Résumé du contenu de la page N° 1
DESIGNER/LUXURY BATH SERIES
INSTALLATION / OPERATION INSTRUCTIONS
Save These Instructions for Future Use.
Complete and mail-in the product registration card provided with your unit.
Write and save the model and serial number of your unit below.
Owner's Record
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Num
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: DANGER: — TO REDUCE THE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS UNIT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES. WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO NOT USE ATTACHMENTS
Résumé du contenu de la page N° 3
ENGLISH INSTALLATION INSTRUCTIONS WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: DANGER — RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI). CAUTION — TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODICALLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS. WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO NOT USE ATTACHMENTS NOT RE
Résumé du contenu de la page N° 4
CONTENTS Safety Instructions _____________________________________________________________________ 2-3 Contents _____________________________________________________________________________ 4 Specifications _________________________________________________________________________ 5-8 Roughing-in Reference _________________________________________________________________ 9-13 Installations Instructions _________________________________________________________________ 14-19 Framing and Support ___
Résumé du contenu de la page N° 5
ENGLISH SPECIFICATIONS Important: Read complete instructions before beginning installation. Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly, heater, plumb- ing, and fittings necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath. Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any
Résumé du contenu de la page N° 6
SPECIFICATIONS SPECIFICATIONS (Rectangular) LH = Left Hand, RH = Right Hand HEATER, TOTAL WEIGHT/ OPERATING PRODUCT SKIRT & INTAKE/DISCHARGE DIMENSIONS DRAIN/OVERFLOW CUTOUT FLOOR LOADING GALLONAGE WEIGHT MOUNTING MODEL ALLUSION™ 66" (1676 mm) L 17-3/8" (441 mm) A Template 843 lb Min - 55 U.S. gal 135 lb Not Available Factory Installed 6636 36" ( 914 mm) W 11-15/16" (210 mm) B Provided (383 kg)/ (208 liters) (61 kg) Intake 2 26" ( 660 mm) H P/N 51 lb/ft Max - 75 U.S. gal (S749000 Heater) 2 RH
Résumé du contenu de la page N° 7
ENGLISH SPECIFICATIONS OVAL & ROUND BATHS A MAX. 2-1/2" L W 1/2" H B (Heater) (13 mm) DRAIN/OVERFLOW (Motor) SIDE VIEW END VIEW DUETTA™ (51 mm) L (Heater) 2" MAX. 1/2" L W W H (Heater) (Motor) (Motor) SIDE VIEW END VIEW CORTINA™ VENICIA™ SPECIFICATIONS (Oval & Round) LH = Left Hand, RH = Right Hand PRODUCT SKIRT & DRAIN/OVERFLOW TOTAL WEIGHT/ OPERATING HEATER, WEIGHT MODEL DIMENSIONS CUTOUT FLOOR LOADING MOUNTING INTAKE/DISCHARGE DIMENSIONS GALLONAGE CORTINA™ 72" (1829 mm) L 1293 lb 100
Résumé du contenu de la page N° 8
SPECIFICATIONS CORNER BATHS MAX. 1/2" W 2" A H (51 mm) (Heater) B SIDE VIEW END VIEW DRAIN/OVERFLOW BELLAVISTA™ CORNER, Right Hand SPECIFICATIONS (Corner) LH = Left Hand, RH = Right Hand DRAIN/OVERFLOW TOTAL WEIGHT/ OPERATING PRODUCT SKIRT & HEATER, CUTOUT FLOOR LOADING GALLONAGE WEIGHT MOUNTING INTAKE/DISCHARGE MODEL DIMENSIONS DIMENSIONS TM Factory Installed BELLAVISTA 60" (1524 mm) L 18-7/8" (479 mm) A Template 1046 lb 80 U.S. gal 130 lb Not Available Intake CORNER 60" (1524 mm) W 14" (356
Résumé du contenu de la page N° 9
ENGLISH ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (RECTANGULAR) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. 66" 72" Motor Motor 5" x 5" 5" x 5" 8-1/2" 36" 8-1/2" 36" Heater Heater 11-15/16" 11-15/16" Opt. Service Opt. Service 33" 36" Access Access ALLUSION™ 6636, Right Hand ALLUSION™ 7236, Right Hand 72" 12" H x 18" L Service Access 60" Motor 5" x 5" Motor 8-1/2" 30-1/8" 42" 4" x 4" Heater 42" Heater 11-15/16
Résumé du contenu de la page N° 10
ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (RECTANGULAR) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. 60" 60" 21" 21" 12" x 4" 12" x 4" Motor Motor 42" 42" 2" 2" Heater Heater 4.2" 4.2" Opt. Service Opt. Service 12" H x 18" L 12" H x 18" L 10.6" 10.6" Access Access Service Access Service Access ELARA™ 6042 Left Hand ELARA™ 6042 Right Hand 66" 66" 18 " 18 " 12" x 4" 12" x 4" Motor Motor 36" 36" Heater 2" Heater 2" 4.2"
Résumé du contenu de la page N° 11
