Instruction d'utilisation Monte Carlo Fan Company 5CSR60AGD Series

Résumé du contenu de la page N° 1

Owner’s
Manual
Ceiling Fan Installation Instructions
For 5CSR60AGD Series Fans
READ AND SAVE THESE INSTRUCTIONS
Total fan weigh
with light

Résumé du contenu de la page N° 2

Installation SAFETY TIPS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS 1. Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70- 1999), including fire-rated construction. 2. Use this unit only in the manner intended by the manufacurer. If you have any questions contact the manufacturer. 3. After making the wire connections,

Résumé du contenu de la page N° 3

7 8 9 Lift mounting neck to mounting Plate and align Secure mounting neck to the mounting plate Remove keeper from cross pin and with four screws to become a complete mount- screws. then cross pin from yoke. Replace ing bracket. keeper on cross pin and save. 10 11 12 Loosen lock nuts and screws on yoke Loosen set screw that holds ball. Slide ball down and remove pin save till you can not feel screw on inside pin for later. of yoke. 13 14 15 Install downrod into yoke. Align hole Tighten 2 downro

Résumé du contenu de la page N° 4

21 19 20 Tighten screw on arch hub into Install lower foot of arch arm with Install arch arms to arch hub using downrod to hold in place. screws to fan upper housing. screws removed step 18. 22 23 24 Install arch hub cover onto downrod. Install canopy onto downrod. Thread leadwires and safety cable through ball. 25 26 27 Tighten set screw to hold ball in Place ball on downrod. Replace pin Tighten set screw to hold ball in removed earlier and pull ball up so that place. place. the pin fits in th

Résumé du contenu de la page N° 5

31 32 33 white black Make wiring connections as indicated above. White from fan to white from remote marked Make wire connections to power source using N. Blue from fan to blue from remote marked wire nuts provided. Make sure that no filiments light. Black from fan to Black from remote are outside of the wirenut. After making the marked L. White from house to white from Install remote receiver by sliding into opening in wire connections, the wires should be spread remote marked AC N . Black fro

Résumé du contenu de la page N° 6

43 44 45 Remove finial nut from light fitter. Remove hex nut and rubber washer Install glass onto light kit, install from light fitter. rubber washer and hex nut to hold in place and tighten in direction of arrow. 46 47 48 HAND HELD INSTALL Remove cover by snaping off from top or bot- tom. Remove battery cover. Install 12V battery Install finial cap and finial nut and Place face plate over battery compartment and into wall remote. Duracell MN21 / Eveready A23 buttons. Place remote over 2 pins

Résumé du contenu de la page N° 7

Remote Control Transmitter Features: FAN REVERSE LED LIGHT (Press once to change direction of MEDIUM SPEED the fan)Fanmust be running to reverse. LOW SPEED HIGH SPEED FAN OFF SETTING LIGHT ON/OFF SET- (Turns fan off only) TING AND DIMMER (Press and hold to dim light infinitively) FAN SPEED Depress “l dot” for low speed, “2 dots” for medium or “3 dots” for high. To turn fan off press square”. LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off press once quickly while lig

Résumé du contenu de la page N° 8

Trouble Shooting If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our Customer Service Center at the number printed on your parts list insert sheet. Warning: Before servicing or cleanin

Résumé du contenu de la page N° 9

6/21/06 REV.0 New made from 5GMR manual