Résumé du contenu de la page N° 1
COMFORT PLUS BATH SERIES
INSTALLATION AND OPERATING INSTRUCTIONS
Installer: Leave this manual for homeowner.
Homeowner: Read this manual and keep for future reference.
©
Jacuzzi Whirlpool Bath BP43000 2/05
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION: TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODI- CALLY IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS. WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT ADULT SUPERVISION. WARNING: TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE BATHTUB WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT
Résumé du contenu de la page N° 3
ENGLISH PRECAUTIONS • Do not operate the whirlpool system unless the bath is filled with water to at least 1" (25 mm) above the highest jet. • Never drop or insert any object into any opening. • Do not use oil-based bath additives in your whirlpool bath. • When cleaning your bath, do not use abrasive substances which will damage the bath's surface. • To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140° F (60° C) • The whirlpool system should be purged
Résumé du contenu de la page N° 4
ADDENDUM Safety Instructions Change IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: DANGER: TO REDUCE THE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS UNIT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES. WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN T
Résumé du contenu de la page N° 5
INSTALLATION INSTRUCTIONS WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: DANGER — RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI). CAUTION — TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODICALLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS. WARNING — USE THIS UNIT ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL. DO NOT USE ATTACHMENTS NOT RECOMMEND
Résumé du contenu de la page N° 6
CONTENTS Specifications _________________________________________________________________________ 1-2 Roughing-in Reference _________________________________________________________________ 3 Installation Instructions __________________________________________________________________ 4-8 Framing and Support _________________________________________________________________ 4 Skirts ______________________________________________________________________________ 5 Service Access ____________________
Résumé du contenu de la page N° 7
ENGLISH SPECIFICATIONS Important: Read complete instructions before beginning installation. Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath. Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any time; h
Résumé du contenu de la page N° 8
RIMLESS OVAL BATHS L W 2" (51 mm) A (Heater) H (Motor) B SIDE VIEW END VIEW DRAIN/OVERFLOW LUNA PLUS SPECIFICATIONS (Oval) PRODUCT SKIRT & DRAIN/OVERFLOW TOTAL WEIGHT/ OPERATING HEATER MOUNTING DIMENSIONS DIMENSIONS FLOOR LOADING WEIGHT MODEL CUTOUT GALLONAGE LUNA™ PLUS 72" (1829 mm) L 19-1/8" (486 mm) A Template 1176 lb 96 U.S. gal 126 lb Not Factory Installed 42" (1118 mm) W 11" (279 mm) B Provided (535 kg)/ (364 liters) (57 kg) Available (S750000 HEATER KIT) 2 23" ( 584 mm) H P/N 56 lb/ft 2
Résumé du contenu de la page N° 9
ENGLISH ROUGHING-IN REFERENCE (RECTANGULAR) Note: 1. Baths shown are left-hand unless otherwise specified. Right-hand is a mirror image. 2. Some units have been provided with cutout templates included in shipping carton. See CUTOUT information for each model on page 1 and 2. 3. THE OVERALL DIMENSIONS ARE NOMINAL WITH A TOLERANCE OF +0 AND -1/4". 4. Measurements inside each unit represent cutout in floor to allow for drain/overflow. 5. All measurements are in inches. To convert to millimet
Résumé du contenu de la page N° 10
Framing and Support The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer to the table under total weight for your model. The unit must be supported from the bottom of the bath and not from the bath rim or tile flange. If the subfloor is level and a continuous surface, no other preparation is necessary. You can proceed to
Résumé du contenu de la page N° 11
ENGLISH Skirts U FRAME SKIRT MOUNTING DETAIL INTEGRAL SKIRT MOUNTING DETAIL FINISHING MATERIALS FINISHING SECURE SHELL CLIP MATERIALS UNDER CENTER BATH RIM CAULKING BEAD FILLER (Optional) CAULKING BEAD SKIRT SKIRT PANEL PANEL SKIRT FRAME SECURE BOTTOM OF FRAME TO FLOOR Removable Skirt Panel To remove panel, grab the top of access panel and pull outward to release Velcro™. Then pull access panel upward to release holding clips. To reinstall, engage holding clips onto skirt and then push panel fo
