Instruction d'utilisation Lennox Hearth ELITE EDVI35

Instruction d'utilisation pour le dispositif Lennox Hearth ELITE EDVI35

Dispositif: Lennox Hearth ELITE EDVI35
Catégorie: Cheminée
Fabricant: Lennox Hearth
Dimension: 2.47 MB
Date d'addition: 8/23/2014
Nombre des pages: 20
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Lennox Hearth ELITE EDVI35. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Lennox Hearth ELITE EDVI35.

Pour votre confort

Si regarder l'instruction Lennox Hearth ELITE EDVI35 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Lennox Hearth ELITE EDVI35 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Lennox Hearth ELITE EDVI35 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Lennox Hearth ELITE EDVI35 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 20 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Lennox Hearth ELITE EDVI35 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Lennox Hearth ELITE EDVI35. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1


INSTALLATION INSTRUCTIONS
MANUAL
DIRECT-VENT GAS FIREPLACE HEATER INSERTS
Elite™ Series, Models: EDVI25, EDVI30 & EDVI35
Suitable for installation into masonry or factory built fi replaces.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
P/N 775,156M Rev. G, 3/2005
Report No. 116-F-14-5
These appliances may be installed in an aftermarket permanently located,
manufactured (mobile) home, where not prohibited by local codes.
AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE
WARNING: IF THE INFORMATIO

Résumé du contenu de la page N° 2

These appliances comply with National CONGRATULATIONS ON THE PURCHASE OF YOUR NEW GAS APPLIANCE MANU- Safety Standards and are tested and listed FACTURED BY LENNOX HEARTH PRODUCTS. by OMNI-Test Laboratories Inc.; Beaverton, Oregon (Report No. 116-F-14-5) to ANSI When you purchased your new gas fi red heater, you joined the ranks of thousands of Z21.88 (in Canada, CSA-2.33), and CAN/ concerned individuals whose answer to their home heating needs refl ects their concern for CGA-2.17-M91 in bo

Résumé du contenu de la page N° 3

The millivolt appliances are manually con- CARBON MONOXIDE POISONING: EARLY Manifold Gas Supply Pressure (all models) trolled and feature a spark igniter (piezo) SIGNS OF CARBON MONOXIDE POISONING Fuel Low High that allows the appliance's pilot gas to be ARE SIMILAR TO THE FLU WITH HEAD- (LO) 1.6” WC (HI) 3.5” WC lit without the use of matches or batteries. Natural Gas (.40 kPa) (.87 kPa) ACHES, DIZZINESS AND/OR NAUSEA. IF This system provides continued service in the (LO) 6.3” WC (H

Résumé du contenu de la page N° 4

QUESTIONS TO ASK LOCAL BUILDING FIREPLACE REQUIREMENTS 6. Maximum amount of gas pipe without a OFFICIAL pressure test - type of test required? IMPORTANT: When installing these appliances 7. Are below grade penetrations of the gas These appliances must be installed per into a factory built fi replace or heatform, the air line allowed? manufacturers’ instructions. Installations fl ow within and around the fi replace shall not 8. Is concealed gas piping allowed? be altered by the installation of

Résumé du contenu de la page N° 5

SPECIFICATIONS: EDVI25 DIMENSIONS SPECIFICATIONS EDVI25 EDVI25 Inches (millimeters) Min. / Max. BTU hr 17,000 to 25,000 A 26 5/8" (676 mm) Input - NG B 20 1/2" (521 mm) Min. / Max. BTU hr 19,000 to 25,000 C 5” (127 mm) Input - LP D SM.= 41 1/16” (1043 mm) & MED.= 44 1/8” (1121 mm) Co-linear DV Vent 3” Dia. Liner SM.= 26 1/16” (662 mm) & MED.= 27 5/8” (702 mm) Size (exhaust & intake) E 19 1/2” (483 mm) F Room Blower CFM 110 cfm G 1 15/16” (49 mm) H

Résumé du contenu de la page N° 6

SPECIFICATIONS: EDVI30 & EDVI35 DIMENSIONS SPECIFICATIONS EDVI30 EDVI35 EDVI30 EDVI35 Inches (millimeters) Inches (millimeters) Min. / Max. BTU/hr 21,500 to 30,000 25,500 to 35,000 25 15/16" (659 mm) A 32 1/16” (814 mm) Input - NG B 22 1/4" (578 mm) 24 3/16” (614 mm) Min. / Max. BTU/hr 22,000 to 28,000 26,000 to 34,000 5" (127 mm) 5" (127 mm) C Input - LP D 40 1/4” (1022 mm)Sm. Co-linear DV Vent 3” Dia. Liner 3” Dia. Liner 45 3/4” (1162 mm) Med. 48 1/16” (1221 mm) Med.

