Résumé du contenu de la page N° 1
Owner’s Manual
Installation and Operation
Model:
QVI-30FB
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS INSTALLERS
WARNING: IMPROPER INSTALLA-
GUIDE MUST BE LEFT WITH APPLIANCE FOR
TION, ADJUSTMENT, ALTERATION,
FUTURE REFERENCE.
SERVICE OR MAINTENANCE CAN
CAUSE INJURY OR PROPERTY DAM-
AGE. REFER TO THIS MANUAL. FOR
WARNING: IF THE INFORMATION
ASSISTANCE OR ADDITIONAL INFOR-
IN THESE INSTRUCTIONS IS NOT
MATION CONSULT A QUALIFIED IN-
FOLLOWED EXACTLY, A FIRE OR
STALLER, SER
Résumé du contenu de la page N° 2
SAFETY AND WARNING INFORMATION These units MUST use one of the vent systems READ and UNDERSTAND all instructions carefully ! ! described in the Installing the Fireplace section of before starting the installation. FAILURE TO the Installers Guide. NO OTHER vent systems or FOLLOW these installation instructions may result components MAY BE USED. in a possible fire hazard and will void the warranty. This gas fireplace and vent assembly MUST be Prior to the first firing of the fireplace, READ the !
Résumé du contenu de la page N° 3
TABLE OF CONTENTS Safety and Warning Information ................................................ 2 Service Parts Lists ..................................................................... 4 Section 1: Approvals and Codes ............................................... 7 Appliance Certification................................................................... 7 Installation Codes.......................................................................... 7 High Altitude Installations ..........
Résumé du contenu de la page N° 4
Service Parts QVI-30FB Service Parts Diagram 8 20 9 10 19 12 11 18 13 17 14 15 Log Set Assembly 16 6 5 1 4 7 2 3 Part number list on following page. 4 Quadra-Fire • QVI-30FB • 2020-900 Rev. H • 9/07
Résumé du contenu de la page N° 5
Service Parts List QVI-30FB IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your AVAILABLE dealers' VIP site. When ordering, supply serial and model numbers to ensure correct service TO SHIP IN parts. 24 HOURS ITEM DESCRIPTION SERIAL # PART NUMBER LOGS-QVI30FB Log Set Assembly Y SRV2020-140 1 Log 1 SRV2020-141 2 Log 2 SRV2020-142 3 Log 3 SRV340-704 4 Log 4 SRV340-706 5 Log 5 SRV340-705 6 Log 6 SRV740-707 7 Log 7 783-108A 8 Slide Plate Assembly 2019-201
Résumé du contenu de la page N° 6
Service Parts QVI-30FB Valve Assembly Parts Diagram Standing Pilot Valve Assembly 6 7 1 8 2 9 3 4 5 10 IMPORTANT: THIS IS DATED INFORMATION. The most current information is located AVAILABLE on your dealers' VIP site. When ordering, supply serial and model numbers to ensure TO SHIP IN correct service parts. 24 HOURS ITEM DESCRIPTION SERIAL # PART NUMBER Flex Ball Valve Assembly 302-320A 1 Y Valve NG 060-522 Y 2 Valve LP 060-523 Y 3 Pilot control Knob 571-530 Flame Control Knob 571-531 4 5 Val
Résumé du contenu de la page N° 7
Approvals and Codes 1 Appliance Certification High Altitude Installations U.L. Listed gas appliances are tested and approved with- The Quadra-Fire appliance discussed in this Installers Guide out requiring changes for elevations from 0 to 2,000 feet in has been tested to certification standards and listed by the the U. S. A. and in Canada. applicable laboratories. When installing this appliance at an elevation above 2,000 feet, it may be necessary to decrease the input rating by Certification ch
