Instruction d'utilisation Emerson CF942OB00

Résumé du contenu de la page N° 1

READ AND SAVE THESE INSTRUCTIONS
®
™
Model No.
HEARTWICK
CF942OB00
Ceiling Fan
CF942TG00
CF942HTW00
Owner's Manual
CF942WB00
CF942SB00
Net Weight: 21.8 Lbs.
CF942BS00
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this w

Résumé du contenu de la page N° 2

WARNING ! WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of

Résumé du contenu de la page N° 3

This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One stepladder Installed Wire Length Wire Size A.W.G. One 1/4” blade screwdriver One wire stripper Up to 50 ft. 14 One 5/16” open end wrench, or pliers 50-100 ft. 12 Three wire connectors (supplied). ! WARNING MATERIALS Before assembly your ceiling fan, refer to section on Wiring outlet box and box connectors must be of

Résumé du contenu de la page N° 4

How to Put Your Ceiling Fan Together 1. Remove the hanger ball by loosening the setscrew NOTE: The setscrew and jamnut must be properly in the hanger ball until the ball falls freely down the installed as described above, or fan wobble could downrod (Figure 1). Remove the pin from the result. downrod, then remove the hanger ball. Retain the 4. Make sure the grommet is properly installed in the pin and hanger ball for reinstallation in step 5. coupling cover, then slide the coupling cover on the

Résumé du contenu de la page N° 5

SWITCH ! WARNING HOUSING ASSEMBLY To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, bal- ancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. 3/16-24 x 3/8" SLOTTED PHILLIPS HEAD SWITCH HOUSING SCREW (3) PLASTIC WASHER (3) ASSEMBLY FELT WASHER (3) MOTOR CONNECTOR FAN BLADE Figure 7 Figure 5 BLADE FLANGE 12. Remove the four mounting screws from the switch housing plate. Attach the switch housing

Résumé du contenu de la page N° 6

How to Hang Your Ceiling Fan OUTLET ! WARNING BOX The fan must be hung with at least 7' of clearance from floor to blades (Figure 9). CEILING TWO SCREWS SUPPLIED WITH HANGER OUTLET BOX BRACKET TAB Figure 10 Figure 2 AT LEAST 7' 2. Carefully lift the fan and seat the hanger ball/ downrod assembly on the hanger bracket that was Figure 9 FLOOR just attached to the outlet box (Figure 11). Be sure the groove in the ball is lined up with tab on the ! WARNING hanger bracket (Figure 10). The outlet box

Résumé du contenu de la page N° 7

BLACK AND BLUE 5. Secure the ceiling cover in place by sliding lockwash- FAN WIRES GROUND ers over the threaded studs and installing the two WIRE knurled knobs (supplied). (Figure 13.) Tighten the LISTED knurled knobs securely until the ceiling cover fits WHITE SUPPLY WIRE (NEUTRAL) CONNECTOR (3) snugly against the ceiling and the hole in the ceiling cover is clear of the downrod. Your fan is now wired to be turned on and off from the fan switch. GREEN WIRE CEILING COVER (GROUND) FROM WHITE FAN

Résumé du contenu de la page N° 8

! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan, or loose 2. Check line wire connections to fan and switch switch wire switch wire connections in the switch housing. connections in the switch housing.wire connections in