Résumé du contenu de la page N° 7

MINIMUM CLEARANCES TO COMBUSTIBLES: EDVI25, EDVI30 & EDVI35 These appliances can be installed in most residential fi replace confi gurations. If installed close to an adjacent Inches (millimeters) wall, ensure that the minimum clearances to combustible Clearances to Combustibles Min. EDVI25 EDVI30 EDVI35 Max. surfaces are maintained. A local building inspector should A Side Wall 8" (203 mm) 8" (203 mm) 8" (203 mm) Min. review your plans prior to installation. B Ceiling or Alcove Height 64"

Résumé du contenu de la page N° 8

Step 4 LIFT INSERT INTO POSITION (read MINIMUM FIREPLACE DIMENSIONS CAUTION: If any portion of the chimney Fireplace Requirements on page 4 fi rst) Lift Refer to Figures 7 and 8 for Minimum Fire- system shows signs of structural or mechani- insert into position in front of the fi replace where place Clearance Dimensions. See pages 5 & cal weaknesses, such as: cracks, leaky unit is to be installed. Discard bottom carton. 6 for actual insert body dimensions. joints, corroded or warped surface

Résumé du contenu de la page N° 9

STEP 6: REMOVE PACKAGED MATERIALS FROM INSIDE FIREBOX AND Simpson Dura Vent Components SET ASIDE (log set, bag of embers, bag of vermiculite, propane Part No. Description conversion kit - if needed to run on LP gas). 980 Termination Cap, Standard Step 7: INSTALL LP CONVERSION KIT (IF NECESSARY) - Install the 991 Termination Cap, High Wnd LP conversion kit per instructions provided with kit. 923GK Chimney Liner Term. Kit Step 8: VENTING SYSTEM INSTALLATION (Refer to Vent Ma

Résumé du contenu de la page N° 10

Factory Built Fireplace Installation Diagram Masonry Fireplace Installation Diagram The standard cap in Termination Kit, H0908, is a high wind cap Vertical Term- Masonry chimneys may take ination Cap various contours which the Vertical Termination Cap and Flashing. fl exible liners will accomodate. Cat. No. and Flashing, Cat. No. H0908 H0908 However, keep the fl exible liner Liner Requirements: as STRAIGHT as possible, avoid Exhaust Vertical Height Min. = 8 ft. (2.44 M) unnecessary bending

Résumé du contenu de la page N° 11

Flex Liner Installation (see Figure 14 for Step 10. PURGING AIR Masonry Fireplace Installations and Figure 15 for Factory Built Fireplaces): AIR PURGING PROCEDURES MUST BE PERFORMED BY A QUALIFIED TECHNICIAN Note: Refer to Vent Manufacturer Instal- ONLY. lation Instructions. Purging Air from Supply Line Screw a. Turn gas supply line valve off. 1) Cut the fl ex liners as required (mark both b. Loosen setscrew at inlet pressure tap on ends of one of the fl exible liners as INLET). control val

Résumé du contenu de la page N° 12

LOGS, VERMICULITE AND EMBERS - Models EDVI25 & EDVI30 (For 3. Place the Center Log onto the 2 corresponding locating pins as shown in Figure 22. EDVI35 Log Installation Instructions, see Page 13). The packaged log set, vermiculite and embers are located within the fi rebox of the insert. Installation Instructions: WARNING: IF LOGS ARE NOT INSTALLED ACCORDING TO THE DIRECTIONS SHOWN HERE, FLAME IMPINGEMENT AND IMPROPER COMBUSTION COULD OCCUR AND RESULT IN SOOT AND/OR EXCES- SIVE PRODUCTION OF

Résumé du contenu de la page N° 13

Figure 25 Front Center Log 7. Install the Top Right Log into the corresponding indentations on Embers Figure 27 Front Center Log and front right twig as shown in Figure 26. Figure 28 Vermiculite Top Right Log Figure 26 LOGS, VERMICULITE AND EMBERS - Model EDVI35 8. Place the glowing embers on the burner as shown in Figure 27. WARNING: IF LOGS ARE NOT INSTALLED ACCORDING TO THE DIRECTIONS SHOWN HERE, FLAME IMPINGEMENT AND IMPROPER One package of ember material has been included with this log

Résumé du contenu de la page N° 14

Rear Log Front Center Log Figure 32 Figure 29 Vermiculite 6. Install the Top Right Log into the corresponding indentations on Front Center Log and Front Right Log as shown in Figure 33. 3. Place the Front Right Log and the Center Left Log onto the 2 cor- responding locating pins (each) as shown in Figure 30. Top Right Log Figure 33 Center Left Log Front Right Log Figure 30 7. Place the glowing embers on the burner as shown in Figure 34. One package of ember material has been included with th

Résumé du contenu de la page N° 15

T O O W O L I P O N TH TH TP TP O L T H N Step 12. TEST ALL CONNECTIONS FOR Millivolt Appliance Checkout With gas line installed run initial system LEAKS (FACTORY AND FIELD). checkout before closing up the front of the The pilot fl ame should be steady, not lifting unit. Follow the pilot lighting instructions pro- Test For Gas Leaks or fl oating. Flame should be blue in color vided in the Homeowner's Care and Operation A. Mix a 50% dish soap, 50% water solution with traces of orange at the

