Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
Commercial Snowblower TABLE OF CONTENTS DESCRIPTION PAGE Warranty......................................................................1 Safety Instructions ....................................................... 2 Safety Signs & Safety Sign Locations.......................... 3 Operating Instructions.................................................. 5 Hydraulic Control Block Instruct
Résumé du contenu de la page N° 4
Commercial Snowblower WARRANTY POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months (90 days for commercial application) from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications. Buhler Manufacturing’s obligations under this warranty shall be limited to the repai
Résumé du contenu de la page N° 5
Commercial Snowblower SAFETY INSTRUCTIONS CAUTION 1. Always review operator’s manual before starting new machine. 2. Do not let inexperienced operators or children run this equipment. 3. Never service or clean unit while it is running. 4. Do not remove shields. 5. Stay clear of augers. 6. Stay clear of discharge chute. Rocks can be picked up and thrown. 7. Do not operate in the fully
Résumé du contenu de la page N° 6
Commercial Snowblower SNOWBLOWERS This manual is for both Commercial Hydraulic Snowblowers and Commercial PTO Drive Snowblowers. The hydraulic models come in 60”, 66”, 74” and 84” widths. The PTO drive model is only available in an 84” width. Hydraulic models come with four different motor series. Hydraulic output on the equipment running the Snowblower must match the requirement for each motor series f
Résumé du contenu de la page N° 7
Commercial Snowblower SAFETY SIGNS #1 #3 #3 Replace safety signs immediately should they become damaged, torn or illegible. Obtain replacements from your authorized dealer using the part numbers shown. #4 4
Résumé du contenu de la page N° 8
Commercial Snowblower OPERATING INSTRUCTIONS 1. HYDRAULIC DRIVE: All snowblower hydraulic blocks are set at the factory for a 2800 - 3000 psi system. Refer to the section on the hydraulic control block if your system does not fall into this range. 2. ALL: Depth of the cut can be partially controlled by tilting the snowblower forward or backward. 3. PTO DRIVE: Adjust the top link of the tractor hit
Résumé du contenu de la page N° 9
Commercial Snowblower OPERATING INSTRUCTIONS – cont’d. 10. ALL: Chain tension on auger chain should be set at 3/8” to 1/2” slack. 11. LUBRICATION: a) ALL: The gear teeth on the chute control should be periodically lubricated with gun grease. b) PTO DRIVE: PTO shaft universal joints and square shaft slide should be periodically lubricated with a grease gun. c) ALL: Regularly oiling the chain will si
Résumé du contenu de la page N° 10
Commercial Snowblower HYDRAULIC CONTROL BLOCK NON-STALLING-FAN FEATURE: The Hydraulic Snowblower has a unique modulating element that keeps the blower fan from stalling in an overloaded condition. This is accomplished by starving the hydraulic flow to the front auger motor (which then stops feeding the fan) and diverts all of the flow (and energy) to the main fan motor. As the fan clears itself, and the
Résumé du contenu de la page N° 11
Commercial Snowblower HYDRAULIC CONTROL BLOCK DRAWING AND PARTS LIST HYD MANIFOLD ASSEMBLY Item # Part # Description 1 905669 Main Block 2 813922 Logic Element 3 X2732 Element Seal Kit 4 813923 Control Valve 5 X2733 Seal Kit 6 813924 No-Load Valve 7 X2734 Seal Kit 8ab 813925 Chute Cont. Valves 9 X2735 Seal Kit 10a 813926 No-Load Press. Coil 10bc 813926 Chute Up Down Coil 10ef 813926 Chut
Résumé du contenu de la page N° 12
Commercial Snowblower ASSEMBLY INSTRUCTIONS 1. SPOUT ASSEMBLY FOR ALL SNOWBLOWERS: Remove two of the grooved spout rollers to mount the discharge spout. Replace the two rollers to hold spout in place. Install the 2 ½” x 8” cylinder on the spout using the pins supplied. 2. HYDRAULIC DRIVE: (Page 21 & 22) The 80” long hydraulic lines (#14) for the spout deflector cylinder should be connected to the two
Résumé du contenu de la page N° 13
Commercial Snowblower ASSEMBLY INSTRUCTIONS – cont’d. b) Using tape or a bright colored marking pen, mark on the outer shields the position where the shaft is completely pushed together and the position where you have a 4” overlap. Watch these marks when moving the blower through all possible operating angles to see that the PTO shaft stays within this range. c
Résumé du contenu de la page N° 14
Commercial Snowblower ASSEMBLY INSTRUCTIONS – cont’d. 4. PTO SHIELD: All PTO snowblowers are supplied with a PTO shield (#18). To install, remove the two rear bolts at the top of the gearbox (#34). Bolt the PTO shield to the gearbox by the hinges using these same bolts. A utility spring (#68) keeps the shield in place. Hook one end of the spring in the hole in the shield and the other end
Résumé du contenu de la page N° 15
Commercial Snowblower HYDRAULIC COMMERCIAL SERIES SNOWBLOWER – 22” HOUSING 12
Résumé du contenu de la page N° 16
Commercial Snowblower 13
Résumé du contenu de la page N° 17
Commercial Snowblower WHEN ORDERING PARTS Always give your dealer the Model, Color and Serial Number of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part. Hyd Commercial Series Snowblower - 22'' Housing Item # Part # Description 1 905536 Main Body Weldt - 74'' 909590 Main
Résumé du contenu de la page N° 18
Commercial Snowblower 22 905224 Fan Shaft 1 1/2'' x 15 1/4'' 23 22695 Chain Cover 909593 Chain Cover - 66" 24 902407 Skid Plate Weldt 909594 Skid Plate Weldt Lh - 66" 909610 Skid Plate Weldt Rh - 66" 25 103753 Cylinder Clevis Pin 1'' x 4'' 26 12779 Hair Pin Clip #9 Western Wire 27 960719 Sprocket 15T, #80, 1 1/2'' Bore 28 905309 Sprocket 15T, #80, 1 1/4'' Bore (Ser 1-3) 960719 Sprocket 15T, #80, 1
Résumé du contenu de la page N° 19
Commercial Snowblower 61 81677 5/8'' Lock Washer (pl) 62 81678 5/8'' BS Flat Washer Std (pl) 63 965821 3/8'' x 1 3/4'' Key 64 905310 3/8'' x 4 1/2'' Key 65 900712 Skid Pin Weldt 5/8'' x 3'' 66 961012 #16 Hair Pin Clip (pl) 67 905278 Cover Plate 68 905336 Fan Housing Liner 68'' 69 906348 Motor Washer 13/32'' hole x 2'' OD 70 906574 Bronze Bushing 7/8'' OD x 1'' 71 812026 5/16'' x 1'' Hex Bolt (pl) 72 90
Résumé du contenu de la page N° 20
Commercial Snowblower HYDRAULIC COMMERCIAL SERIES SNOWBLOWER – 24” HOUSING 17
