAN CORDLESS DRILL If this Craftsman Cordless Drill falls to give complete satisfaction within one year from the date of put.- chase, RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears wilt replaceit, freeof charge. If this cordless drill isused for commercial or rentatpurposes this warranty applies for only 90 days from the dateof purchase. This warranty gives you specific lega! rights, andyou mayalso haveotherrights whichvaryfromstate to
Résumé du contenu de la page N° 3
RULES FOR SAFE OPERATION (CONTINUED) !4,. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see thdt keys and adjusting wrenches are removed from tool before turning it on, 15. NEVER USE IN AN EXPLOSIVE ATMOSPHERE_ Normat sparking of the motor could ignite flammable liquids, gases or fumes, t6 KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning.. Never use brake fluids, gasoline, petroleum_based products, or any strong solvents to clean your
Résumé du contenu de la page N° 4
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER 1. SAVE THESE INSTRUCTIONS° This manual contains important safety and operating instructions for battery charger Part Number 999555-007. 2. Before using battery charger, read atl instructions and cautionary markings in this manual, on battery charger, and product using battery charger. 3. __To reduce risk of injury, charge only nickel-cadmium type rechargeable batteries. Other types of batteries may burst causing personal injury and damage, 4o Do not e_,
Résumé du contenu de la page N° 5
OPERATION KNOW YOUR DRILL TO CHARGE See Figure 1_ 1, Connect charger to your drill by inserting charger plug Into input jack, NOTE: As shown In Before attempting to use your drill, familiarize Figure 1, input Jack is located at the rear of toot yourself with el! operating features and safety re- quirements, 2 Charger can be used with normal house voltage of 110.120 volts, 60 Hz. AC only. If any pads are missing do not operate your drill untie 3, Connect charger Io power supply the missing parts
Résumé du contenu de la page N° 6
OPERATION (Cont.) BATTERIES Your ddtl is equipped with 5 nickel-cadmium rechargeabte batteries Length of service from each charging will depend on the type of work you are do- ing '[he nickel,.cadmium batteries in this tool have been designed to last for the life of the unit under normal operating conditions. Therefore, do not disassemble your drill and attempt to replace them, Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn WRIST STRAP A wr
Résumé du contenu de la page N° 7
OPERATION (Cont.) INSTALLING BITS ---- .... 1 Lock switch trigger on your ddtt by placing the direction of rotation selector in center position. 2 Close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use, 3 insert your drilJ bit into chuck the full length of the jaws as shown in Figure 4, BIT CHUCK KEY 4" Remove chuck key from chuck key storage See HOLE Figure 3 WRIST 5 Tighten chuck jaws by placing chuck key tn each o! the three holes, and tighten in
Résumé du contenu de la page N° 8
OPERATION (Cont.) DRILLING The material to be drilled should be secured in a vise or with ciamps to keep it from turning as the drill bit rotates Hold your drill lirmly and place the bit at the point te be drilled, Depress the switch trigger to start your drill Move the drill bit into the workpiece applying only enough pressure to keep the bit cutting Do not force your drill or apply side pressure to elongate a hoie Let your drill and bit do the work See Fig 8 When drHting metals use a light oil
Résumé du contenu de la page N° 9
MAINTENANCE GENERAL Avoid using solvents when cleaning plastic parts Most plastics are susceptible to various types of oommeP cial solvents and may be damaged by their use, Use clean cloths to remove dirt, dust, oil, grease, etc, ACCESSORIES ...... THE FOLLOWING RECOMMENDED ACCESSORIES ARE CURRENT AND WERE ............. AVAILABLE AT THE TIME THIS MANUAL WAS PRINTED, t3,Pc, Power Screwdriver/Nutdriver Set and Case 5,,Pc, Power Screwdriver Bit Set Cat No,, 9 25653 Cat, No 9 25602 30-Pc Power Screw
Résumé du contenu de la page N° 10
NOTES Page 10
Résumé du contenu de la page N° 11
NOTES Page 11
Résumé du contenu de la page N° 12
1" 3/8 INCH OWNERS CORDLESS DRILL MANUAL SINGLE-SPEED REVERSIBLE SERVICE Now that you have purchased your Drill, shoutd a need ever exist for tepai[ parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co, stores Be sure to provide all perti- nent facts when you call or visit. MODEL NO. The model number of your Drill wiil be found on the plate attached to the motor housing. 315.111450 WHEN ORDERING REPAIR PARTS, ALWAYS GIVE HOW TO ORDER THE FOLLOWING INFORMATION:
