Résumé du contenu de la page N° 1
1 1 1
1 1
© 2003 Hunter Fan Company 41814-01 01/14/2003
Résumé du contenu de la page N° 2
2 2 2 2 2 If you need help installing the fan, your Hunter fan dealer can di- ® rect you to a licensed installer or electrician. gathering the tools Your new Hunter ceiling fan is an addition to your home or office ® You will need the following tools for installing the fan: that will provide comfort and performance for many years. This • Electric drill with 9/64" bit installation and operation manual gives you complete instructions • Standard screwdriver for installing and operating your fan. •
Résumé du contenu de la page N° 3
3 3 3 3 3 A An ng glle M e Mo oun unt tin ing g A A An n ng g gllle M e M e Mo o oun un unt t tin in ing g g (Figure 3) hangs from a vaulted or angled ceiling. using an existing fan site p pr re ep pa ar rin ing a n g a ne ew f w fa an n If you are preparing a new fan site, go to the p p pr r re e ep p pa a ar r rin in ing a n g a n g a ne e ew f w f w fa a an n n º si sit te e 34 Max si si sit t te e s e ection. If you plan to use an existing fan site, complete the following check- list for the
Résumé du contenu de la page N° 4
4 4 4 4 4 cutting the ceiling hole preparing the wiring 1. Locate the site for the hole directly below the joist or support C C C C CA A A A AU U U U UT T T T TI I I I IO O O O ON: A N: A N: A N: A N: All w ll w ll w ll w ll wir ir ir ir irin in in in ing mu g mu g mu g mu g mus s s s st b t b t b t b t be in a e in a e in a e in a e in ac c c c cc c c c co o o o or r r r rd d d d da a a a an n n n nc c c c ce w e w e w e w e wi iii it t t t th n h n h n h n h na- a- a- a- a- brace that wil
Résumé du contenu de la page N° 5
5 5 5 5 5 4. Align the slotted holes (refer to Figure 10) in the ceiling plate with the pilot holes in the wood support structure. Note: The Hanger Ball/ isolation pads should be flush against the ceiling. Downrod Assembly For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows on the ceiling plate are pointing towards the ceiling Canopy peak. Refer to Figure 10. Canopy Trim Ring Slots Set Screw F F F F Fi iii ig g g g gur ur ur ur ure 12 - A e 12 - A e 12 - A e 12 - A e 1
Résumé du contenu de la page N° 6
6 6 6 6 6 6. Place the canopy trim ring then the canopy over the adapter • control the light with one wall switch and the fan with as shown in Figure 15. another (two wall switches required). 7. Place the low profile washer (lip up) into the canopy as shown Use connection 2, as described in Figure 17, if there is no sepa- in Figure 15 fitting the notch in the low profile washer over the rate wall switch power wire for the light fixture. adapter set screw and hook. NOTE: Wall switches not includ
Résumé du contenu de la page N° 7
7 7 7 7 7 For Flush Mounting: The arrows on the low profile washer and on the ceiling plate should be pointing in the same direction assembling the blades and should be pointing towards the tab hole on the canopy. Hunter fans use several styles of fan blade irons (brackets that hold 2. Hook the tab hole over the tab on the ceiling plate as shown in the blade to the fan). Figure 19. 1. Your fan may include blade grommets. If your fan has grom- 3. Raise the canopy, be sure the holes in the canopy
Résumé du contenu de la page N° 8
8 8 8 8 8 Housing Switch Housing Assembly Blade Iron Mounting Plate Screw Upper Plug Connector Upper Switch Housing F F Fiiig g gur ur ure 26 - A e 26 - A e 26 - At t tt t ta a ac c ch h hin in ing t g t g th h he up e up e upp p pe e er s r s r sw w wiiit t tc c ch h h h h ho o ou u usin sin sing t g t g to t o t o th h he e e F Fiig gur ure 26 - A e 26 - At tt ta ac ch hin ing t g th he up e upp pe er s r sw wiit tc ch h h ho ou usin sing t g to t o th he e m m m m mo o o o oun un un un unt t
Résumé du contenu de la page N° 9
9 9 9 9 9 7. Thread the two wires from the light fixture through the center attaching the lower switch housing hole in the lower switch housing. 8. Connect the black wire from the light fixture to the black/white 1. Connect the upper plug connector from the motor to the lower wire from the lower switch housing. plug connector in the lower switch housing assembly. See Fig- Connect the white wire from the light fixture to the white wire ure 30. from the lower switch housing. NOTE: Both plug connec
Résumé du contenu de la page N° 10
10 10 10 10 10 installing the lower switch housing operating your ceiling fan 1. Connect the upper plug connector from the motor to the lower 1. Turn on electrical power to the fan. plug connector in the lower switch housing assembly. See Fig- 2. The fan pull chain controls power to the fan. The pull chain ure 30 has four settings in sequence: High, Medium, Low and Off. NOTE: Both plug connectors are polarized and will only fit to- • Pull the chain slowly to change settings. gether one way. Make
Résumé du contenu de la page N° 11
11 11 11 11 11 cleaning your ceiling fan troubleshooting Problem: Nothing happens; fan does not move. caring for finishes 1. Turn power on, replace fuse, or reset breaker. For cleaning, a soft brush or lint-free cloth should be used to pre- 2. Loosen canopy, check all connections according to the vent scratching the finish. A vacuum cleaner brush nozzle can re- w w wir ir irin in ing t g th he f e fa an n w wir irin ing t g t g th h he f e f e fa a an n n section. move heavier dust. Surface
