Résumé du contenu de la page N° 1
640t Laminator
INSTALLATION &
OPERATION MANUAL
Document Number: 04048E001
Do not duplicate without written permission.
Résumé du contenu de la page N° 2
640t – Installation and Operating Instructions The information in this publication is provided for the use of GBC customers. General Binding Corporation (GBC), and it’s parent ACCO Brands Corporation, make no guarantees or warranties in connection with this publication. ACCO and GBC expressly disclaim any liability for errors in this publication or for incidental or consequential damage in connection with the furnishing or use of the information in this publication, including, but not li
Résumé du contenu de la page N° 3
640t – Installation and Operating Instructions T elab fo Cno Tne Ts 1. Safety E. Unwind/Supply Shaft ....................................... 5-5 Power ..................................................................... 5-6 Warnings .................................................................1-1 A. On/Off Power Switch ....................................... 5-6 General ....................................................................1-1 B. Circuit Breaker ...............................
Résumé du contenu de la page N° 4
640t – Installation and Operating Instructions Page ii
Résumé du contenu de la page N° 5
640t – Installation and Operating Instructions 1. s etaf y Your safety, as well as the safety of others is W arnings important. Before you install or use the machine, read and follow all the safety notices carefully in • Do not attempt to service or repair the this chapter. In this instruction manual, and on the laminator. laminator, you will find important safety notices • Do not connect the laminator to an electrical regarding the laminator. Read all of the instructions supply or attempt
Résumé du contenu de la page N° 6
640t – Installation and Operating Instructions e al rictc e l The laminator should be connected only to a source of power as indicated in these instructions and on the serial plate located on the rear of the laminator. Contact an electrician should the attachment plug provided with the laminator not match the receptacles at your location. WARNING: Do not attempt to service or repair the laminator. Failure to observe this warning could result in severe personal injury or death. Disconnec
Résumé du contenu de la page N° 7
640t – Installation and Operating Instructions 2. Warrtany l eitdmi 90-d y a Warratn y This limited warranty shall be void if the laminator has been misused; mishandled; damaged by GBC warrants to the original purchaser for a negligence, by accident, during shipment, or due to period of ninety days on labor and on parts after exposure to extreme conditions; repaired, altered, installation that this laminator is free from defects moved, or installed by anyone other than GBC or in workmanship
Résumé du contenu de la page N° 8
640t – Installation and Operating Instructions Page 2-2
Résumé du contenu de la page N° 9
640t – Installation and Operating Instructions 3. s noistaciifcep 640t Maximum film roll diameter 5 inches Operating Speed • Variable 3 to 16 fpm (0.8 to 4 m) • Fixed 3 fpm (0.9 m)* Dimensions • Width 78 in (198 cm) • Height 48 in (122 cm) • Depth 30 in (76 cm) • Weight 350 lbs. (273 kg) Electrical Requirements • Voltage 220 VAC 60 Hz • Current 9 Amps • Power 2000 W • U.S. Receptacle NEMA 6-15R *NOTE: The 640t laminator has a fixed speed in reverse or when using the foot pedal with th
Résumé du contenu de la page N° 10
640t – Installation and Operating Instructions c cf n e t o m ionts a icodif This equipment has been tested and found to Any modifications made to this device that are not comply with the limits for a Class A digital device, approved by General Binding Corporation, an ACCO pursuant to part 15 of the FCC Rules. These limits Brands Corporation, may void the authority granted are designed to provide reasonable protection to the user by the FCC and/or by Industry Canada to against harmful interf
Résumé du contenu de la page N° 11
640t – Installation and Operating Instructions 4. i onit lal a nst This chapter describes how to install the machine. i iont lal a nst There are no operator serviceable parts to the machine other than periodic cleaning. Refer to To set up the laminator for the first time: “7. Operator Maintenance” on page 7-1. 1. Place the laminator on a stable flat surface capable of supporting the weight of the machine. An additional work surface near the laminator is WARNING: Do not attempt to service o
Résumé du contenu de la page N° 12
640t – Installation and Operating Instructions Page 4-2
Résumé du contenu de la page N° 13
640t – Installation and Operating Instructions 5. f uret e a ueidg This chapter helps you identify the main components of the laminator. Release liner take-up Top film supply shaft Pressure roller Safety sensor Control panel Feed table Feed table interlock latch (under table) Roller pressure handle Bottom supply shaft Foot switch Fig. 5-1. Laminator Identification. A. Release Liner Take-up f mil s haf ts Rewinds the release liner of pressure sensitive films. It consists of a shaft, core
Résumé du contenu de la page N° 14
640t – Installation and Operating Instructions i erdl Bars , u n Wind s haf ts , r esrlol and s eatf y s ensor r e Wind s haf ts Fig. 5-4 Upper and Lower Main Rollers and Safety Sensor. a . u erpp m ain r erlol Fig. 5-3. Idler Bars, Unwind Shafts, Rewind Shafts. The Upper Main Roller lowers onto the Lower Main Roller to create the nip or the point at which the top a . u erpp r e Wind and bottom rollers come into contact and the point at which the items to be laminated are introduced to B.
