Résumé du contenu de la page N° 1
R
Cumberland Gap
Non-Catalytic, Front/Side Load, Wood Heater
Model:
Tested and Portland
CUMBGAP-MBK O-T L
Oregon USA
Listed by
C US
CUMBGAP-PMH OMNI-Test Laboratories, Inc.
This manual contains instructions for Installation, Operation & Maintenance.
Please read this entire manual before you install and use your new room heater. Failure to follow
instructions may result in property damage, bodily injury, or even death.
IMPORTANT SAFETY NOTES:
1) When installing your stove, particular attenti
Résumé du contenu de la page N° 2
R Cumberland Gap Wood Stove and Welcome to the Quadra-Fire Family! yet we are old-fashioned when it comes to craftsmanship. Each Hearth & Home Technologies welcomes you to our tradition of unit is meticulously fabricated and gold and nickel surfaces are excellence! In choosing a Quadra-Fire appliance, you have our hand-finished for lasting beauty and enjoyment. Our pledge to assurance of commitment to quality, durability, and performance. quality is completed as each model undergoes a qua
Résumé du contenu de la page N° 3
R Cumberland Gap Wood Stove TABLE OF CONTENTS PRE-USE CHECK LIST SERIAL NUMBER LABEL & LOCATION ..................2 1. Place the unit in a location near the final installa- PRE-USE CHECKLIST ..............................................3 tion area and follow the procedures below. LISTINGS & SAFETY NOTICES ...............................4 2. Open the stove and remove all the parts and INSTALLATIONS MATERIAL NEEDED FOR SAFETY 4 articles packed inside. Inspect all the parts and VENTING SYSTEM .
Résumé du contenu de la page N° 4
R Cumberland Gap Wood Stove LISTINGS and SAFETY NOTICES These installation instructions describe the installation and operation FIRE SAFETY: To provide reasonable fire safety, the following of the QUADRA-FIRE Cumberland Gap woodstove. This stove should be given serious consideration: meets the U.S. Environmental Protection Agency’s 1990 particulate 1. Install at least one smoke detector on each floor of your emission standards. The Cumberland Gap is listed by OMNI-Test home to ensure your
Résumé du contenu de la page N° 5
R Cumberland Gap Wood Stove DIMENSIONS SERIAL NUMBER LABEL IS LOCATED ON THE BACK OF THE STOVE FRONT VIEW TOP VIEW 16.0" 26-7/8" (406mm) (683mm) C L C L 16-11/16" (424mm) 18-1/8" 12-3/16" (460mm) (310mm) 20-3/16" (513mm) 27-1/4" 2-9/16" (692mm) (65mm) SIDE VIEW SIDE VIEW WITH FUEL DOOR 22-7/8" (581mm) 4-1/2" 20-3/16" (513mm) (114mm) 16-5/8" (422mm) C L C L Back of stove to front 28-3/16" (716mm) fuel loading door 27-11/16" 25.0" 23-1/16" (703mm) (635mm) 27-11/16" (586mm) (703mm) 6-9/16" (167mm)
Résumé du contenu de la page N° 6
R Cumberland Gap Wood Stove CLEARANCES TO COMBUSTIBLES (UL and ULC) E1 B F1 A H Non-fuel C2 door side G (Ceiling) F2 C1 D2 E2 D1 Fuel door Fuel Door side side Non-fuel door side IF SIDE FUEL LOADING DOOR IS NOT USED: • Must remain in the locked position at all times • Use clearances for non-fuel side door for both sides MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS: In Inches & (Millimeters) NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar. TOP VENT VER
Résumé du contenu de la page N° 7
R Cumberland Gap Wood Stove FLOOR PROTECTION Minimum Hearth Requirements ONLY See page 6 for stove clearances The floor must be non-combustible material, extending beneath heater and to the front/sides/rear as indicated. The floor must be a minimum of 1/2" thickness ("k" value = 0.84) non-combustible or otherwise adequately protected from radiant heat given off by the unit and from sparks and falling embers. A layer of thin brick or ceramic tile over a combustible floor is not sufficient. See A
Résumé du contenu de la page N° 8
R Cumberland Gap Wood Stove CORNER INSTALLATIONS - USA ONLY Calculating Alternate Floor Protection Material Thermal Conductivity: k value SIDE FUEL DOOR LOCKED SHUT The k value indicates the amount of heat (in BTU’s) that will flow in 1 hour through 1 square foot of a uniform material 1 inch thick for each degree (F) of temperature difference from one side of the material to the other. The LOWER the k factor means less heat is being conducted through the non-combustible material to the com
Résumé du contenu de la page N° 9
R Cumberland Gap Wood Stove LOCATING YOUR STOVE WHEN LOCATING YOUR STOVE consider safety, convenience, traffic flow, and the fact that the stove will need a chimney and chimney connector. It is a good idea to plan your installation on paper, using exact measurements for clearances and floor protection, before actually beginning the installation. If you’re not using an existing chimney, place the stove where there will be a clear passage for a factory-built listed chimney through the ceiling an
Résumé du contenu de la page N° 10
R Cumberland Gap Wood Stove REVERSIBLE FLUE COLLAR The flue collar is reversible for either a top or rear venting installation. The unit is shipped with the flue collar in the top vent position. ACCESSORY HORIZONTAL FLUE SHIELD Part HTSHLD-7006 IS REQUIRED ON ALL HORIZONTAL INSTALLATIONS. CONVERTING COLLAR FOR REAR VENT INSTALLATION 1. Lift off cast top. Remove 4 Phillips head screws from the Secure heat shield and discard heat shield. See circled areas in Horizontal Flue Figure 10A. Heat
