Résumé du contenu de la page N° 1
DO NOT
DISCARD
R
CLASSIC BAY 1200 PELLET STOVE
Owner’s Manual Tested and Portland
O-T L
Oregon USA
Listed by
Installation and Operation
C US
OMNI-Test Laboratories, Inc.
Model:
CB1200-B
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and • Leave this manual with
• Important operating and
follow these instruc- party responsible for use
maintenance instruc-
tions for safe installa- and operation.
tions included.
tion and operation.
WARNING
WARNING
HOT SURFACES!
Please read this entire m
Résumé du contenu de la page N° 2
R R R CB 1200 Pellet Stove and Welcome to the Quadra-Fire Family! of our stoves, inserts and fireplaces. And yet we are old- Hearth & Home Technologies welcomes you to our tradi- fashioned when it comes to craftsmanship. Each unit is tion of excellence! In choosing a Quadra-Fire appliance, meticulously fabricated and surfaces are hand-finished for you have our assurance of commitment to quality, durabil- lasting beauty and enjoyment. Our pledge to quality is com- ity, and performance.
Résumé du contenu de la page N° 3
R R R CB 1200 Pellet Stove TABLE OF CONTENTS Section 1: Listing and Code Approvals Section 8: Operating Instructions A. Appliance Certifications ......................4 A. Fuel Size & Material ............................22 B. Mobile Home Approved ......................4 B. General Operation Information ...........22 C. Glass Specifications ............................4 C. Before Your First Fire .........................2 D. Electrical Rating ..................................4 D. Star
Résumé du contenu de la page N° 4
R R R CB 1200 Pellet Stove Listing and Code Approvals 1 A. Appliance Certification E. BTU & Efficiency Specifications Model CB1200 Pellet Stove Emissions Rating 0. 9 grams/hr . Laboratory OMNI Test Laboratories, Inc. *BTU Output 14,000 - 40,000 / hr Report No. 061-S-21-4 Heating Capacity up to 2,500 sq. ft. depending on climate zone Type Solid Fuel Room Heater/Pellet Fuel Hopper Capacity 80 lbs BurningType Fuel Wood Pellets or Shelled Corn Standard ASTM E1509-95, ULC S627-M9 and Shippin
Résumé du contenu de la page N° 5
R R R CB 1200 Pellet Stove Getting Started 2 A. Design, Installation & Location B. Fire Safety Considerations Maintain the designated clearances to combustibles. Insu- 1. Appliance Location lation must not touch the chimney. You must maintain the designated air space clearance around the chimney. This Consideration must be given to safety, convenience, traffic space around a chimney is necessary to allow natural heat flow, and the fact that the appliance will need a chimney and remov
Résumé du contenu de la page N° 6
R R R CB 1200 Pellet Stove C. Tools And Supplies Needed D. Inspect Appliance & Components and Pre-Use Check List Tools and building supplies normally required for installation, unless installing into an existing masonry fireplace: 1. Place the appliance in a location near the Reciprocating Saw Safety Glasses final installation area and follow the proce- Channel Locks Framing Square dures below: Hammer Electric Drill & Bits (1/4”) 2. Open the appliance and remove all the parts Phillips S
Résumé du contenu de la page N° 7
R R R CB 1200 Pellet Stove Dimensions and Clearances 3 A. Appliance Dimensions 4-5/8 in 20- 7/16 in. 8-1/6 in. (118mm) (519mm) (205mm) 12-/8 in (14mm) 14-1/4 in C L (62mm) 5.0 in 2-1/2 in C (127mm) L (64mm) 25-/4 in. 27-5/8 in. (654mm) (692mm) 28-1/2 in. (724mm) Figure 7.2 - Top View with Top Vent Adapter Figure 7.1 - Top View 28-1/2 in. 25-/4 in. (724mm) (629mm) 1-5/8 in. (80mm) C L 10-/4 in. 8-1/16 in. (27mm) (205mm) 24-/4 in. 26-1/2 in. (629mm) (67mm) Figure 7.3 - Side View Fi
Résumé du contenu de la page N° 8
R R R CB 1200 Pellet Stove B. Clearances to Combustibles (UL and ULC) Alcove Installation Inches Millimeters Minimum Alcove Height 44 1117 Minimum Alcove Width 40-1/2 1029 A C Maximum Alcove Depth 6 915 Minimum Alcove Side Wall 6 152 Top of Unit to Combustibles 12-1/2 18 B C WARNING Fire Risk. Inches Millimeters Straight Back Against Comply with all minimum clearances to Wall combustibles as specified. Back Wall to Appliance 2 51 A Failure to comply may cause house fire. Side Wall to App
Résumé du contenu de la page N° 9
R R R CB 1200 Pellet Stove C. Hearth Pad Requirements (UL and ULC) Alcove Installation Inches Millimeters Minimum Alcove Height 44 1117 Use a non-combustible floor protector, extending beneath Minimum Alcove Width 40-1/2 1029 appliance and to the front, sides and rear as indicated. Measure front distance “M” from the surface of the glass Maximum Alcove Depth 6 915 door. Minimum Alcove Side Wall 6 152 Top of Unit to Combustibles 12-1/2 18 L* K K M Figure 9.1 Inches Millimeters Hearth Pad
Résumé du contenu de la page N° 10
R R R CB 1200 Pellet Stove Vent Information 4 B. Venting Termination Requirements A. Chimney and Exhaust Connection 1. Chimney & Connector: Use or 4 inch (76-102mm) diameter type "L" or "PL" venting system. It can be CAUTION vented vertically or horizontally. Do not terminate vent in any enclosed or semi-enclosed 2. Mobile Home: Approved for all Listed pellet vent. If area such as a carport, garage, attic, crawl space, under a using the inch (76mm) vertical top vent adapter Kit