Résumé du contenu de la page N° 16

Burner Flame Appearance Burner Air Shutter Adjustment Blower Wiring Diagram Adjusting Set Screw Adjustment Rod Up 120 V AC (1/8" Open Position) Burner Tube Power Cord Air Shutter Black Adjustment Rod Down (full open position) Figure 41 EDVI35 FACTORY AIR SHUTTER SETTING Sooting is indicated by black puffs developing INCHES (MILLIMETERS) at the tips of very long orange fl ames. Sooting Models Gas Type Air Shutter Gap results in black deposits forming on the logs, Fan Disc appliance inside s

Résumé du contenu de la page N° 17

SAFETY / LISTING LABELS - MODELS: EDVI30 & EDVI35 MODEL NO. EDVI30 MODEL NO. EDVI35 MANUFACTURED AT: Union City, TN MANUFACTURED AT: Union City, TN FOR USE WITH NATURAL GAS. EQUIPE POUR GAZ NATUREL FOR USE WITH NATURAL GAS. EQUIPE POUR GAZ NATUREL ALTITUDE 0-4500 FT/PI ALTITUDE 0-4500 FT/PI (0-1370M) (0-1370M) MIN. GAS SUPPLY PRESS (“WC) MIN. GAS SUPPLY PRESS (“WC) PRESS MIN. D’ALIMENTATION (“ CE) 4.5” PRESS MIN. D’ALIMENTATION (“ CE) 4.5” MANIFOLD PRESSURE (

Résumé du contenu de la page N° 18

SAFETY / LISTING LABEL - MODEL: EDVI25 MODEL NO. EDVI25 MANUFACTURED AT: Lynwood, CA FOR USE WITH NATURAL GAS. EQUIPE POUR GAZ NATUREL ALTITUDE 0-4500 FT/PI (0-1370M) MIN. GAS SUPPLY PRESS (“WC) PRESS MIN. D’ALIMENTATION (“ CE) 4.5” MANIFOLD PRESSURE (“WC) PRESSION CE TUBULURE (“CE) 3.5” MANUFACTURER’S RECOMMENDED ORIFICE SIZE DIMENSION DE L’INJECTEUR RECOMMANDE PAR MANUFACTURIER (DMS) #41 MAX INPUT (BTU/HR) ENTREE MAX 25,000 MIN INPUT (BTU/HR) ENTREE MIN 17,000

Résumé du contenu de la page N° 19

19 NOTE: THIS PAGE LEFT BLANK INTENTIONALLY. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Résumé du contenu de la page N° 20

Lennox reserves the right to make changes at any time, without notice, in design, materials, specifi cations, prices and also to discontinue colors, styles and products. Consult your local distributor for fi replace code information. Printed in U.S.A. © Lennox Hearth Products 2003 P/N 775,156M REV. G 3/2005 1110 West Taft Avenue  Orange, CA 92865 20 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Lennox Hearth 36" and 42" Wood Burning Fireplaces BR-36/42 Manuel d'utilisation Cheminée 1
2 Lennox Hearth 36" and 42" Wood Burning Fireplaces BCI-36/42 Manuel d'utilisation Cheminée 1
3 Lennox Hearth 36" and 42" Wood Burning Fireplaces BRI-36/42-2 Manuel d'utilisation Cheminée 0
4 Lennox Hearth 36" and 42" Wood Burning Fireplaces BC-36/42 Manuel d'utilisation Cheminée 2
5 Lennox Hearth 36" and 42" Wood Burning Fireplaces BRI-36/42 Manuel d'utilisation Cheminée 3
6 Lennox Hearth 36" and 42" Wood Burning Fireplaces BC-36/42-2 Manuel d'utilisation Cheminée 0
7 Lennox Hearth 36" and 42" Wood Burning Fireplaces BCI-36/42-2 Manuel d'utilisation Cheminée 0
8 Lennox Hearth 36" and 42" Wood Burning Fireplaces BR-36/42-2 Manuel d'utilisation Cheminée 0
9 Lennox Hearth 875027M Manuel d'utilisation Cheminée 0
10 Lennox Hearth Adagio ADAGIO-EN Manuel d'utilisation Cheminée 0
11 Lennox Hearth 4.5HTSK Manuel d'utilisation Cheminée 0
12 Lennox Hearth Adagio ADAGIO-MP Manuel d'utilisation Cheminée 0
13 Lennox Hearth Adagio ADAGIO-MN Manuel d'utilisation Cheminée 0
14 Lennox Hearth ADAGIO-IG H5776 Manuel d'utilisation Cheminée 0
15 Lennox Hearth ADK22CMBS Manuel d'utilisation Cheminée 0
16 Aarrow Fires Becton 7 mk3 Manuel d'utilisation Cheminée 1
17 AEG Royal Belmont G20 Manuel d'utilisation Cheminée 3
18 Austro Flamm Gussofen G3 Manuel d'utilisation Cheminée 1
19 Aarrow Fires Becton Bunny Manuel d'utilisation Cheminée 12
20 Avalon Stoves Victorian Lace DVS Face Black 95200132 Manuel d'utilisation Cheminée 1