Résumé du contenu de la page N° 1
FLAT PANEL
MICATHERMIC
HEATER
USER MANUAL
Model # HGW-308
3057224
PLEASE SAVE THESE INSTRUCTIONS
Résumé du contenu de la page N° 2
Table of Contents INTRODUCTION………………………………………………….……..……… 3 Special Features…………………………………………………………… 3 Specifications……………………………………………………………… 3 HEATER DIAGRAM………………………………………………….………… 4 ASSEMBLY………………………………………………………………..…..… 5 Remove Packaging………………………………………………………… 5 Installation……………………..………………………………..….……… 6 IMPORTANT SAFEGUARDS……………………………………..……….…… 7 OPERATION…………………………………………………………..………… 8 CLEANING……………………………………………………….………....…… 10 STORAGE……………………………………………………….…
Résumé du contenu de la page N° 3
FLAT PANEL MICATHERMIC HEATER Introduction Micathermic heat utilizes technology from both convection and reflective heat. The heater releases 80% convection and 20% reflective heat, distributing heat consistently and more evenly throughout the room. The heater radiates heat to warm surrounding objects, increasing the room temperature. As the surrounding objects absorb heat, the air temperature rises. Nowadays, saving energy is very important. Our heater features an ECO
Résumé du contenu de la page N° 4
Heater Diagram 1. Power Switch 2. ECO Green Light Indicator 3. Temperature Control Knob 4. Temperature Control Red Light Indicator 5. Power Supply Cord 6. Foot with Caster 7. Metal Grille 8. Built-in Handle 9. Mounting Hole 10. Mounting Support 11. Screws 12. Mounting Anchor for Wall Mounting 4
Résumé du contenu de la page N° 5
Assembly Remove Packaging PLEASE READ ALL INSTRUCTIONS BEFORE OPERATING HEATER! 1. Remove the heater from the box. 2. Remove the poly foam from both ends of the heater, and remove the poly bag. 3. Remove the 2 remaining bags from the box. One bag contains: 2 feet with casters. [Fig 1] The other bag contains: 1 mounting support, 2 screws and 2 mounting anchors for wall mounting. [Fig 2] 4. Save the packaging for storing the heater while it is not in use
Résumé du contenu de la page N° 6
Installation Required Tools for Floor Use: Phillips screwdriver (not supplied) Estimated Assembly Time for Floor Use: 1 minute Assembly Instructions for Floor Use: Insert the feet and bolts onto the unit as shown in the diagram. Required Tools for Wall Mounting: Phillips screwdriver (not supplied), Drill (not supplied), Hammer (not supplied) Mounting Instructions: STEP 1 Using the mounting support as a guide, mark the first screw hole on the wall. STEP 2 Move t
Résumé du contenu de la page N° 7
Important Safeguards PLEASE READ ALL INSTRUCTIONS BEFORE OPERATING HEATER! The heater is hot when in use. To avoid burns, do not let bare skin touch hot surface. Use handles when moving this heater. Keep combustible materials, such as drapery and other furnishings, at least 3 feet (0.9M) from the front of the heater and away from its sides and rear. Do not leave the heater unattended while it is in operation. Extreme caution is necessary when any heater is used by o
Résumé du contenu de la page N° 8
Operation PLEASE READ ALL INSTRUCTIONS BEFORE OPERATING HEATER! 1. Make sure the Temperature Control Knob is at the “DOT” position. [Fig 1] Make sure the power switch is at the off position. [Fig 2] 2. Plug the power cord into a suitable electrical outlet. [Rated not less than 115 volt]. 3. Turn the power switch to the “ON” position. Adjust the Temperature Control Knob clockwise until the Red Light Indicator turns on [Fig 2]. The Temperature Control should begin.
Résumé du contenu de la page N° 9
4. Comfortable Zone To obtain a desirable temperature, there is an area indicated on the Temperature Control Knob known as the “Comfortable Zone.” You can adjust the knob to select a temperature within this range. 5. Anti-Freeze Setting This setting keeps the temperature of the surrounding area above freezing to prevent pipes from breaking. To do this, simply plug in the heater and turn the Temperature Control Knob to the “Snowflake” position. The heater will automatical
Résumé du contenu de la page N° 10
Cleaning Before cleaning, turn off the heater, unplug the power cord and allow the heater to cool. Do not immerse the power cord, plug or heater in water or other liquid or pour water or other liquid over the heater. Use a vacuum cleaner to remove dust and lint from the metal grille of the heater. Wipe the heater with a dry cloth to remove dust and a damp cloth [not wet] to clean off stains. Do not use detergents, abrasive cleaning powder or polish of any kind on the
Résumé du contenu de la page N° 11
WARRANTY One Year Limited Warranty Soleus International Inc. warrants the accompanying Soleus Air HGW-308 to be free of defects in material and workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the date of original retail purchase in the United States or Canada. If the heater exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of charge within a reasonable time du
