Résumé du contenu de la page N° 1
Installation/Maintenance
Washer-Extractor
Cabinet Freestanding
Model Numbers
BF35PV SF35PV UF35PV
BF50PV SF50PV UF50PV
BF85PV SF85PV UF85PV
NOTA: El manual en
español aparece después
del manual en inglés.
Part No. F232058R5
November 1999
Résumé du contenu de la page N° 2
Résumé du contenu de la page N° 3
Table of Contents Installation/Maintenance Water Connection ....................................................... 25 Safety Electrical Installation.................................................. 27 Key to Symbols .............................................................4 Steam Requirements (Steam Heat Operator Safety .............................................................5 Option Only)......................................................... 29 Safe Operating Environment..........
Résumé du contenu de la page N° 4
© Copyright 1999, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 2 F232058
Résumé du contenu de la page N° 5
Section 1 Safety Anyone operating or servicing this machine The following warnings are general examples must follow the safety rules in this manual. that apply to this machine. Warnings specific Particular attention must be paid to the to a particular installation or maintenance DANGER, WARNING, and CAUTION procedure will appear in the manual with the blocks which appear throughout the manual. discussion of that procedure. CAUTION DANGER Be careful around the open door, Death or serious inju
Résumé du contenu de la page N° 6
Safety CAUTION WARNING Ensure that the machine is installed on a Never touch internal or external steam level floor of sufficient strength and that the pipes, connections, or components. These recommended clearances for inspection surfaces can be extremely hot and will and maintenance are provided. Never allow cause severe burns. The steam must be the inspection and maintenance space to turned off and the pipe, connections, and be blocked. components allowed to cool before the pipe SW020 c
Résumé du contenu de la page N° 7
Safety To provide personal safety and keep the c. Close and lock the door and start a machine in proper working order, follow all cycle. Attempt to open the door while maintenance and safety procedures presented in the cycle is in progress. The door this manual. If questions regarding safety arise, should not open. contact the factory immediately. If the door lock and interlock are not functioning properly, call a Use factory-authorized spare parts to avoid service technician. safety hazar
Résumé du contenu de la page N° 8
Safety • Ventilation. The need for make-up air Safe Operating Environment openings for such laundry room accessories as dryers, ironers, water heaters, etc., must Safe operation requires an appropriate be evaluated periodically. Louvers, screens, operating environment for both the operator or other separating devices may reduce the and the machine. If questions regarding safety available air opening significantly. arise, contact the factory immediately. • Radio Frequency Emissions. A fil
Résumé du contenu de la page N° 9
Safety Machine Location • Steam Heat (Optional) Pressure. Best performance will be realized if steam is provided at a pressure of 30 – 80 psi • Foundation. The concrete floor must be of (2.0 – 5.4 bar). Steam pressure higher than sufficient strength and thickness to handle 125 psi (8.5 bar) may result in damage the floor loads generated by the high to steam components and may cause extract speeds of the machine. personal injury. • Service/Maintenance Space. Provide For machines equipp
Résumé du contenu de la page N° 10
Safety • A clean power supply free from voltage Safe Operating Environment spikes and surges is absolutely essential for (Continued) machines equipped with the AC inverter drive. Nonlinear inconsistencies (peaks and valleys) in the power supply can cause the AC inverter drive to generate WARNING nuisance errors. Ensure that a ground wire from a proven earth ground is connected to the ground lug If voltage is above 230V for 200V near the input power block on this machine. installations
Résumé du contenu de la page N° 11
Section 2 Installation This manual is designed as a guide to the The cylinder is supported by roller bearings installation and maintenance of the 35-pound, housed inside a trunnion. 50-pound, and 85-pound capacity freestanding washer-extractors. The cylinder is constructed with four lifters or ribs that lift the laundry from the bath solution The manuals, installation instructions, and when the cylinder rotates at slow speed and wiring diagrams which accompany the then allow it to tumble b
