Résumé du contenu de la page N° 1
Instructions for
WASHER DRYER
installation and use
! This symbol reminds you to read this instruction manual.
EN
Contents
EN
English,1
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
Technical data
Description of the machine, 6-7
Control panel
How to run a wash cycle or a drying
cycle, 8
Wash cycles and options, 9
Table of wash cycles
Wash options
Detergents and laundry, 10
Detergent
AQUALTIS
Preparing the laundry
Washing recommendations
AQD1170F 69
Résumé du contenu de la page N° 2
Installation ! This instruction manual should be kept in a safe place for ! If the appliance is levelled correctly, it will be more stable EN future reference. If the washer-dryer is sold, given away or and much less likely to cause vibrations and noise while it moved, please ensure the manual is kept with the machine, is operating, particularly during the spin cycle. so that the new owner may benefit from the advice ! If it is placed on carpet or a rug, adjust the feet in such a contained wi
Résumé du contenu de la page N° 3
65 - 100 cm Connecting the drain hose • the supply voltage is included within the values indica- EN ted on the Technical Data Plate fixed on the machine. Connect the drain hose, • the socket is compatible with the washer-dryer’s plug. If without bending it, to a this is not the case, replace the socket or the plug. draining duct or a wall drain situated between Your appliance is now supplied with a 13 amp fused plug 65 and 100 cm from the it can be plugged into a 13 amp socket for im
Résumé du contenu de la page N° 4
As the colours of the wires in the lead may not correspond EN with the coloured markings identifying the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or or coloured Green or Green & Yellow. Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board. If you a
Résumé du contenu de la page N° 5
EN Technical data AQD1170F 697 E Model AQD1170F 697 I width 59.5 cm Dimensions height 85 cm depth 64.5 cm from 1 to 11 kg for the wash programme Capacity from 1 to 7 kg for the drying programme Electrical please refer to the technical data plate fixed to the machine connections maximum pressure 1 MPa (10 bar) Water connections minimum pressure 0.05 MPa (0.5 bar) drum capacity 71 litres Spin speed up to 1600 rotations per minute Wash: programme ; temperature 60°C; Energy rated using a load of
Résumé du contenu de la page N° 6
Description of the machine EN CONTROL PANEL PORTHOLE DOOR PORTHOLE DOOR HANDLE KICK STRIP ADJUSTABLE FEET PORTHOLE DOOR ! Do not pour detergent into A the compartment 1. Always use the handle to Detergent should only be open the porthole door (see 1 poured into the compartment 2. figure). 2. main wash compartment: 2 B If liquid detergent is used, it is recommended that the removable plastic partition A (supplied) be used for proper dosage.If powder detergent is used, place the parti
Résumé du contenu de la page N° 7
Control panel WASH EN ECO CYCLE indicator light PHASE START/ icons PAUSE OPTION buttons OPTION buttons button with WASH CYCLE with indicator lights with indicator lights indicator light SELECTOR knob DISPLAY CHILD LOCK DELAY Button with ON/OFF TEMPERATURE button button with indicator light TIMER indicator light LOCK button indicator light DRY button START/PAUSE button with indicator light: when the green Button with ON/OFF indicator light: press this briefly indicator light
Résumé du contenu de la page N° 8
How to run a wash cycle or a drying cycle WARNING: before you use the wasdher-dryer for the first Drying only EN time, run a wash cycle with detergent and no laundry, using Use the cycle selector knob to select a drying cycle the 90° cottons cycle without pre-wash. ( - - ) in accordance with the type of fabric. The desired drying level or time may also be set using the 1. SWITCH THE MACHINE ON. Press the button. DRYING button . All the indicator lights will illuminate for 1 second; the
Résumé du contenu de la page N° 9
(*) The duration of the wash cycles can be checked on the display. Wash cycles and options Table of wash cycles EN Detergent and Max. Max. additives Max. temp. Cycle Icon Description of the wash cycle speed Drying load (°C) Fabric duration (rpm) Wash (kg) softener Cottons (2): lightly soiled whites and delicate colours. 40° 1600 11 Synthetics 60° 800 5 Synthetics (4) 40° 800 5 Whites 60° 1600 6 Coloureds (3) 40° 1600 6 Darks 30° 800 6 Refresh - - - - - 2
Résumé du contenu de la page N° 10
Detergents and laundry Refresh: this programme refreshes garments by removing Detergent EN bad odours and relaxing the fibres (2 kg, roughly 3 The type and quantity of detergent required depend on items). Insert dry items only (that are not dirty) and select the type of fabric you are washing (cotton, wool, silk, etc.), programme “ “. The garments will be damp once the as well as its colour, the washing temperature, the level of cycle is completed, so we recommend hanging them to soiling
Résumé du contenu de la page N° 11
Precautions and tips ! The machine was designed and constructed in Load balancing system EN accordance with international safety regulations. The Before every spin cycle, to avoid excessive vibrations following information is provided for safety reasons and before every spin and to distribute the load in a uniform must therefore be read carefully. manner, the drum rotates continuously at a speed which General safety is slightly greater than the washing rotation speed. If, • This appliance
Résumé du contenu de la page N° 12
Care and maintenance To access the pre-chamber: Cutting off the water and electricity EN supplies • Turn off the water tap after every wash cycle. This will 1 limit wear on the hydraulic system in the machine and help to prevent leaks. • Unplug the appliance when cleaning it and during all maintenance work. 2 Cleaning the machine 1. take off the cover panel on the front of the machine by first pressing it in the centre and then pushing downwards The outer parts and rubber components of th
Résumé du contenu de la page N° 13
Trouble shooting Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), EN make sure that the problem cannot be solved easily using the following list. Problem: Possible causes / Solutions: The machine does not switch on. • The appliance is not plugged into the socket fully, or not enough to make contact. • There is no power to the socket, or the fuse has blown in the mains plug. The wash cycle does not start. • The door is no
Résumé du contenu de la page N° 14
The machine wont spin properly. • Out of Balance detected when attempting to go into a spin cycle - If this EN happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds - This will increase the programme time accordingly. This is a safety feature to prevent damage. Out of Balance can be caused by washing a single heavy item (eg duvet, quilt, etc). - Try the programme again using a different load. The machine
Résumé du contenu de la page N° 15
Assistance Guarantee EN 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the date of purchase. This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you. This guarantee is subject to the following conditions:
Résumé du contenu de la page N° 16
195098453.01 12/2012 - Xerox Fabriano EN After Sales Service No one is better placed to care for your Hotpoint appliance during the course of its working life than us - the manufacturer. Essential Contact Information Hotpoint Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000 fully qualified engineers on call to ensure you receive fast, reliable, local service. UK: 08448 224 224 Republic of Ireland: 0818 313 413 www.hotpointserv
