Résumé du contenu de la page N° 1
JUN. 2002 PRINTED IN KOREA P/No.:3828EA3013E
Résumé du contenu de la page N° 2
WASHING MACHINE SERVICE MANUAL CAUTION Before servicing the washer, Read the safety precautions in the manual. MODELS : WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3) WF-T802/T852(A)/T853A WF-T(F/C)1091~3, 1191~3T(C/H/P) WF-T(F/C)1022, 1122, 1001T(C/H/P) WF-T1268TH, 2409KTb, 2602kTa WF-T1491TP, T11292TP, T1292TP, T1291TP WF-T1081TP, T1592TP, T1593TP WF-T1241TP, T1133TH WF-G15KTB, G13KTC, B15KTB, B13KTC WF-T1400TH, T1022TPX
Résumé du contenu de la page N° 3
SAFETY PRECAUTION! ■ DISASSEMBLE POWER CORD BEFORE SERVING ■ RECONNECT ALL GROUNDING DEVICES IMPORTANT SAFETY NOTICE ! This service information is intended for individuals possessing adequate backgrounds of electrical, electronic and mechanical experience. Any attempt to repair this appliance may result in personal injury or property damage. The manufacturer or seller can not be responsible for the interpretation of this information, nor can it assume any liability in connection with its use
Résumé du contenu de la page N° 4
1. SPECIFICATIONS WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3), WF-T802/T852(A)/T853A Model WF-T(F/C)1091~3/1191~3T(C/H/P), WF-T(F/C)1022/1122/1001T(C/H/P) WF-T1268TH/2409KTb/ 2602kTa/T1491TP/T1022THX/T1133TH WF-T1081TP/T1491TP/T11292TP/T1292TP/T1291TP/LA-1499ST/T1592TP/T1593TP/T1241TP WF-G15KTB/G13KTC/WF-B15KTB/B13KTC/WF-T1400TH/T1022TPX Power Sourse Refer to rating label on the back of Washer Input Refer to rating label on the back of Washer Capacity Refer to rating label on the back of Washer Inner T
Résumé du contenu de la page N° 5
2. INSTALLATION INSTRUCTIONS 2-1. HOW TO ADJUST LEVEL Installation area 1 ·Install the washer on flat and firm surface. Checking level 2 ·Open the lid, and check if the washer is correctly leveled by looking down from the top. Adjustable leg Turn the adjustable legs to set the washer horizontal (2 EA). How to use the adjusting plates · Use the adjusting plates to level the washer when the adjustable legs cannot cover the gap. Improper installation of the washer may cause noise and malfunctioni
Résumé du contenu de la page N° 6
Checking slope Confirming level 35 · Place the washer to original position · If installation surface is tilted, the and confirm the level. washer will be shaken. Horizontal setting Distance between drain hose and the wall 4 · Distance between drain hose and the wall ·Lift up the front of the washer and should be more than 10 cm, and the distance adjust level by turning the adjustable between the other part and the wall should be legs clockwise or using the adjusting more than 2 cm. More than
Résumé du contenu de la page N° 7
2-2. CONNECTING WATER SUPPLY HOSE Before connecting Water Supply Hose to water tap, check your hose type and choose correct instruction. Water Supply Hose may vary according to the country. Make sure connect blue inlet hose to cold water tab, and orange inlet hose to hot water tab. Connecting Water Supply Hose to water tap Normal Type Normal tab without thread & screw type inlet hose.) Rubber packing Untighten the screw 1 Untighten the screw of the connector so that the tap can be placed in
Résumé du contenu de la page N° 8
One Touch Type (NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.) Separate Middle connector from Water Supply Hose 1 Separate Middle connector from the Water Middle Fixed Stiicker connector Supply Hose by pulling the Pressing Rod and Pressing Handle the Pressing Handle that is attached to the Pressing Rod Water Supply Hose while pressing them. Water Supply Hose Loosen the fixed nuts to connect the connector to the tap 2 Untighten the screw of the connector so that Rubber packing Screw the
Résumé du contenu de la page N° 9
Screw Type Attach the water supply hose to the tap. 1 Push the water supply hose up so that the Water rubber packing within the hose can adhere tap completely to the tap. Rubber Packing Water Supply Hose Connect the water supply hose to the tap. 2 Connect the water supply hose to the tap and then tighten it by screwing it to the right. Check water leakage. 3 After connecting the hose, open the faucet to check for any water leakage. Connecting Water Supply Hose to the machine Connect the water su
Résumé du contenu de la page N° 10
Within 50mm 2-3. CONNECT THE DRAIN HOSE ■ For pump model · Connect the drain hose to ·Attach the clip to the drain ·Check that the drain hose is the outlet of the drain pump hose. And then push it toward hung up over the edge of the located at the rear of the the body of the washing laundry tub. washing machine. machine as indicated by the ·Do not use an extension hose. arrow. Hose Guide 0.9~1.2m Drain Hose · NOTE : · Never lay down the drain hose, as water will be discharged. · Be sure the drai
Résumé du contenu de la page N° 11