Résumé du contenu de la page N° 15
640t – Installation and Operating Instructions e ygmeernc s op t and t a Bel c olrton p anel and p trin c l amp Fig. 5-5. Emergency Stop Button and Table Components. Fig. 5-6. Control Panel and Print Clamp a . t a Bel i kco ertln h eol and Lock Release Latch. When the table is down, the latch engages this hole. a . c olrton p anel & d y ilsp a B. t a Bel i kco ertln Allows the operator to control the speed and The Table Interlock latch locks the feed table into temperature of the rollers.
Résumé du contenu de la page N° 16
640t – Installation and Operating Instructions t ension c olrston r erlol p sresure h aendl Fig. 5-7. Tension Knobs and Brakes Fig. 5-8. Roller Pressure Handle. a . r eelsae l iner t ension k no B a . m intguon & l intgamina p rseets Use the Release Liner Tension Knob to increase and Mounting and Laminating Presets are located on decrease the amount of Pull that is being applied the side cover. The decal describes the gap and to the release liner. This prevents the release liner downward p
Résumé du contenu de la page N° 17
640t – Installation and Operating Instructions r e Winedr m edia c ore a apertd Fig. 5-10. Rewinder Components. a . r e Winder c ore a aperstd The Rewinder Core Adapters are held in place Fig. 5-9. Media Core Adapter. using friction. They adapt to the provided 2-1/4 inch The Media Core Adapters hold and lock the rolls of cardboard tube and most media tubes. film and release liner on the shafts to prevent side to side shifting. Grippers on the Core Adapters ensure B. r e Winder s haf t pr
Résumé du contenu de la page N° 18
640t – Installation and Operating Instructions p o Wer p o Wer c ord and f t oo s Whcti Fig. 5-12. Power Cord and Foot Switch. Fig. 5-11. Power Panel. a . p o Wer c ord a . o n /o ff p o Wer s Whcti The Power cord is a 220 VAC, NEMA 6-15P and fits a The On/Off Power Switch is located at the back of NEMA 6-15R. the machine. Press the “I” on the switch to turn it on. The LCD will illuminate. The off position, marked “0”, B. f t oo s Whcti turns the machine off. The Foot Switch allows the op
Résumé du contenu de la page N° 19
640t – Installation and Operating Instructions t emp s iontc e c olrton p anel D. MES (Measure) A Press MES to show the actual Top Main Roller Temperature. C E. Temp Arrow Up B To increase the Top Main Roller temperature, press and hold. F. Temp Arrow Down To decrease the Top Main Roller temperature, press and hold. G. HOT D For the factory preset temperature of the Top Main Roller, press HOT. E G H. COLD F H For the factory preset temperature of the Top Main Roller, press COLD I
Résumé du contenu de la page N° 20
640t – Installation and Operating Instructions Page 5-8
