Instruction d'utilisation FrancisFrancis FX560

Instruction d'utilisation pour le dispositif FrancisFrancis FX560

Dispositif: FrancisFrancis FX560
Catégorie: Eclairage aquatique
Fabricant: FrancisFrancis
Dimension: 1.72 MB
Date d'addition: 10/4/2014
Nombre des pages: 30
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif FrancisFrancis FX560. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec FrancisFrancis FX560.

Pour votre confort

Si regarder l'instruction FrancisFrancis FX560 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction FrancisFrancis FX560 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction FrancisFrancis FX560 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
FrancisFrancis FX560 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 30 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction FrancisFrancis FX560 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de FrancisFrancis FX560. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

User Instruction & Installation Manual
FX560 Remote Control
2 Kilowatt Xenon Searchlight
Product Reference Number:
A2471 – Variable Speed Motor Unit 240v
A2473 – Variable Speed Motor Unit 115v
Manufacturers details: Distributor details:
Francis Searchlights Ltd
Union Road, Bolton
Lancashire, BL2 2HJ, UK
Tel: +44 (0) 1204 558960
Fax: +44 (0) 1204 558979
http://www.francis.co.uk
E-mail: sales@francis.co.uk
Manual Part Number: C20244
Issue : 10

Résumé du contenu de la page N° 2

CONTENTS 1 - Introduction 2 - Safety Precautions 3 - Technical Information 4 - Unpacking and Installation Instructions 5 - Electrical Installation 6 - Operating Instructions 7 - Fault Finding 8 - Maintenance and Servicing 9 - General Assembly & Wiring Diagrams 10 - Spare Parts List

Résumé du contenu de la page N° 3

1 - Introduction It is imperative that this manual is read carefully and understood before installing your equipment. For your future reference please keep this manual in a safe place. Thank you for specifying a product from the Francis Searchlights range. All Francis products are designed to give complete customer satisfaction and are manufactured to the highest engineering standards in order to ensure optimum performance and service life. The Francis Xenon range combine features proven over ma

Résumé du contenu de la page N° 4

2 - Safety Precautions The following instructions must be adhered to, in order to ensure a safe working environment and the safety of the user. Note: When unpacking or manoeuvring the searchlight into its fixing position, suitable lifting points must be used in order to prevent damage to the equipment or personal injury. Because of the high internal pressure within the lamp, there is a risk of explosion in either a hot or cold state; During operation this lamp emits intense UV radiation which

Résumé du contenu de la page N° 5

3 - Technical Information This product has been designed to operate in accordance with the product specification. The FX560RC 2000 watt searchlight has the following features: All marine grade materials and fixings; Electronic power supply unit; Parabolic glass reflector; Stove enamel painted; 385° horizontal rotation; Vertical movement 20° to -20°; Motor speed 0-20°/sec fast, 0-10°/sec slow (Pan) 0-10°/sec fast, 0-5°/sec slow (Tilt); Remote focus facility; Internal self-regulating heat

Résumé du contenu de la page N° 6

Power Supply Details (Model 8502) General Description Output Power 1400-2200 watts Voltage 22-30 volts D.C. Current 50-85 amperes D.C. Ripple 5% peak-to-peak Input Current 25/22 amperes maximum 40 amperes maximum Voltage 208/237 VAC 110/120 VAC Phase Single Frequency 60 Hz (50Hz available) Output Adjustments 9 steps Size Width 12” (30.5 cm) Height 15” (38 cm) Length 19” (48.25 cm) Weight 145 lbs. (65.9 Kg) Cooling Convection Warning When this appears in this text, it indicates a hazard to person

Résumé du contenu de la page N° 7

Caution Do not allow anything to be placed upon the power supply case; the perforated top is for ventilation and must not be obstructed. Try to select a location as close to the lamphouse as practical. Many users install the power supply adjacent to the searchlight where space is available and local codes permit. Electrical installation and connection Caution Much future grief can be avoided by having a competent electrical contractor install and connect this unit. Caution We make suggestions in

Résumé du contenu de la page N° 8

Warning The power supplies have two sources of power. Disconnect (turn off) primary power before making adjustments or service procedures. Output power adjustment Warning The power supply stores energy after primary power is switched off. Wait a minimum of two minutes for the capacitor charge to bleed off. Taps are provided on TB1 to alter the output of the power supply. Small current changes may be made by moving the tap from H to M to L. Highest current is on H; the lowest is on L. Larger curr

Résumé du contenu de la page N° 9

Xenon lamp power supplies have two stages of operation: 1) Before igniting the bulb – At this time, the voltage at the power supply output terminals reaches “open circuit” value (110 VDC or greater). 2) After igniting the bulb – At this time, the voltage at the power supply output is determined by the load placed on the power supply by the xenon lamp (18-30 VDC). Power supply difficulties can be separated into one of three areas for purposes of diagnosis and repair: A) Power line problems. B) Bo

Résumé du contenu de la page N° 10

Low capacity or an open capacitor affect ignition because there is insufficient surge current to reliably light the bulb. If disconnecting a capacitor does change either flicker or ignition, then the capacitor is functioning. Reconnect it. High ripple current caused by a diode failure will result in overheating of R3. You may use a clamp-on A.C. ammeter on the common D.C. line to the capacitor bank as an indirect method of checking ripple. The 8502 capacitor bank will have a nominal 25 ampere (A