Résumé du contenu de la page N° 12
Installation Machine Overview (Continued) Customer Service If literature or replacement parts are required, The doorbox contains the Hall-effect door- contact the source from whom the machine closed sensor, door-open sensor, and the was purchased or contact Alliance Laundry door-unlock solenoid. Systems at (920) 748-3950 for the name of the nearest authorized parts distributor. Electromechanical valves control water flow into the washer-extractor. For technical assistance, call any of the
Résumé du contenu de la page N° 13
Installation Model Number Familiarization Guide Sample Model Number: UF50PVQU10001 UF Model Number Prefix 50 Machine Capacity (pounds dry weight) P Type of Electrical Control P = WE-6 Computer V Machine Speed Capabilities V = 7 Speeds Q Electrical Characteristics See Voltage Designation Chart in this section. U3 Design Series 0001 Option Identification (varies from machine to machine) UF50PVQU30001 00000000000 200-240 15 30 3 60 3 50 23 900 500000 G003I1A Figure 1 11 F232058
Résumé du contenu de la page N° 14
Installation 35-Pound, 50-Pound, and 85-Pound Models General Specifications 35 50 85 Overall Dimensions Overall width, in (mm) 35 (889) 39 (990) 46.5 (1181) Overall height, in (mm) 55.4 (1407) 59.6 (1514) 70.1 (1781) Overall depth, in (mm) 39 (992) 41.3 (1049) 50 (1270) Weight And Shipping Information Net weight, lb (kg) 1212 (550) 1600 (726) 3000 (1362) Domestic shipping weight, lb (kg) 1260 (572) 1650 (749) 3100 (1407) 3 3 Domestic shipping volume, ft (m ) 63.6 (1.80) 80 (2.26) 123 (3.46) Expo
Résumé du contenu de la page N° 15
Installation 35-Pound, 50-Pound, and 85-Pound Models General Specifications (Continued) 35 50 85 Cylinder Speeds Gentle wash/reverse speed, rpm 26 26 26 Wash/reverse speed, rpm 43 40 41 Distribution/drain speed, rpm 77 73 65 Medium extract speed, rpm 325 305 280 High extract speed l, rpm 475 445 410 High extract speed 2, rpm 610 575 525 High extract speed 3, rpm 960 900 825 Centrifugal Force Data Gentle wash/reverse centrifugal force, Gs 0.25 0.29 0.345 Wash/reverse centrifugal force, Gs 0.69 0.
Résumé du contenu de la page N° 16
Installation Machine Dimensions Note: The dimensions shown here are for planning purposes only. They are approximate See Figure 2 for dimensions of the 35-pound and subject to normal manufacturing capacity models. See Figure 3 for dimensions tolerances. If exact dimensions are required for of the 50-pound capacity models. See Figure 4 construction purposes, contact the distributor for dimensions of the 85-pound capacity or manufacturer. We reserve the right to make models. changes at a
Résumé du contenu de la page N° 17
Installation 32" (814 mm) 25 1/10" (638 mm) 22" (559 mm) 35" 39" (889 mm) (992 mm) Front Side 32 3/5" (828 mm) 32" (813 mm) 23 9/10" (606 mm) 49 2/5" 55 2/5" (1255 mm) (1408 mm) 52 1/10" (1323 mm) 40 3/5" (1031 mm) 11 4/5" (300 mm) 8 1/5" 11" (209 mm) (279 mm) Rear B145IE3B 35-Pound Capacity Models Figure 2 15 F232058
Résumé du contenu de la page N° 18
Installation 34 3/10" (872 mm) 26 1/5" (666 mm) 22 9/10" (582 mm) 41 3/10" 39" (1049 mm) (991 mm) Front Side 36 3/5" (930 mm) 35" (889 mm) 24 2/5" (619 mm) 59 3/5" (1513 mm) 55 1/10" 44 7/10" (1399 mm) (1136 mm) 11 4/5" (300 mm) 10 1/5" 10 1/5" (260 mm) (260 mm) B146IE3B 50-Pound Capacity Models Rear Figure 3 16 F232058
Résumé du contenu de la page N° 19
Installation 41 1/2" (1054 mm) 32 7/10" (831 mm) 30 1/10" (765 mm) 46 1/2" 50" (1181 mm) (1270 mm) Front Side 43 3/5" (1107 mm) 42 3/5" (1083 mm) 29 9/10" (758 mm) 25 2/5" (645 mm) 70 1/10" (1781 mm) 51 3/5" (1311 mm) 66 2/5" 50 3/5" (1685 mm) (1284 mm) 11 1/10" (281 mm) 7 3/4" 10" (197 mm) (254 mm) 85-Pound Capacity Models Rear U091IB Figure 4 17 F232058
Résumé du contenu de la page N° 20
Installation The washer-extractor must be placed on a Machine Foundation smooth level surface so that the entire base of the machine is supported and rests on the Thoroughness of detail must be stressed mounting surface. (Do not support the washer- with all foundation work to ensure a stable extractor on only four points.) unit installation, eliminating possibilities of excessive vibration during extract. The 35-pound, 50-pound, and 85-pound capacity washer-extractors do not require CAUT
