Instruction d'utilisation Harbor Freight Tools 98342

Résumé du contenu de la page N° 1

1/4 HP SUBMERSIBLE
WATER PUMP
98342
SET UP And OPERATIng InSTRUcTIOnS
®
distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MAnUAL.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form w

Résumé du contenu de la page N° 2

8. Access by children should also be Before start-up, note the following: prevented with appropriate mea- The pump can be connected to any sures. shock-proof plug which has been installed 9. WARNING: Handling the Power Cord according to regulations. The plug must on this product will expose you to have a supply voltage of 115 V~ at 60 Hz. lead, a chemical known to the State of California to cause cancer, and cAUTIOn birth defects or other reproductive This pump has been evaluated for h

Résumé du contenu de la page N° 3

2. Make sure that the socket is suf- UnPAckIng ficiently secured and is in excellent When unpacking, check to make sure condition. that the item is intact and undamaged. If 3. When the plug is inserted into the any parts are missing or broken, please socket the pump will be on standby. call Harbor Freight Tools at the number shown on the cover of this manual as soon WARnIng! If the power cord or plug is as possible. damaged, do not use the pump. The power cord or plug may only be re-

Résumé du contenu de la page N° 4

FIgURE B MAInTEnAncE IMPELLER (14) TO PREVEnT SERIOUS InjUR y FROM AccIdEnTAL OPERATIOn: Unplug the Pump from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. If the pump is moved during op- FILTER (11) eration, flush it out with clean water after every use. Quarterly Maintenance The below maintenance must be per- formed at least once every 3 months under a. Remove the Filter (11) from the optimal conditions. For frequent use, or pump cas

Résumé du contenu de la page N° 5

Troubleshooting Problem Possible causes Possible Solutions Pump runs, but 1. Filter and/or impeller clogged. 1. Remove filter. Clean out dirt and debris from will not deliver any filter and impeller. Then replace Filter. water. 2. When starting, the pump water 2. There must be at least 1/8” deep water for the height (1/8”) falls below the Pump to operate properly. minimum water level. 3. Low line voltage. 3. Consult with an electrician. 4. Optional check valve stuck or 4. Remove and examine

Résumé du contenu de la page N° 6

PARTS LIST Part description Qty. Part description Qty. 1 Power Cord & Plug 1 16 Screw 5 2 Water Outlet 1 17 Screw 1 3 Pump Shell 1 18 Hold Down Ring 1 4 O-Ring 1 19 O-Ring 1 5 Cable Guard 1 20 Oil Seal 3 6 Cable Compaction Buckle 1 21 Motor Foreside 1 7 Capacitor 1 22 O-Ring 1 8 Cable Compaction Board 1 23 Motor Lining 1 9 Screw 3 24 Stator 1 10 Screw 4 25 Bearing 2 11 Filter 1 26 Rotor 1 12 Base 1 27 Washer 1 13 Nut 1 28 Back Cover 1 14 Impeller 1 29 Wire Jacket 1 15 Washer 1 SKU 98342 For tech

Résumé du contenu de la page N° 7

ASSEMBLy dIAgRAM SKU 98342 For technical questions, please call 1-800-444-3353. Page 7

Résumé du contenu de la page N° 8

LIMITEd 1 yEAR / 90 dA y WARRAnTy Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Har- bor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that al