Résumé du contenu de la page N° 8
Inspection NOTE: The following requirements reference various The state or local gas inspector of the side wall horizontally Massachusetts and national codes not contained in vented gas fueled equipment shall not approve the installa- this document. tion unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4. Requirements for the Commonwealth of Exemptions Massachusetts The following equip
Résumé du contenu de la page N° 9
Getting Started 2 Introducing the Quadra-Fire Gas Appliances WARNING: A HEARTH OR HEARTH EXTEN- ! SION (IF PRESENT) MUST COMPLY WITH EI- Quadra-Fire direct vent gas appliances are designed to THER OF THE FOLLOWING: 1) THE SOLID- operate with all combustion air siphoned from outside of FUEL BURNING FIREPLACE MANUFACTURER’S the building and all exhaust gases expelled to the outside. SPECIFICATION, OR 2) LOCAL BUILDING CODES The information contained in this Installers Guide, unless REQUIRED BY AUT
Résumé du contenu de la page N° 10
INLET AIR STARTING COLLAR SURROUND EXHAUST STARTING COLLAR DOOR ON/OFF SWITCH GLASS ASSEMBLY RATING PLATE GAS CONTROL VALVE ELECTRICAL JUNCTION BOX ACCESS GAS ACCESS B TOP VIEW C 2” (50.8mm) A QVI-30FB MINIMUM FIREPLACE SIZE Location Inches Millimeters A Front Width 30-1/4 768 B Rear Width 19 483 C Depth 14-1/8 359 * Height 22-1/2 572 * NOTE: If exhaust collar on insert and fireplace damper do not line up, add 4 inches (102mm) to minimum fireplace height for bends in vent pipe. Figure 1.
Résumé du contenu de la page N° 11
Dimensions in brackets are millimeters. A 5-9/16 [] 142 B 2-1/2 [] 64 REF 4 2-1/16 [] 102 [] 52 13-3/4 [] 350 3-1/8 [] 80 C ø ( 2-13/16 2) D [] 71 F H E G 1-1/16 [] 28 GAS INLET ELECTRICAL 1-9/16 6-5/8 ACCESS 3-9/16 [] 40 [] 169 (IF EQUIPPED) [] 91 QVI-30FB MODEL DIMENSIONS Location Inches Millimeters A 18 457 B6-1/2 165 C 29-3/8 746.1 D 26-1/16 661 E 20-5/8 524 F 14-5/8 371 G 22-1/8 562 H 21-1/4 540 Figure 2. Diagram and model dimensions Quadra-Fire • QVI-30FB • 2020-900 Rev. H • 9/07
Résumé du contenu de la page N° 12
Installing the Insert 3 A vertical vent termination system installed on this model Step 1. Installing the Vent System will require one (1) length of 3” stainless steel liner, one (1) length of 3-inch flexible vent pipe for the combustion air, Vent System Installation Precautions one (1) length of 3-inch flexible vent pipe for the exhaust air Before starting installation of vent kits, the installer should and one (1) Termination Cap. read these instructions and the Vent Kit Instructions to ensu
Résumé du contenu de la page N° 13
Attach the flashing and termination cap HORIZONTAL OVERHANG to the top of the flexible vent pipe and set the cap in place. See Figures 4 and 5. CAUTION: TO AVOID DOWNDRAFTS AND/OR COLD AIR PROBLEMS, IT IS VERTICAL WALL 2 FT. 2 FT. MIN. RECOMMENDED TO SEAL OFF THE MIN. AREA BETWEEN THE TERMINATION LOWEST DISCHARGE CAP AND THE TOP OF THE SOLID- OPENING FUEL CHIMNEY OPENING INTO TERMINATION CAP WHICH THE VENT CAP HAS BEEN IN- STALLED. X WHEN USING THE LINK-DV4-30 VENT 12 SYSTEM, IT IS REQUIRED TO
Résumé du contenu de la page N° 14