Résumé du contenu de la page N° 11

Back To Top

Résumé du contenu de la page N° 12

4 - Unpacking and Installation Instructions The following instructions should be read and fully understood prior to installing the equipment to ensure that the correct procedures are followed and all safety precautions are observed. Note: If the equipment has been in storage for a considerable amount of time, it is advisable to conduct a routine maintenance check on all parts before installation. Safety Precautions This equipment should not be connected to an electrical supply before being insta

Résumé du contenu de la page N° 13

5 - Electrical Installation For safety purposes, only competent personnel should perform the electrical installation. All equipment should be installed to current Electrical Regulations and Standards. In order to obtain the maximum light output from the searchlight, it is essential that the full operating voltage of the lamp fitted be applied to the lampholder contacts. Method of Electrical Connection 1) Disconnect the supply before working on the electrical system; 2) The searchlight must be

Résumé du contenu de la page N° 14

Installation Guidelines A typical installation and connection routine for the searchlight with a Variable Speed Gearbox is as follows: Referring to wiring diagram C22801, a supply is fed to the Control Panel, which then provides a common feed to the Motor Gearbox, Power Supply Unit and the Searchlight Control Panel. The searchlight has been pre-wired with 3 meters of cable from the gearbox to junction box provided. Cables required to be connected by the customer: - 4 core 6mm cable from the Ju

Résumé du contenu de la page N° 15

Fitting instructions for the 2Kw xenon lamp Referring to the diagram overleaf: 1) Unfasten the ten latches (A) on the front and rear of the searchlight; 2) Remove the front bezel (B) and rear bezel (C) assemblies; 3) Unscrew the two M6 hexagon screws (D) from the front lampholder mounting block (E) and remove the front lampholder assembly from the mounting bracket; 4) Loosen the knurled screw on the front (F)and rear (G) lampholder assembles; 5) The lamp can now be inserted, make sure that the n

Résumé du contenu de la page N° 16

Back To Top

Résumé du contenu de la page N° 17

6 - Operating Instructions This equipment is designed for use out of doors, in free air. Never place anything on, or cover, the searchlight when in use as this may present a hazard. All PSU should be housed below deck/in doors. Never leave the PSU exposed to weather conditions. The searchlight can be remotely positioned via the joystick control panel, with the facility for movement up, down, left and right. The speed of movement depends on the more pressure applied to the joystick the faster the

Résumé du contenu de la page N° 18

Setting to Work Safe service in use necessitates the strict observance of the following precautions. Any article fabricated from quartz or glass is inherently fragile and care should therefore be taken, at all times, when handling lamps; Eye protection must be worn when handling lamps that have been removed from their packaging materials. The protective jacket should not be removed from the lamp for safety reasons, as there is a remote possibility of the lamp shattering violently, especially i

Résumé du contenu de la page N° 19

Notes: 1) XBO lamps are designed for dc operation only. The dc current may only be varied within the limits of the current control range. An XBO lamp operates best at rated current; over the life of the lamp, the current may be increased to its maximum value to compensate for loss of light. The output of the lamp can be reduced by operating the lamp at minimum current but this does not prolong the life of the lamp; 2) For safety reasons, XBO lamps should be replaced once they reach the end of

Résumé du contenu de la page N° 20

7- Fault Finding All fault finding must be conducted by a competent person or qualified Electrical Engineer. Please refer to the following table for the trouble-shooting of Xenon lamps. Fault Cause Remedy Wrong Polarity Lamp incorrectly fitted Anode (large electrode) Faulty wiring must always be on top in vertical burning position Check polarity, transpose connections if necessary Cap overheated Faulty contacts Check terminals, tighten or Ca


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 FrancisFrancis !FR380 Manuel d'utilisation Eclairage aquatique 1
2 FrancisFrancis !A2541 Manuel d'utilisation Eclairage aquatique 0
3 ACR Electronics SM-2 Manuel d'utilisation Eclairage aquatique 0
4 ACR Electronics 1933 Manuel d'utilisation Eclairage aquatique 0
5 ACR Electronics MS-2000(M) Manuel d'utilisation Eclairage aquatique 3
6 ACR Electronics 3940.1 Manuel d'utilisation Eclairage aquatique 1
7 ACR Electronics RCL-300A Manuel d'utilisation Eclairage aquatique 1
8 Allmand 6330 Manuel d'utilisation Eclairage aquatique 0
9 Attwood 3500 Series Manuel d'utilisation Eclairage aquatique 0
10 Attwood 3540 Manuel d'utilisation Eclairage aquatique 0
11 Attwood 3120 Manuel d'utilisation Eclairage aquatique 0
12 Attwood 3134 Manuel d'utilisation Eclairage aquatique 0
13 Attwood 3530 Manuel d'utilisation Eclairage aquatique 0
14 Attwood 3104 Manuel d'utilisation Eclairage aquatique 0
15 Attwood 3560 Manuel d'utilisation Eclairage aquatique 0