Résumé du contenu de la page N° 1
ISSUED: JAN. 22, 2003
REVISED: JUN. 20, 2005
HOSHIZAKI
SELF-CONTAINED CUBER
MODEL AM-100BAE
AM-150BAF
AM-150BWF
INSTRUCTION MANUAL
Résumé du contenu de la page N° 2
FOREWORD IMPORTANT Only qualified service technicians should attempt to install, service or maintain this icemaker. No such installation, service or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual. Likewise, the owner/ manager should not proceed to operate the icemaker until the installer has instructed them on its proper operation. HOSHIZAKI provides this manual primarily to assist qualified service technicians in the installation, maintenance a
Résumé du contenu de la page N° 3
IMPORTANT 1. This booklet is an integral and essential part of the product and should be handed over to the user. Read the warnings contained in this booklet carefully as they give important indications regarding the safety of the installation, use and maintenance. Please preserve this booklet for any further consultation that may be necessary. 2. This icemaker should be destined only to the use for which it has been expressly conceived. Any other use should be considered improper and therefo
Résumé du contenu de la page N° 4
I. GENERAL INFORMATION 1. CONSTRUCTION [a] AM-100BAE Top Panel Front Panel (Upper) Ice Making Mechanism Bin Control Thermostat Storage Bin Slope Door Front Panel (Lower) Control Box Condenser Air Filter Tapped Hole (Leg Mounting) Control Switch Fuse 1
Résumé du contenu de la page N° 5
[b] AM-150BAF Top Panel Ice Making Mechanism Separator Water Tank Bin Control Thermostat Slope Door Storage Bin Front Panel (Lower) Control Box Condenser Air Filter Tapped Hole (Leg Mounting) Control Switch Fuse 2
Résumé du contenu de la page N° 6
[c] AM-150BWF Top Panel Ice Making Mechanism Separator Water Tank Bin Control Thermostat Slope Door Storage Bin Front Panel (Lower) Control Box Condenser Tapped Hole (Leg Mounting) Control Switch Fuse 3
Résumé du contenu de la page N° 7
II. INSTALLATION AND OPERATING INSTRUCTIONS 1. CHECKS BEFORE INSTALLATION * Visually inspect the exterior of the shipping container, and any severe damage noted should be reported to the carrier. WARNING 1. Remove shipping tape(s) and packing as follows. If any left in the icemaker, it will not work properly. 2. Do not lift or carry the unpacked icemaker by using the brass fitting for water supply at the rear of the unit. The plastic threads may be damaged. IMPORTANT 1. Remove the shipping tap
Résumé du contenu de la page N° 8
2. LOCATION WARNING This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within 50°F (10°C) to 100°F (38°C); Normal operating water temperature should be within 41°F (5°C) to 90°F (32°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect production capacity. For best operating results: * The icemaker should not be located next to ovens, grills or other high heat producing equipment. * The location sh
Résumé du contenu de la page N° 9
3. SET UP IMPORTANT Do not place heavy objects exceeding 33 lbs (15 kg) on the Top Panel. 1) Unpack the icemaker, and remove all shipping cartons, tapes and packing BEFORE operating the unit. 2) Position the icemaker in a selected site. Clean the interior with soap and water and rinse thoroughly. 3) Level the icemaker in both the left-to-right and the front-to- Max. 0.4” (1 cm) rear directions (when installed with or without legs). See Fig. 2. Fig. 2 4) When installing the unit without legs, t
Résumé du contenu de la page N° 10
5. WATER SUPPLY AND DRAIN CONNECTIONS WARNING To prevent damage to the freezer mechanism, do not operate this icemaker when the water supply is OFF, or if the pressure is below 10 PSIG (0.7 bar), the recommended water pressure. Stop the icemaker until proper water pressure is resumed. CAUTION 1. A brass fitting for the water supply line connection is attached to the 3/4” BSP plastic threads to avoid cross-threading of the Water Valve possibly resulting in leaks. The brass fitting allows connec
Résumé du contenu de la page N° 11
* A plumbing permit and services of a licensed plumber may be required in some areas. * This icemaker should be installed in accordance with applicable national, state and local regulations. AM-100BAE AM-150BAF Icemaker Water Supply Inlet 3/4” BSP Threads Brass fitting is attached to Water Supply Inlet. Fitting size is a 1/2” FPT. Shut-off Valve Drain Valve Bin Drain Outlet 3/4” FPT Trap 1/4” fall per foot To approved floor drain AM-150BWF Icemaker Water Supply Inlet 3/4” BSP Threads Condenser O
Résumé du contenu de la page N° 12
6. FINAL CHECK LIST 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within 50°F (10°C) to 100°F (38°C) and the water temperature within 41°F (5°C) to 90°F (32°C) all year around? 3) Have all shipping tape(s), string and packing been removed from the icemaker? 4) Are all components, fasteners and thumbscrews securely in place? 5) Have all electrical and piping connections been made? 6) Has the power supply voltage been tested or checked against the nameplat
Résumé du contenu de la page N° 13
8. PREPARING THE ICEMAKER FOR LONG STORAGE (more than 1 day) WARNING Drain the icemaker to prevent damage to the water supply line at subfreezing temperatures, using air or carbon dioxide. Shut off the icemaker until proper air temperature is resumed. [1] On water-cooled model only, first remove the water from the water-cooled condenser: 1) Remove the Front Panel (Lower). Icemaker Potable Water Supply Line 2) Move the Control Switch, on the Control Box, to the “OFF” position. 3) Wait 3 minutes.