This option shows both exhaust and inlet air vent pipes attached to the adaptor. TERMINATION CAP FLASHING INLET AIR COLLAR EXHAUST COLLAR EXHAUST VENT PIPE V= 14 FT. MINIMUM 50FT. MAXIMUM 3 INCH COLLAR (Factory installed to stainless steel section) WARNING: DO NOT BLOCK PIPE END WITH INSULATION OR ANY OTHER SEALING MATERIAL STAINLESS STEEL PIPE - 3 FT. MIN. REQUIRED (INCLUDED) SEAL DAMPER AREA INLET AIR VENT PIPE COLLAR ATTACHMENT BRACKET Figure 4. WARNING: THE EXHAUST VENT PIPE MUST T
Résumé du contenu de la page N° 15
Note: Inspect for exhaust collar gasket to insure positive exhaust seal. LOCKING TABS ALTERNATIVE INSTALLATION FOR VENTING THROUGH WOOD-BURNING CLASS A PIPE LOCKING HANDLE TERMINATION CAP (SQUARE FLASHING REMOVED) EXHAUST VENT PIPE SUPPLIED WITH TERMINATION KIT INLET AIR VENT COLLAR (LINK-DV30 SHOWN) OPTIONAL LINK-ZC-ADPB (For Flashing Class-A Pipe) SLIDING PLATE CLASS A WOOD PIPE INLET AIR VENT PIPE 3 INCH STAINLESS STEEL COLLAR ADAPTER FOR EXHAUST (MUST BE INSTALLED) Figure 5. Typical configu
Résumé du contenu de la page N° 16
Step 2. Positioning, Leveling, and Step 4. The Gas Supply Line Securing the Insert Remote Control NOTE: Have the gas supply line installed in accordance The receiver for the remotes must be installed BETWEEN with local building codes by a qualified installer approved and/or licensed as required by the locality. the base pan of the insert and the firebox of the wood-burn- (In the Commonwealth of Massachusetts installation ing fireplace (see photo below). must be performed by a li
Résumé du contenu de la page N° 17
Step 5. Gas Pressure Requirements WARNING: MUST USE THE CORD SUPPLIED ! WITH THE J-BOX. Pressure requirements for these gas appliances are shown in the table below. • This appliance REQUIRES 110-120 VAC to operate. It is equipped with a blower. Pressure Natural Gas Propane NOTE: Electrical wiring must be installed by a li- Minimum 5.0 inches 11.0 inches censed electrician. Inlet Pressure w.c. w.c. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- Maximum Inlet 14.0 inches 14.0 inches SENT FOR EXTENDE
Résumé du contenu de la page N° 18
To service or clean: INSERT STRAIN RELIEF AROUND CORD IN THIS END • Remove the ground wire of the fan can clip on the side of FROM OUTSIDE OF UNIT the base pan. FEED PLUG THROUGH HOLE SIDEWALL • Remove the blower in between the bend up tabs. • Install and wire the blower per instruction shipped with the fan. • Reinstall the blower in reverse order. Make sure the fan does not make contact with the back wall. JUNCTION BOX SCREW Figure 9. PROVIDED Junction box installation COVER FAN PLATE Serving t
Résumé du contenu de la page N° 19
Step 7. Installing Logs and Ember Material BURNER PAN Shutter Settings Burner NG LP ___________________________________________ QVI-30FB 3/8” Full Open ___________________________________________ Positioning the Logs The logs have been packaged separately. Refer to the installation instructions that accompany this manual. Save EMBER MATERIAL (TOP SURFACE, the log instructions with this manual. AND FRONT
Résumé du contenu de la page N° 20
3. Attach the low voltage wires to the ON/OFF switch lo- Step 9. Before Lighting the Appliance cated on the front of surround. Before lighting the appliance, be sure to do the following: 4. Attach surround assembly by securing four corners with Remove all paperwork from the fireplace. screws provided (see Figure 14.) Reposition the fireplace Review safety warnings and cautions if necessary. Refer to surround instructions provided with the decorative surround. • Read the Safety and Warning Info
