Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
Table of Contents TABLE OF CONTENTS.............................................................................................. 2 SAFETY PRECAUTIONS ........................................................................................... 3 SPECIFICATIONS ...................................................................................................... 4 Heating Specifications..................................................................................... 4 Dimensions ..............
Résumé du contenu de la page N° 3
Safety Precautions IMPORTANT: Read this entire manual before installing Disconnect the power cord before performing any and operating this product. Failure to do so may result maintenance! NOTE: Turning the ON/OFF Switch to in property damage, bodily injury, or even death. ”OFF” does not disconnect all power to the electrical Proper installation of this furnace is crucial for safe components of the furnace. and efficient operation. Never try to repair or replace any part of the furna
Résumé du contenu de la page N° 4
Résumé du contenu de la page N° 5
Fuel Considerations SHELLED CORN (Dry, preferably corn with 11% or less moisture content) • Optimum moisture content of corn should be 11% or less. Wet corn will rapidly deteriorate furnace components, reduce efficiency and void all warranties. Purchase a moisture tester if in doubt. • Corn must be clean and free from debris. Never burn corn right from the field. Damage caused by dirty corn is not covered by the product warranty. Ask for clean filtered bagged corn only. Stalk parts, excessi
Résumé du contenu de la page N° 6
Résumé du contenu de la page N° 7
Résumé du contenu de la page N° 8
Installation VENTING REQUIREMENTS Install vent at clearances specified by the vent manufacturer. Do not connect the pellet vent to a vent serving any other appliance or furnace. Do not install a flue damper in the exhaust venting system of this unit. The following installation guidelines must be followed to ensure conformity with both the safety listing of this furnace and to local building codes. IMPORTANT! This unit is equipped with a negative draft system that pulls air through the
Résumé du contenu de la page N° 9
Installation VENT TERMINATION CLEARANCES: A ----- Minimum 4-foot clearance below or beside any door or window that opens. B ----- Minimum 1-foot clearance above any door or window that opens. C ----- Minimum 3-foot clearance from any adjacent building. D ----- Minimum 7-foot clearance from any grade when adjacent to public walkways. E ----- Minimum 2-foot clearance above any grass, plants, or other combustible materials. F ----- Minimum 3-foot clearance from a forced air intake of any appliance.
Résumé du contenu de la page N° 10
Installation THROUGH THE WALL INSTALLATION (RECOMMENDED INSTALLATION) To vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter. If the exhaust adapter is at least 18-inches above ground level, a straight section of pellet vent pipe can be used through the wall. Your furnace dealer should be able to provide you with a kit that will handle most of this installation, which will include a wall thimble that will allow the proper clearance through a combustible wall. On
Résumé du contenu de la page N° 11
Installation PRIMARY FURNACE SECONDARY (ADD-ON) FURNACE When installed as a seondary furnace, a Duct Damper must be installed between the air discharge of the 6300 furnace and the primary (Gas, Electric, etc.). This duct damper prevents the air from the primary furnace from back flowing to the secondary furnace. Damper must be a mechanical (spring return) style with a simple closure switch to determine if the damper is opened or closed. The damper will connect to the multi-fuel furnace’s prin
Résumé du contenu de la page N° 12
Résumé du contenu de la page N° 13
Résumé du contenu de la page N° 14
LIGHTING INSTRUCTIONS CAUTION: DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. Before lighting your heater for the first time, make sure that all items are out of the hopper, ash pan and firebox area. Press the “On” button and allow your heater to run for at least 4 minutes, to check for proper operation. Once your heater is started, you will notice the draft fan starts immediately. If you press
Résumé du contenu de la page N° 15
Operation DAILY OPERATION The hopper and furnace top will be hot during operation; therefore, you should always use some type of hand protection when refueling your furnace. Never place your hand near the auger while the furnace is in operation. In the event of a power outage, the furnace WILL NOT function. It is very important that unit be vented properly, as the natural draft is needed to clear the smoke from the furnace during a power outage. If the unit was “ON” when the power outage
Résumé du contenu de la page N° 16
Maintenance INTERIOR CHAMBERS Open the Ash Cleanouts and scrap all ash into the ash pan. Open the damper and allow the ashes to fall into the ash pan. The damper may need to be slide in and out several times to clear any ash build-up. This may need to be done daily depending on fuel consumption. Be sure the ash cleanouts located on either side of the damper are completely closed before operating. Periodically remove and clean the burnpot and the area inside the burnpot housing. In particula
Résumé du contenu de la page N° 17
Résumé du contenu de la page N° 18
Parts List Item Part No. Title Qty. Item Part No. Title Qty. 1 891481 Top Cover Weldment 1 36 80495 120 CFM Draft Fan 1 2 891471 Lid Weldment 1 37 88123 Gasket, Blower 120 CFM 1 3 891375 Side Panel, Right 1 38 891491 Transition, Exhaust Blower 1 4 891376 Weld., Left Side Panel 1 39 80531 RTD, Platinum 1 5 891438 Access Panel, Back 1 40 891269 Assy, Auger Housing 1 6 80502 Assembly, Circuit Board 1 41 891141 Auger 1 7 69524 Assembly, Feed Door 1 42 891248 Weldment, Bottom Plate Retainer 1 8 83508
Résumé du contenu de la page N° 19
Résumé du contenu de la page N° 20
Trouble Shooting Disconnect the power cord before performing any maintenance! NOTE: Turning the ON/OFF Switch to ”OFF” does not disconnect all power to the electrical components of the furnace. Never try to repair or replace any part of the furnace unless instructions for doing so are given in this manual. All other work should be done by a trained technician. PROBLEM CAUSE: Too rich air/fuel mixture Orange, lazy flame_excessive fuel • Clean out the burnpot and burnpot housing buil