Résumé du contenu de la page N° 11
R Cumberland Gap Wood Stove CHIMNEY HEIGHT REQUIREMENTS / DRAFT 2-10-3 RULE To be sure that your Quadra-Fire stove burns properly, the chimney draft (static pressure) should be approximately -.04” 2 ft Min (61cm) water column (W.C.) during a low burn and -.10” W.C. during 3 ft Min a high burn, measured 6” (152mm) above the top of the stove (91cm) after one hour of operation at each burn setting. NOTE: These are guidelines only, and may vary somewhat for individual installations. 10 ft Mi
Résumé du contenu de la page N° 12
R Cumberland Gap Wood Stove MASONRY CHIMNEY For optimal performance, masonry chimneys used to vent this appliance should be lined with a 6" stain- Wood Stud 2" less steel liner. Installations into a clay flue without (51mm) a stainless steel liner may reduce efficiency, can Clearance cause the glass to darken, and produce excessive Fireclay liner 5/8" from chimney creosote. (16mm) Minimum wall or Equivalent. Ensure that a masonry chimney meets the minimum standards of the National Fire
Résumé du contenu de la page N° 13
R Cumberland Gap Wood Stove SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE For the method of installation to a masonry chimney shown in Figures 14A & 14B on page 14, it will be necessary to purchase a 12" (305mm) long (8" (203mm) inside diameter), section of prefabricated listed solid pack chimney to use as a thimble. Purchase a wall spacer, trim collar, and a wall band manufactured to fit the chimney section you purchase. The safety features of this system are two fold: 1) A 2" (51mm) a
Résumé du contenu de la page N° 14
R Cumberland Gap Wood Stove SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE (Cont'd) Figure 14A First, make the frame for the thimble, ensuring it is no smaller than 14" (356mm) square to maintain a 2" (51mm) air space Min. Chimney Clearance Min. Clearance to Wall Spacer and around the chimney section. 2" (51mm) Combustibles - 2" (51mm) 1" (25mm) Air Space Attach the wall spacer to the chimney side of the frame. Then Chimney Flue Liner to Chimney Section insert the frame into the o
Résumé du contenu de la page N° 15
R Cumberland Gap Wood Stove CONNECTION TO A METAL PREFABRICATED CHIMNEY When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed precisely. It will be necessary to install the ceiling support package or wall pass through, “T” section package, firestops (when needed), insulation shield, roof flashing, chimney cap, and any other materials deemed necessary by the prefabricated chimney manuafacturers' instructions. Maintain the proper clearance to
Résumé du contenu de la page N° 16
R Cumberland Gap Wood Stove MOBILE HOME INSTALLATION You must use a Quadra-Fire Outside Air Kit Part 831-1780 for installation in a mobile home. 1. An outside air inlet must be provided for combustion and must remain Spark Arrestor Cap clear of leaves, debris, ice and/or snow. It must be unrestricted while unit is in use to prevent room air starvation which can cause smoke spillage and an inability to maintain a fire. Smoke spillage Storm Collar can also set off smoke alarms. Roof Flashing
Résumé du contenu de la page N° 17
R Cumberland Gap Wood Stove OUTSIDE AIR KIT INSTALLATION Part 831-1780 Included in Kit: 2 cable ties; oustide air termination cap; mounting screws (Discard the remaining parts). Items Needed for Installation: 4 in. (102mm) diameter flex pipe in the length as required for your installation; Phillips screwdriver; Silicone sealant; Drills and saws necessary for cutting holes through the wall or flooring in your home. 1. Remove all materials from packing box. OUTSIDE AIR 2. Mount the flex flange
Résumé du contenu de la page N° 18
R BENDING TEMPLATE Cumberland Gap Wood Stove STRAIGHT END Lay the flat diverter on the template with the cut ends at the bottom of the tem- plate. Cut Ends HAND BEND #1 Bend the diverter to match the same degree bend as in the template. Hand Bend #1 Baffle Diverter is shipped HAND BEND #2 Hand bend #2 inside firebox. Bend the diverter 90° to complete the process. Place diverter on tem- Straight End plate to confirm the bends match the template. Cut Ends WARNING Risk of Fire. CUT ENDS Requir
Résumé du contenu de la page N° 19
R Cumberland Gap Wood Stove BAFFLE DIVERTER REQUIRED ON ALL HORIZONTAL INSTALLATIONS 1. Open both doors. 2. Hold the diverter in a vertical position with the straight edge going in first and then rotate it to the inside of the firebox as you slide the bent diverter over the ceramic blanket . 3. Place in position as shown in diagram below. The front edge of the diverter will rest on the front edge of the manifold chamber in a flush position. The back edge will butt up against the back slan
Résumé du contenu de la page N° 20
R Cumberland Gap Wood Stove OPERATING INSTRUCTIONS IMPORTANT - PLEASE READ BEFORE USING STOVE OVER-FIRING YOUR APPLIANCE BURNING PROCESS In recent years there has been an increasing concern about air quality. Much of the blame for poor air quality has been WARNING placed on the burning of wood for home heating. In order to improve the situation, we at Quadra-Fire have developed Fire Risk cleaner-burning wood stoves that surpass the requirements Do not over-fire. for emissions established by
