Résumé du contenu de la page N° 1
H10X/H5X
H5E/DV PC
With Digital Control Board
Supercedes:
10420.0001; 10889.0001; 39338.0000
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit
the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain
the latest catalog and manual updates.
Résumé du contenu de la page N° 2
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specifi ed below: 2 years parts and 1 year labor. 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years parts and 1 year labor. 4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: parts and labor for 3 years or 30,000 po
Résumé du contenu de la page N° 3
CONTENTS Warranty .......................................................2 Introduction ..................................................3 User Notices .................................................3 Electrical Requirements ................................4 Plumbing Requirements ...............................5 Initial Set-Up .................................................5 Programming ................................................6 Draining the Dispenser ........................
Résumé du contenu de la page N° 4
ELECTRICAL REQUIREMENTS WARNING - The dispenser must be disconnected from the power source until specifi ed in Initial Set-Up. Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements. WHITE NEUTRAL WHITE POWER CORD L2 RED NEUTRAL BLUE POWER CORD L2 RED L2 RED POWER CORD N N L2 NEUTRAL L1 BLACK L1 BLACK L1 BLACK L1 L1 L1 L1 BLACK L1 BROWN L1 BLACK GREEN/YELLOW GREEN GREEN G G G 120 volt ac models 230 volt ac models 208 & 240 volt ac models Note: T
Résumé du contenu de la page N° 5
PLUMBING REQUIREMENTS This dispenser must be connected to a COLD WATER system with operating pressure between 20 and 90 psi 1 (138 and 620 kPa)from a ⁄2” or larger supply line. A shut-off valve should be installed in the line before the dis- penser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 1 kPa). The water inlet fi tting is ⁄4” fl are. 1 3 NOTE - Bunn-O-Matic recommends ⁄4” tubing for installations of less than 25 feet and ⁄8” f
Résumé du contenu de la page N° 6
PROGRAMMING When power is applied to the dispenser, the display located on the bottom of the main circuit board will show the software version for 5 seconds, and then it will show the model number (see chart below) it will then go to (-). While the tank is fi lling, the display will read (FIL). When the tank is full the display will show the model number and then go to (-). MODEL DISPLAYS (H5H) 5 Gallon High Voltage Unit (200-240V) (H5L) 5 Gallon Low Voltage Unit (100-120V) (HPC) 5 Gallon Po
Résumé du contenu de la page N° 7
PROGRAMMING (Continued) LEVEL 2 PROGRAMMING H1 - DISPENSE TEMPERATURE LOCKOUT - PORTION CONTROL ONLY (WILL NOT DISPLAY ON OTHER MODELS) 1. To enter Level 2 Programming, press and hold the center button until H1 ap- pears on the display (approximately 6 seconds) then release button. The display will either read noL (LOCKOUT DISABLED) or Loc (LOCKOUT ENABLED). When (ENABLED), unit will not dispense if the Tank Temperature is below the (READY) temperature setting. 2. Use the (+) or (-) buttons t
Résumé du contenu de la page N° 8
OPERATING CONTROLS - PORTION CONTROL ONLY d. (a) VOLUME SELECTOR BUTTONS Press and release the button corre- c. sponding to the Small, Medium, or Large volume, to select the desired amount of water to be dispensed. Pressing a different button after a cycle has been initiated does not change the volume in progress. (b) AUTO STOP/MANUAL DISPENSE BUTTON Press and release button to stop a dispense cycle. Press and hold button to dispense manually. (c) HIDDEN PROGRAMMING BUTTON a. (d) LED I
Résumé du contenu de la page N° 9
DRAINING THE DISPENSER CAUTION - The dispenser must be disconnected from the power source throughout these steps. 1. Disconnect the dispenser from the power source. 2. Shut-off and disconnect the incoming water supply and allow dispenser to cool. 3. Remove the 4-40 screws and the top cover. 4. Gently remove one of the grommets from the tank lid. 5. Insert a tube to the bottom of the tank and syphon ALL of the water out. NOTE - The dispenser must be full using the INITIAL SET-UP steps before reco
