Instruction d'utilisation ACR Electronics Y1-03-0165

Résumé du contenu de la page N° 1

Résumé du contenu de la page N° 2

IF YOU HAVE ANY TROUBLE WITH YOUR NEW LIGHT, DO NOT RETURN IT TO THE STORE! CALL ACR ELECTRONICS AT +1 (954) 981-3333. WE WILL HELP YOU RESOLVE ANY PROBLEMS YOU MAY BE EXPERIENCING. MANY QUESTIONS CAN BE ANSWERED OVER THE PHONE. LIMITED WARRANTY This product is warranted against factory defect in material and workmanship for a period of one year from date of purchase or receipt as a gift. During the warranty period ACR Electronics,

Résumé du contenu de la page N° 3

TABLE OF CONTENTS SECTION 1 - INSTALLATION .............................................................................................................. 4 1.1 Installation Procedures ........................................................................................................................................ 4 1.2 Battery Installation .............................................................................................................................................

Résumé du contenu de la page N° 4

FOREWORD We design, manufacture and distribute quality products knowing they are used to save lives. Many of our products are required to be tested and approved by regulatory bodies worldwide. We believe in going beyond those specifications to insure our products work when needed in real world conditions. With proper care and maintenance your ACR product will last for years. It is important that you thoroughly read this product support manual to understand the proper care and use of your

Résumé du contenu de la page N° 5

2.3 Disassembly This will ordinarily be required only if testing shows that the light is malfunctioning, or if battery replacement is required. Recommended interval for battery replacement is one year. A. Hold the unit on a flat, firm surface, lens side up. Depress the top cap of the unit, by pushing straight down on the top cap assembly, until the swivel locks may be turned outward, clear of the cap. B. Grip the light lens (using a clean cloth or gloves for a better grip on the smooth

Résumé du contenu de la page N° 6

2.5 SM-2 Parts List NOTE: Item numbers refer to Figure 1 on next page. ITEM DESCRIPTION PART NUMBER 1 Case Assembly A3-06-2295 *2 Case (not shown) A1-18-1878 *3 Washer, 3 each (not shown) A1-05-0659-3 *4 Locking Swivel, 3 each (not shown) A1-17-1283 5 Battery Pad, Foam A1-18-0773 6 Battery, 6 Volt Lantern Type (see page 4 for recommended batteries) Not Included (not shown) 7 Foam Filler A1-18-1877 8 O-Ring (Top Cap) A1-05-0001-64 9 Top Cap and Lens Tube Assembly 9021.1 10 Mounti

Résumé du contenu de la page N° 7

FIGURE 1 EXPLODED VIEW SM-2 7 Y1-03-0165 Rev. D

Résumé du contenu de la page N° 8

SECTION 3 - CHARACTERISTICS 3.1 General This section describes operating instructions and operational characteristics of the SM-2 Automatic Crew-Overboard Light. The information presented is in conformance with U.S. Coast Guard Specification 46 CFR 161.010 and 161.110. The SM-2 is a lightweight, compact, battery operated, portable unit which uses modular construction for basic circuits to simplify maintenance and replacement procedures. The SM-2 has been designed and tested to pass t

Résumé du contenu de la page N° 9

3.9 Stroboscopic Flashing Light The SM-2 Flashing Light uses a capacitor discharge xenon flashtube and meets the following requirements: A. A completely sealed solid state circuit converts power from the battery and supplies it to the flashtube. B. A suitable capacitor discharge xenon flashtube is provided which is compatible with the electronic flashing circuit and lens to provide the required light output. The service life of this flashtube is rated for over 1,000,000 flashes. C. Th

Résumé du contenu de la page N° 10

FIGURE 2 OUTLINE AND DIMENSIONAL SKETCH 10 Y1-03-0165 Rev. D

Résumé du contenu de la page N° 11

FIGURE 3 INSTRUCTION PLATE LABEL 11 Y1-03-0165 Rev. D