3. OPERATING INSTRUCTIONS 3-1. IDENTIFICATION OF PARTS WATER SUPPLY HOSE SOFTENER DISPENSER • Make sure that water does • Softener will automatically not leak. flow into the tub. • In case of one valve model water supply hose is one. DETERGENT DISPENSER POWER SUPPLY CORD BLEACH INLET FUNCTION SELECTORS DRAIN HOSE For Pump Model • Check out if the drain hose is PULSATOR hung up before operating the ANTI RAT BASE washing machine. DRAIN HOSE For non Pump Model ADJUSTABLE LEG • Keep downward whi
Résumé du contenu de la page N° 12
3-2. BEFORE STARTING TO WASH Care Labels * Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. Sort clothes into loads that can be washed with the same wash cycle, water temperature and spin speed. Sorting To get the best results, different fabrics need to be washed in different ways. • SOIL (Heavy, Normal, Light) Separate clothes according to the type and amount of soil. • COLOR (Whites, Lights, Darks) Separate white
Résumé du contenu de la page N° 13
Using Water Amount of Water Level • This machine detects the quantity of laundry automatically, then sets the water level and WATER - DETERGENT EX-LARGE proper amount of detergent. LARGE • When you select a wash program, the water level and amount of detergent (to be used) MEDIUM will be shown on the control panel. SMALL • The following table shows the amount of water. • When the water level is automatically detected, it may differ depending on the quantity of laundry even though the same wat
Résumé du contenu de la page N° 14
Using Detergent How much detergent When you select a wash program the water level and the amount of detergent (to be used) will be shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated detergent. The correct amount of detergent will vary depending on the amount of soil in your clothes (Jeans and work cloches may need more detergent, while bath towels usually need less.). For liquid and concentrated detergents, follow the recommendations of the detergent
Résumé du contenu de la page N° 15
Using Fabric Softener Available Fabric Softener Type • Do not use concentrated fabric softener. This may cause some problems in automatic dispensing. • For more details refer to the softener products instructions for use. Depositing Fabric Softener Powder Detergent & Fabric Softener dispenser. • Don't use softener with detergent. Use softener in last rinse water Where you deposit the softener • When using dispenser, dilute softener (30ml) with fresh water (30ml) • When filling dispenser, do not
Résumé du contenu de la page N° 16
Special Guide for Stain Removal WARNING ■ Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death. ■ To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below: • Read and comply with all instructions on stain removal products. • Keep stain removal products in their
Résumé du contenu de la page N° 17
3-3. FUNCTION OF EACH BUTTON ▶ Changing various functions is possible only in PAUSE state. Selection button does not work when the washer is in operation (Except for water level, water temp, water power button). How to use delayed Detergent deposit Wash Process display washing display ■ Use this function for delayed ■ Upon loading laundry, it ■ Indicates the current washing washing. displays the correct amount of status. ■ Use it to set the delay time. detergent to be added ■ Next step is lit,
Résumé du contenu de la page N° 18
For manual wash, rinse Displaying abnormal operation and spin ■ In case of abnormal operation, the following indications are displayed. ■ Wash : Use it to change washing time. Abnormal water supply : INLET Er. lamp blinks. By pressing the button[ 15min → Abnormal drainage : DRAIN Er. lamp blinks. 18min →21min →25min →40min → Abnormal spin : SPIN Er. lamp blinks. 60min →90min →OFF →3min →6min →9min →12min →15min]SOAKING is used to Abnormal water level sensing : displayed. remove old or hardened d
Résumé du contenu de la page N° 19
3-4. WASHING PROGRAMS AUTO OFF Washing Add PRO - Add GRAM Programs the laundry the deterg 1 2 Fuzzy Washing (Normal Wash) Used for normal loads, this mode ·Add the appropriate automatically selects the most appropriate detergent as indicat conditions and completes the sequence in water level next to W one operation. The built-in sensor detects the DETERGENT. size of the load and the ideal wash power and Or follow the deterg wash, rinse and spin times are set accordingly manufacturer’s inst Bla
Résumé du contenu de la page N° 20
START Close the lid Finish Caution & Note PAUSE t ·If water is already in the tub, or putting wet laundry 3 5 6 into the tub before starting will increase the water level. antity of ·The pulsator rotates for 8 seconds to ·Water will be supplied for 2 ·When the wash program by the detect the laundry load. ·With lightweight bulky loads, water level can be set minutes after the start of the ends, the buzzer will ring for TER- ·Then the water level and the amount of wash to supplement the low. 10 s
