Résumé du contenu de la page N° 1
Washing Machine
OWNER'S MANUAL
WD13020D
WD12020D
WD11020D
Thank you for buying a
LG Fully Automatic Washing machine.
Please read your owner's manual carefully, it provides
instructions on safe installation, use and maintenance.
Retain it for future reference.
Record the model and serial numbers of your washing
machine.
Résumé du contenu de la page N° 2
roduct Features P Protection against creases With the alternate rotation of the drum, creasing in the laundry is minimized. Built-in Heater Internal heater automatically heats the water to the best temperature on selected cycles. More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption. Child Lock The Child lock prevents child
Résumé du contenu de la page N° 3
arnings W READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE For your safety, the information in this manual must be followed to minimize WARNING! the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. IMPORTANT SAFETY INSTRUCTIONS WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: • Before installation,
Résumé du contenu de la page N° 4
pecifications S Name : Front loading washing machine Power supply : 220-240V~,50Hz Size : 600mm(W) 550mm(D) 850mm(H) Weight/Max.Watt : 58kg / 2100W Wash capacity : Refer to the Rating Label Water consumption : 64 Permissible water pressure : 1.0-8 bar (100-800kPa) Spin speed : No Spin/400/800/1300 [WD13020D] No Spin/400/800/1200 [WD12020D] No Spin/400/800/1100 [WD11020D] The external hot water supply MUST NOT exceed 70 deg C Permissible cold water temperature : 4-25˚C N
Résumé du contenu de la page N° 5
nstallation I Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in clean condition a
Résumé du contenu de la page N° 6
nstallation I Installation place requirement Level floor : Drain Hose Allowable slope under entire washer is 1˚ Washer Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Laundry Tub Additional Clearance : approx. Allow 10cm of clearance at the rear of the machine and 2cm 2cm at each side. Do not place or store laundry products on top of washer at any time. Do not use pre wash stain remonal chemicals on or near
Résumé du contenu de la page N° 7
nstallation I Electrical connection 1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents in order to avoid a hazard. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible. • Repairs to the washing machine must only be carri
Résumé du contenu de la page N° 8
nstallation I Normal Tap without thread & screw type inlet hose 1. Unscrew the fixing screw to 2. Push the connector up till the 3. Push the water supply hose attach the tap. rubber packing is in tight contact vertically upwards so that the with the tap. Then tighten the 4 rubber packing within in the screws. hose can adhere completely to the tap and then tighten it by screwing it to the right. Normal Tap without thread & one touch type inlet hose (Single inlet models) 1. Untighten the upper
Résumé du contenu de la page N° 9
nstallation I This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the supply tap if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous f
Résumé du contenu de la page N° 10
nstallation I Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. Timber or suspended type flooring may contribute to NOTE excessive vibration and unblance errors. 2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and
Résumé du contenu de la page N° 11
are before washing C Preparations for the first wash Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues and water from the drum that may have been left during manufacturing. Caring before washing 1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the best results, Sort clothes into loads that can be washed wi
Résumé du contenu de la page N° 12
dding detergent A Adding detergent and fabric softener 1. The Dispenser Drawer • Main wash only ➔ • Pre Wash + Main Wash ➔ max 2. Adding Fabric Softener • Do not exceed the maximum fill line. Close the dispenser drawer slowly. Overfilling can cause early dispensing of the fabric softener which could stain clothes. • Do not leave the fabric softener in the detergent drawer for more than 2 days. (Fabric softener could harden) • Softener will automatically be added during the last rinse cycle. •
Résumé du contenu de la page N° 13
dding detergent A [Important Note] 3. Detergent dosage Recommended amount of detergent as per wash load • The detergent should be used according to the instruction of the detergent manufacture. Water quality and temperature will play a major part on how much detergent is • If too much detergent is used, too many suds can required. Follow the detergent manufacturer's occur and this will decrease the washing result recommendation as a guide, however, Less or cause heavy load to the motor. (Causing
Résumé du contenu de la page N° 14
unction F Recommended courses according to the laundry type Program Fabric Type Proper Temp. Option Maximum Load Color fast garments 40˚C (shirts, night dresses, Less than Cotton (Cold, 30˚C, pajamas...)and lightly soiled white 8.0 kg 60˚C, 95°C) cotton(underwear) - Medic Rinse Less than - Intensive Synthetic Polyamide, Acryic, Polyester - Pre Wash 4.0 kg 40˚C - Crease Care (Cold, 30˚C, Less than 60˚C) Cotton which is lightly soiled Cotton Quick 8.0 kg Colored Laundry which is lightly 30˚C
Résumé du contenu de la page N° 15
ow to use washer H 2. Manual Selecting 1. Cotton automatically selected upon power on. • Press the Power button to start. • Select the desired program cycle and options • Press the Power button to start. by turning the program dial and pressing • Press the Start/Pause button. each button. Please refer to page 16 ~ 21 on how to set the • Initial conditions program and options. - Wash : main wash • Press the Start/Pause button. - Rinse : 3 times - Spin : • 1300 rpm [WD13020D] 3. Beep on/off • 120
Résumé du contenu de la page N° 16
ow to use washer H (1) Dial : Program (5) Button : Power (9) Button : Crease Care (2) Button : Start / Pause (6) Button : Medic Rinse (10) Child Lock (3) Button : Spin (7) Button : Pre Wash (11) Tub Clean (4) Button : Temperature (8) Button : Intensive (12) Button : Time Delay Power Program 1. Power • Press the Power button to turn power on and off. • To cancel the Time Delay function, the power button should be pressed. • 13 programs are available according to the 2. Initial Program laundry typ
Résumé du contenu de la page N° 17
ow to use washer H Start/Pause Option • By pressing the Option button, Option functions may be selected. 1. Start • This Start/Pause button is used to start wash cycle or pause the wash cycle. 2. Pause 1. Medic Rinse • If temporary stop of wash cycle is • This option allows the final rinse to be heated needed, press the Start/Pause button. to 40 degrees. • When in Pause, the power is turned off • It cannot be chosen in the Quick 30, automatically after 4 minutes. Hand Wash/Wool, Duvet, Delicat
Résumé du contenu de la page N° 18
ow to use washer H Child Lock Tub Clean If you choose to lock the buttons on the control Tub Clean course can be set by pressing assembly to prevent tampering this function and holding Intensive and Crease Care button simultaneously. may be selected. When Tub Clean course is set, the display will • Child Lock can be set by pressing the Medic show “ ”, and all other option buttons are Rinse button and Pre Wash button inoperable. simultaneously. (About three seconds) TUB CLEAN is special
Résumé du contenu de la page N° 19
ow to use washer H Spin • After selecting the wash course, the spin speed can be chosen by pressing the spin button. [WD13020D] [WD12020D] [WD11020D] 1. Spin selection 2. No spin • Spin Speed is available according to • If No spin is selected, the washer stops the program as follows. after draining the last rinse water. WD13020D 3. Rinse Hold - Cotton, Cotton Quick, Rinse+Spin, Quick 30, Bio Care, Bulky • Rinse Hold is selected by pressing the Rinse Hold - No Spin - 400 - 800 - 1300 spin button
Résumé du contenu de la page N° 20
ow to use washer H Water Temp. Time Delay • By pressing the Temp. button, the water temperature can be selected. - Cold Preparing washing before starting - 30˚C / 40˚C / 60˚C / 95˚C “Time Delay” - Turn on the water tap. - Load laundry and close the door. - Place Powdered only detergent and fabric • Water temperature can be selected softener in the appropriate compartments according to the program. of the dispenser drawer. The required temperature lamp will light up • How to set “Time Delay” for