Résumé du contenu de la page N° 12
Service Access Service Access with Skirt For partially or fully sunken installations, allow for access to ser- An optional skirt fits along the side of the bath for above-floor vice connections. It is the installer's responsibility to provide suffi- installations and is also an access panel for servicing. Allow a space cient service access. The recommended minimum dimensions al- of at least 8 inches away from the bath for skirt removal. lowable for service to the bath are shown in the "Servic
Résumé du contenu de la page N° 13
ENGLISH Electrical Connections Two separate 120 VAC, 15 AMP circuits, which must be protected by a Ground Fault Circuit Interrupter (GFCI), are required. Install duplex outlets to the studwall underneath the bathtub, at least 4 inches above the floor. The duplex outlets are not provided. One circuit is for the TM pump/motor and the other is for the RapidHeat heater. Install a separate 120 VAC, 15 AMP dedicated circuit with GFCI protection. With a #8 solid copper wire, bond the heater to the h
Résumé du contenu de la page N° 14
Plumbing and Water Supply Drain Information A drain/overflow assembly (sold separately) must be installed on the bath, water tested, and connected to the sanitary system of the house. © After opening the carton, inspect for damage and verify that the kit is of the proper finish. In the Jacuzzi Whirlpool Bath drain/overflow kit, note that the waste flange, strainer, overflow cover and cover screws are packaged in a separate package within the kit to protect the trim finish. Follow the installati
Résumé du contenu de la page N° 15
ENGLISH 1" OPERATING INSTRUCTIONS LED DISPLAY Operation Note: These instructions pertain to all bath products manufac- tured by Jacuzzi Whirlpool Bath. Not all features discussed in this instruction pamphlet apply to all baths. 1101 01 © All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold wat
Résumé du contenu de la page N° 16
TYPICAL BATH FITTINGS Controlling Whirlpool Action The whirlpool action in your bath is influenced by three factors – COMFORT PLUS direction of flow, force of water, and force of air. All whirlpool baths ON/OFF SWITCH © manufactured by Jacuzzi Whirlpool Bath are equipped with adjust- AIR CONTROL ® able PowerPro jets, that may be adjustable for one or more of the KNOBS three factors. Direction: To change the direction of the water flow, swivel the jet nozzle to the desired angle. The jets can
Résumé du contenu de la page N° 17
ENGLISH MAINTENANCE INSTRUCTIONS Cleaning the Bath Suction Cover/Strainer Maintenance To clean your bath, simply use a mild, nonabrasive liquid deter- Clean the suction cover/strainer of hair and debris when neces- gent solution. You can protect and restore the gloss to a dulled sary. To do this, remove the center screw and detach the square acrylic surface by applying an acrylic polish or automotive paste wax. cover. Clean the cover by backflushing debris from the holes. Re- Never use abras
Résumé du contenu de la page N° 18
General Whirlpool Bath Troubleshooting Guide PROBLEM PROBABLE CAUSES REMEDY Pump/Motor does not start. No power to pump/motor. Reset GFCI. Pump/motor not plugged in. Insert plug fully into outlet. Magic Touch switch - air tube not Reconnect tube to Magic Touch switch connected to switch or to air switch or to air switch pump/motor. on pump/motor. Pump/motor faulty. Replace pump/motor assembly. Pump/Motor operates but no fully Jets are closed. Open jets by rotating counterclockwise. adjustab
Résumé du contenu de la page N° 19
ENGLISH PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. © Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. © Jacuzzi Whirlpool Bath makes no representation or warranty regarding, and will not be responsible for a
Résumé du contenu de la page N° 20
Authorized Service If you need a referral for a service company near you, or need assistance with operation or maintenance related questions, please call our Service Support Department at 1-800-288-4002. For service agent listing, visit our web site at http://www.jacuzzi.com/. To find the service agent listings, click on For The Trade. Then click on Electrical/ Mechanical Service Agents. Depending on the problem, click on Electrical/Mechanical Repairs or Finish, Surface or Shell-Related Probl
