Résumé du contenu de la page N° 1
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Sienna
B Y : S H E R W O O D I N D U S T R I E S L T D
OWNER’S
MANUAL
WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of
life. Installation and service must be
performed by a qualified installer, service
agency or the gas suppl
Résumé du contenu de la page N° 2
Safety Precautions FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION: • All ENVIRO gas-fired appliances must be installed • To prevent injury, if the pilot or pilot and in accordance with their instructions. Carefully read all burners have gone out on their own, open the the instructions in this manual first. Consult the building glass door and wait 5 minutes to air out before authority having jurisdiction to determine the need for a
Résumé du contenu de la page N° 3
Table of Contents Safety Precautions.....................................................................................................2 Table of Contents......................................................................................................3 Codes And Approvals.................................................................................................4 Specifications............................................................................................................
Résumé du contenu de la page N° 4
Codes And Approvals DIRECT VENT: This type is identified by the suffix DV. This appliance draws all of its air for combustion from outside the dwelling, through a specially designed vent pipe system. This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level. BV: This Vented appliance draws all of its combustion air from the dwelling and must be vented using listed B or L vent. May also be vented through a conventional chimney using a chimne
Résumé du contenu de la page N° 5
Specifications RATING LABEL LOCATION: The rating label is located under the control panel and is attached to a rectangular metal sheet that is chained to the fireplace. DIMENSIONS: Table 1: Sienna exterior dimensions. (Shaded dimensions shown in Figure 1 & 2.) Surround Style Distance Direct Vent B-Vent 11 9 Arched Surround From Flue To Surround 14 /16” (376 mm) 14 /16” (370 mm) 5 From Back/Sensor To Surround 17 /16” (439 mm) 18 7⁄8” (479 mm) 33” x 46” (840 x 1930 mm) From Flue To Surround 14 1⁄
Résumé du contenu de la page N° 6
Specifications 21" ( 5 33 m m ) S en s or S how n : B - V e n t w i th 3 3 " x 4 6" ( 84cm x 193 c m ) sur r ou nd pan e l w i t h t r i m F l u e 3 1 7 / 8 " ( 441 m m ) 1 13 / 1 6 " ( 333 m m ) 1 3 W i t h T r i m 4 6 / 8 " ( 1 17 1 m m ) 1 / 8 " W i tho ut T r i m 46" ( 1 16 8 m m ) ( 36 m m ) W i th T r i m 3 3 3 / 1 6 " ( 3 4 3 m m ) W i th o u t T r i m 3 3 " ( 3 3 8 m m ) 1 30 / 2 " ( 7 75 m m ) 11 3 22 / 16 " 2 2 / 4 " 1 ( 576 m m ) ( 5 77 m m ) 15 / 1 6 " ( 38 3 m m ) 5 2 0 / 8 " ( 5 2
Résumé du contenu de la page N° 7
L O I P T O L T P T H T P T H I P F F Operating Instructions For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE. PILOT LIGHTING INSTRUCTIONS: H o t wh ile o p er at i n g . D o n o t t o u c h , s ever e b u r n s m a y r esu l t . K eep ch il d r e n , c l o t hi ng, C A U T I ON : f u r n it u r e , g aso lin e o r o
Résumé du contenu de la page N° 8
Operating Instructions For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating TURN OFF UNIT: Flip switch to OFF to turn off burners only. If the fireplace is to be turned off for the season, or for servicing, turn the gas shut off valve to OFF. If the unit is going to be serviced, turn off the electrical power to the unit as well. NOTE: When the unit is turned on for the first time, it should be turned onto high, with the fan OFF, for the first two to four hours.