Résumé du contenu de la page N° 14
3) Blow out the water supply line. Note: This procedure is necessary to protect the icemaker from freezing up at subfreezing temperature. 4) Unplug the icemaker. 5) Remove all ice from the Storage Bin, and clean the Bin. 6) Drain and clean the Water Tank. See “III. 1. [b] STORAGE BIN, SLOPE, SCOOP, ETC.” 7) Refit the Front Panel (Lower) in its correct position. 8) Close the Drain Valve. 11
Résumé du contenu de la page N° 15
III. MAINTENANCE AND CLEANING INSTRUCTIONS IMPORTANT Ensure all components, fasteners and thumbscrews are securely in place after any maintenance or cleaning is done to the equipment. 1. CLEANING INSTRUCTIONS WARNING 1. HOSHIZAKI recommends cleaning this unit at least once a year. More frequent cleaning, however, may be required in some existing water conditions. 2. To prevent injury to individuals and damage to the icemaker, do not use ammonia type cleaners. 3. Always wear liquid-proof gloves
Résumé du contenu de la page N° 16
8) Remove the Water Tank to drain the cleaning solution. Refit the Water Tank in its correct position. 9) Open the Shut-off Valve. 10) Move the Control Switch to the “WASH” position to circulate clean water for about 5 minutes. 11) Move the Control Switch to the “OFF” position and immediately back to the “WASH” position to rinse water. 12) Repeat the above rinse procedure three more times to rinse thoroughly. 13) Dilute approximately 0.5 fl. oz. (14.8 ml) of 5.25% Sodium Hypochlorite (Chlorine
Résumé du contenu de la page N° 17
[b] STORAGE BIN, SLOPE, SCOOP, ETC. IMPORTANT 1. Wash your hands before removing ice. Use the Plastic Scoop provided to remove ice. 2. Keep the Scoop clean. Clean it by using a neutral cleaner at least once a day, and rinse thoroughly. 3. Close the Bin Door after removing ice to prevent entrance of dirt, dust or insects into the Bin. 4. Clean the Bin Liner at least once a month by using a neutral cleaner. Rinse thoroughly after cleaning. 5. The Storage Bin is for ice use only. Do not store a
Résumé du contenu de la page N° 18
8) Remove the Thumbscrews on both sides of the Water Tank, and pull it out toward you. Clean and sanitize the Water Tank. Water Tank Thumbscrew Water Plate 9) Pull the Discharge Tube from the Water Plate. Remove the Water Plate by pulling it toward you. Discharge Tube 10) Remove the Caps to clean and sanitize the Water Plate. If the Nozzles are clogged, clean them with a wire or a suitable brush. Cap Water Plate 11) Refit the Caps on the Cleaning Outlets to seal them off. Cap Water Plate Water
Résumé du contenu de la page N° 19
15) Hook each Separator on to the Mechanism Separator Base, and pull it hard toward you until it locks in place with a click. Refit all the Separators in the same way. 16) Refit the Slope in its correct position. 17) Plug in the icemaker, and move the Control Switch on the Control Box to the “ICE” position to start the automatic icemaking process. 18) Refit the Front Panel (Lower) in its correct position. 2. MAINTENANCE IMPORTANT This icemaker must be maintained individually, referring to the i
Résumé du contenu de la page N° 20
SERVICE INSTRUCTIONS Bin Control Thermostat Replacement Procedure To ensure proper operation, follow the instructions below: [AM-100BAE] [AM-150BAF/BWF] 1) Make a 40 mm (1.6”) diameter loop. 1) Make a 40 mm (1.6”) ID U-bend. 2) Locate the loop below the Thermostat 2) Locate the U-bend 60 mm (2.4”) below Capillary (Bulb). the Thermostat Capillary (Bulb). 3) Manually bend the Capillary to keep it 3) Manually bend the Capillary to keep it 15 mm (0.6”) forward from the throu