Résumé du contenu de la page N° 11
R R R CB 1200 Pellet Stove WARNING C. Equivalent Feet of Pipe Improper installation, adjustment, alteration, service or The table below can help you calculate the equivalent feet maintenance can cause injury or property damage. Refer of pipe which is a method used to determine pellet vent size. to the owner’s information manual provided with this appli- Figure 11.1. ance. For assistance or additional information consult a qualified installer, service agency or your dealer. Example of 3
Résumé du contenu de la page N° 12
R R R CB 1200 Pellet Stove Venting Systems 5 A. Alcove A C D B Figure 12.1 Inches Millimeters Alcove Installation Minimum Alcove Height 44 1117 A Minimum Alcove Width 40-1/2 1029 B Maximum Alcove Depth 6 915 C Minimum Alcove Side Wall 6 152 D not shown Top of Unit to Combustibles 12-1/2 18 All minimums listed are to a combustible surface. NOTE: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. • Illustrations/diagrams are not drawn to scale. • Actual installat
Résumé du contenu de la page N° 13
R R R CB 1200 Pellet Stove B. Through The Wall NOTE: Horizontal termination cap must be a minimum of 12 inches. In Canada, where passage through a wall or partition of (05mm) from the wall. Approved for mobile home instal- combustible construction is desired, the installation shall lations. Must use or 4 inch (76-102mm) “L” or “PL” listed conform to CAN/CSA-B65 pellet venting or listed double wall pipe and a Quadra-Fire outside air kit in mobile homes. 2 in. Straight Out (51mm) Mi
Résumé du contenu de la page N° 14
R R R CB 1200 Pellet Stove C. Vertical We recommend a minimum of 60 in. Rain Cap (1524mm) vertical, however above the eave is preferred. Both installations are approved for mobile home installations. Must use or 4 inch (76 Flashing 24 in. (610mm) to 102mm) “L” or “PL” Listed pellet venting or minimum listed double wall pipe and Quadra-Fire out- side air kit in mobile homes. Single wall pipe is approved for residential installations only. Firestop Class A Chimney Connector Adapte
Résumé du contenu de la page N° 15
R R R CB 1200 Pellet Stove WARNING Fire Hazard Inspection of Chimney: • Masonry chimney must be in good condition. • Meets minimum standard of NFPA 211 • Factory-built chimney must be 6 in. (152mm) UL10 HT. E. Masonry Fireclay Flue Concrete Cap Liner with Airspace Flashing 1 in. (25mm) Clearance with Firestop 1 in. (25mm) Clearance in. (76mm) Minimum 6 in. (152mm) Sheathing Minimum Cleanout Cover Airtight Clean-out Door Non-Combustible Hearth Pad Figure 15.1 F. Alternate Masonry Fireclay
Résumé du contenu de la page N° 16
R R R CB 1200 Pellet Stove Mobile Home 6 A. Mobile Home Installation CAUTION You must use a Quadra-Fire Outside Air Kit Maintain structural integrity of mobile home: for installation in a mobile home. • Floor, wall, ceiling and/or roof. Do NOT cut through: 1. An outside air inlet must be provided for the combustion • Floor joist, wall, studs or ceiling trusses. air and must remain clear of leaves, debris, ice and/or • Any supporting material that would affect the structural snow. It mus
Résumé du contenu de la page N° 17
R R R CB 1200 Pellet Stove Appliance Set-Up 7 A. Outside Air Kit Instructions 2. Floor Installation a. Remove rear screen and set aside. Included in Kit: 1 piece of 2 inch x foot flex hose, 2 hose b. Install cover plate over hole in right rear floor. clamps, 1 collar assembly, termination cap assembly, 1 trim ring, 12 screws. c. Cut a 2 inch minimum hole in the floor to accommodate Tools Needed: Phillips head screw driver; wire cutters; flex hose. hole saw or jig saw. d. Attach hose t
Résumé du contenu de la page N° 18
R R R CB 1200 Pellet Stove C. Rear Vent and Rear Vent to Top Vent B. Top Vent Adapter Installation Adapter Installation 3 to 3 inch Top Vent Adapter 3 to 6 inch Top Vent Offset Adapter Installing the Top Vent Adapter 1. Put a layer of high temperature silicone on the inch (76mm) exhaust outlet. 2. Slide the top vent adapter onto the rear exhaust outlet and adjust the assembly to a vertical position. . Drill 4 holes with #26 drill bit (provided) into the back of the appliance usi
Résumé du contenu de la page N° 19
R R R CB 1200 Pellet Stove E. Brick Clip Installation D. Optional Brick Set Installation 1. Remove the baffle first, follow instructions on page 33. WARNING 2. Slide bottom of left rear brick in first; rotate top edge Risk of Injury. toward rear of appliance and then rotate outer edge • Brick may have small wires protruding from toward rear of appliance, until brick slides into place. the back of brick. Figure 19.1. . Repeat with right rear brick. 1. After the brick set has been install
Résumé du contenu de la page N° 20
R R R CB 1200 Pellet Stove F. Optional Log Set Placement Instructions G. Optional Gold or Nickel Grille Assembly CAUTION CAUTION Do not open top all the way back so the weight of the Logs are FRAGILE. Use extreme care when handling or top is supported by the hinges. It will damage the cleaning logs. hinges. It will be necessary to prop the top up with a supporting brace. You can use the shipping box as shown in Figure 1. 1. Place the front log in first as shown in Figure 20.1. Plac