Résumé du contenu de la page N° 9
Maintenance And Service Warning: Failure to position the parts in accordance with this manual, or failure to use only parts specifically approved with this appliance, may result in property damage or personal injury. At least once a year, run through the following procedures to ensure the system is clean and working properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not blocked by anything (see Figure 4). The pilot flame should be blue
Résumé du contenu de la page N° 10
Maintenance And Service QUALIFIED INSTALLERS ONLY GLASS DOOR REMOVAL: Open the door by removing the two (2) 5 /16’’ bolts located at the top outside corners of the glass frame (see Figure 8). Lift the bottom of the door up and remove from unit (see Figure 9). CAUTION GLASS MAY SEPARATE FROM DOOR. Figure 9: Bottom hooks for Figure 8: Top bolts for glass door. glass door. BURNER & BLOWER REMOVAL: 1. Turn the unit off and allow the unit to cool completely. 2. Remove the fascia or louvers, op
Résumé du contenu de la page N° 11
Maintenance And Service FUEL CONVERSION: TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY Please read and understand these instructions before installing. Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result c
Résumé du contenu de la page N° 12
Maintenance And Service 5 b) Insert a /32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 12), rotate it counter-clockwise until it is free and extract it. c) Check that the screw is clean and if necessary L o o s e n remove dirt. T i g h t e n d) Flip the screw (refer to Figure 13). e) Using the Allen wrench as shown in Figure 12, rotate the screw clockwise until a torque of 9 inch lbs. WARNING! Do not over tighten the screw. It is recommended that you grip the
Résumé du contenu de la page N° 13
Initial Installation WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. CLEARANCES TO COMBUSTIBLES: Maintain sufficient clearances for operation, service and maintenance. • A clearance of 25 1⁄2” (648 mm) minimum is required from the center of the unit to the sidewalls. • A 2” (51 mm) wide mantel can be mounted at a minimum height of 39” (991 mm) from the bottom 1 0" (254 m
Résumé du contenu de la page N° 14
Initial Installation WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. MINIMUM FIREPLACE SIZE: Table 2: Minimum dimensions of fireplace for Sienna to be installed into. Description of Fireplace Dimension Direct Vent B-Vent At Back 23 1⁄4” (591 mm) 23 1⁄4” (591 mm) Width At Front 35” (889 mm) 35” (889 mm) With Surround Only 23 3⁄4” (603 mm) 23 3⁄4” (603 mm) Height With Surro
Résumé du contenu de la page N° 15
Initial Installation QUALIFIED INSTALLERS ONLY DIRECT VENT MODEL: WARNING: This appliance has been designed to draw room air for proper heat circulation from the sides of the unit. Blocking or modifying the louvers in any way can create hazardous situations. This model is vented with two (2) 3” aluminum or stainless steel flex vents leading into a co-linear to co-axial vent adaptor and using a vertical termination cap. The flue collars of this model will fit inside of a standard 3” vent and
Résumé du contenu de la page N° 16
Initial Installation QUALIFIED INSTALLERS ONLY VENTING FIREPLACE INSERTS: The ENVIRO SIENNA may be installed and vented into any solid fuel fireplace that has been installed in accordance with the National, Provincial/State and local building codes and has been constructed of non-combustible materials. This appliance must not be connected to a chimney flue serving a separate solid fuel-burning appliance. Before starting refer to INITIAL INSTALLATION - PREPARING YOUR SIENNA FOR INSTALLATION a
Résumé du contenu de la page N° 17
Initial Installation QUALIFIED INSTALLERS ONLY Table 3: Vent termination clearances Minimum Clearance Description Clearance above the highest point where it passes through a roof surface, refer 3 ft (0.9 m) to Figure 21. Clearance above a roof ridge, any other portion of a building, or any other ob- 24 in (0.6 m) struction within a horizontal distance of 10 feet (3 m), refer to Figure 21. Clearance for a vent or chimney above either the highest connected appliance 5 ft (1.5 m) drafthood outlet
Résumé du contenu de la page N° 18
Initial Installation QUALIFIED INSTALLERS ONLY ELECTRICAL REQUIREMENTS: The fan is thermostatically controlled and it will not operate if the appliance is cold. A few minutes after the appliance is lit and the variable speed control is set at a desired setting, the fan will automatically turn on. The fan will automatically turn off after the appliance has cooled down. The fireplace must be electrically grounded in accordance with local codes or, in the absence of local codes, with the cu
Résumé du contenu de la page N° 19
L O I P T O L T P T H T P T H I P F F Initial Installation QUALIFIED INSTALLERS ONLY GAS LINE CONNECTION: Warning: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance. Gas Line Connection: •This fireplace is equipped with a certified flexible pipe located on the right side of the unit, terminating in a 3⁄8” male NPT fitting. Consult the local authorities for local codes or use the CAN/CGA B149 (1 or 2) installation code in Canada. In the U
Résumé du contenu de la page N° 20
Initial Installation QUALIFIED INSTALLERS ONLY CONVERTING A DIRECT VENT FIREPLACE TO A B-VENT FIREPLACE: 1. Remove the Direct Vent chimney connector assembly by taking out the two (2) T-20 screws at the front of the unit. Push the assembly out from under the brackets at the back and remove (see Figure 24). D i r e ct V e nt 2. Remove the two (2) fresh air C o n ne ct or A sse mbl y inlet covers from each side. Cover locations shown in Figure 25. 3. Slide the B-Vent chimney connector a
