Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
CONTENTS Introduction and Important Safety Information 3-5 Component Identification 6 Assembly Instructions 7 Operating Instructions 8-9 Detergents and Clean Up Tips 10 Shut Down and Clean-Up 11 Storage 11 Maintenance 1-14 Troubleshooting 15-18 Maintenance and Oil Change Charts 19 Exploded View, Left Side 0 Exploded View, Right Side 1 Exploded View, Parts List -4 Steam Pump, Exploded View and Parts List 5 Control Panel, Exploded View 6 Control Panel, Exploded View Parts List 6-7 Float
Résumé du contenu de la page N° 3
PRESSURE WASHER OPERATOR’S MANUAL INTRODUCTION & IMPORTANT SAfETy INfORMATION Thank you for purchasing this Pressure Washer. WARNING: This machine exceeds WARNING 85 db appropriate ear protection We reserve the right to make changes at any time must be worn. without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings EAR PROTECTION before using this pressure washer. Warning info
Résumé du contenu de la page N° 4
IMPORTANT SAfETy INfORMATION In an overfilling situation, additional precautions are 15. Be certain all quick coupler fittings are secured necessary to ensure that the situation is handled before using pressure washer. in a safe manner. WARNING: High pressure devel- WARNING WARNING: Risk of injury. Disconnect battery oped by these machines will ground terminal before servicing. cause personal injury or equip- ment damage. Keep clear of 8. When in use , do not place machine near flammable
Résumé du contenu de la page N° 5
PRESSURE WASHER OPERATOR’S MANUAL IMPORTANT SAfETy INfORMATION 1. Do not allow acids, caustic or abrasive fluids to pass through the pump. . Never run pump dry or leave spray gun closed longer than 1- min utes. 3. Machines with shut-off spray gun should not be operated with the spray gun in the off position for extensive periods of time as this may cause dam- age to the pump. 4. Protect discharge hose from vehicle traffic and sharp objects. Inspect condition of high pressur
Résumé du contenu de la page N° 6
Résumé du contenu de la page N° 7
Résumé du contenu de la page N° 8
Résumé du contenu de la page N° 9
Résumé du contenu de la page N° 10
Résumé du contenu de la page N° 11
Résumé du contenu de la page N° 12
Résumé du contenu de la page N° 13
PRESSURE WASHER OPERATOR’S MANUAL MAINTENANCE Step 4 After circulating solution, flush the entire burner Nozzle: system with fresh water. Clean out float tank Keep the tip free of surface deposits by wiping it with and then reinstall wand assembly to spray a clean, solvent saturated cloth, being careful not to gun. plug or enlarge the nozzle. For maximum efficiency, replace the nozzle each season. Removal of Soot from heating Coil: In the heating process, fuel residue in the fo
Résumé du contenu de la page N° 14
MAINTENANCE Coil Removal: Removal of coil because of freeze breakage, or to clean soot from it can be done quickly and easily. 1. Disconnect hose from pump to inlet side of the coil. . Carefully disconnect the thermostat sensor making sure you do not crimp the capillary tube. 3. Remove burner assembly from combustion cham- ber. 4. Remove the 3-3/8" bolts from each side of coil and tank assembly (these bolts are used to fasten tank to chassis). 5. Remove fittings connected to
Résumé du contenu de la page N° 15
PRESSURE WASHER Troubleshooting Guide TROUbLEShOOTING PRObLEM POSSIbLE CAUSE SOLUTION LOW OPERATING Faulty pressure gauge Install new gauge. PRESSURE Insufficient water supply Use larger supply hose; clean filter at water inlet. Old, worn or incorrect spray nozzle Match nozzle number to machine and/or replace with new nozzle. Belt slippage Tighten or replace; use correct belt. Plumbing or hose leak Check plumbing system for leaks. Retape leaks with teflon tape. Faulty or misadjusted unload
Résumé du contenu de la page N° 16
TROUbLEShOOTING PRObLEM POSSIbLE CAUSE SOLUTION bURNER WILL NOT Flex coupling slipping on fuel pump Replace if needed. LIGhT shaft or burner motor shaft (continued from On-Off switch defective Check for electrical current reaching previous page) burner assembly with burner switch on. Heavy sooting on coil and burner Clean as required. can cause interruption of air flow and shorting of electrodes Improper electrode setting Check and reset according to diagram in Operator's Manual. Fuel not r
Résumé du contenu de la page N° 17
PRESSURE WASHER Troubleshooting Guide TROUbLEShOOTING PRObLEM POSSIbLE CAUSE SOLUTION LOW WATER Improper fuel or water in fuel Replace with clean and proper fuel. TEMPERATURE Low fuel pressure Increase fuel pressure. Weak fuel pump Check fuel pump pressure. Replace pump if needed. Fuel filter partially clogged Replace as needed. Soot build-up on coils not allowing heat Clean coils. transfer Improper burner nozzle See burner specifications. WATER Incoming water to machine warm or hot Lower i
Résumé du contenu de la page N° 18
TROUbLEShOOTING PRObLEM POSSIbLE CAUSE SOLUTION OIL DRIPPING Oil seal worn Check and replace if necessary. ExCESSIvE vIbRATION Irregular functioning of the valves Check and replace if necessary. IN DELIvERy LINE DETERGENT Air leak Tighten all clamps. Check detergent lines NOT DRAWING for holes. Restricter in float tank is missing Replace restricter. Check for proper orifice in restricter. Filter screen on detergent suction Clean or replace. hose plugged Dried up detergent plugging Disassembl
Résumé du contenu de la page N° 19
PRESSURE WASHER OPERATOR’S MANUAL PREvENTATIvE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer
Résumé du contenu de la page N° 20