ENGLISH ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (RECTANGULAR) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. 1" 1" 72" 72" Motor 3" 42" Motor 18" x 4" 18" x 4"* 47" 3" Heater 3" 3" 7" Opt. Service 10-1/2" 5-1/4" Access 36" Heater 10-1/4" 36" Opt. Service Access REÁL™, Right Hand SABELLA™ Right Hand 72" Motor 18" 15" X 4" 36" Heater 6-3/4" Opt. Service Access 15-1/4" TORRETTA™ 36, Left Hand * Add 1/4" to
Résumé du contenu de la page N° 12
ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (OVAL) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. 66" 60" Motor Motor 13" x 4" 13" x 4" 2" 36" 2" 42" Heater Heater Opt. Service 3.84" Opt. Service Access 3.84" Access 11.04" 11.04" 33" 30" DUETTA™ 6042, Right Hand DUETTA™ 6636, Right Hand 66" 12" H x 18" L 72" Service Access Motor 42" 14" x 4" Motor 13" x 4" 2" Heater 42" Heater 3-1/2" 11" Opt. Service 3.84" Access 2" Opt
Résumé du contenu de la page N° 13
ENGLISH ROUGHING-IN REFERENCE ROUGHING-IN REFERENCE (ROUND, CORNER) Some tubs are supplied with cutout and/or undermount template. Refer to CUTOUT on pages 6-8 for template part numbers. 60" Service 14"x5"* 60" Access 59-1/2" 72" 5" Ref. 34-9/16" Heater 16" 26" Motor 12"x4" Heater Opt. Service 16" Access 12" H x 18" L Motor Service Access 3" 4" 7-1/2" 9" 77-3/4" 72" BELLAVISTA™ CORNER, Right Hand CORTINA™, Right Hand NOTE: 1. Measurements inside each unit represent cutout in floor
Résumé du contenu de la page N° 14
INSTALLATION INSTRUCTIONS Framing and Support The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer to the table under total weight for your model. The unit must be supported from the bottom of the bath and not from the bath rim or tile flange. If the subfloor is level and a continuous surface, no other preparation is neces
Résumé du contenu de la page N° 15
ENGLISH INSTALLATION INSTRUCTIONS The Duetta Whirlpool baths should access as shown Service Access below. For partially or fully sunken installations, allow for ac- DUETTA SERVICE ACCESS (WITHOUT SKIRT) cess to service connections. It is the installer's respon- sibility to provide sufficient service access. The recom- mended minimum dimensions allowable for service to the bath are shown in the "Service Access" illustration. Provide adequate area around unit for air circulation for cooling the
Résumé du contenu de la page N° 16
INSTALLATION INSTRUCTIONS INSTALLATION CLEARANCE RECOMMENDATIONS The installation clearance recommendations below are to ensure that installers have enough space to maneuver and insert tub. The Designer/Luxury line whirlpool tubs have electrical, plumbing and lighting systems installed. Do not lift the bath by the plumbing or wiring at any time; handle by the shell only. TWO WALL INSTALLATION TUB CUTOUT TUB CUTOUT 10" 32" THREE WALL INSTALLATION MINIMUM VERTICAL CLEARANCE FOR INS
Résumé du contenu de la page N° 17
ENGLISH INSTALLATION INSTRUCTIONS Installation See END/SIDE VIEW in Specification pages for Note that the motor/pump protrudes beyond the bath rim a maxi- this dimension. mum distance of 1" (25,4 mm). Care should be used when lowering the tub into cutout to prevent injury to installer(s), finished surfaces, (Heater) or tub and components. (Motor) Clearance must be provided for installers. See page 16 for recommended clearances surrounding tub. Damage to shell, plumbing, wiring, lighting, and
Résumé du contenu de la page N° 18
INSTALLATION INSTRUCTIONS Electrical Connections Separate circuits, each must be protected by a Ground Fault Circuit Interrupter (GFCI), are required for the pump/ TM motor and the RapidHeat Heater. Refer to the electrical specification for each model on pages 6-8. Install duplex outlets to the studwall underneath the bathtub, at least 4 inches (10,2 cm) above the floor or in accordance with local building or electrical codes. Duplex outlets are not provided. Because these units are manufact
Résumé du contenu de la page N° 19
ENGLISH Plumbing and Water Supply Drain Information Water Supply A drain/overflow assembly (sold separately) must be in- Consult local authorities for plumbing code requirements stalled on the bath, water tested, and connected to the sani- in your area. tary system of the house. After opening the carton, inspect IMPORTANT: Proper installation of the fill spout plumb- for damage and verify that the kit is of the proper finish. In the ing and compliance with local codes are the responsibil- Jac
Résumé du contenu de la page N° 20
1" - 2" OPERATING INSTRUCTIONS OPERATION NOTE: These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath. Not all features dis- cussed in this instruction pamphlet apply to all baths. All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold water continuously like pools
